2AANZCCSELBTCoca-Cola Wireless Selfie Stick

DGL Group LTD. Coca-Cola Wireless Selfie Stick Mode No.: CC-SLF-BT-ASST Thanks for your support of this wireless mobile phone monopod from Kjstar Co.,Ltd China.This monopod is based on the Bluetooth HID wireless communication technology.please confirm that your samart phone supports this technology.This monopod can intelligently recognizies and works with smart phones with IOS 4.0 or Android 3.0 and above Also it can be manually switched if necessary. 1. Function Autodyne and vide wirelessly by Mobile 2. Description of the whole package: 1 piece phone clamp , 1 piece Gasket ,1 piece USB charging cable, 1 piece user manual, 1piece Warranty card 3. Specification 3.1 Working enviroment temperature:- 10-+40°C 3.2 working enviroment relative Humidity:10%-90% .1. 3.3 Battery Capacity: 55Mah 3.4 charging Voltage: DC 5.0V 3.5 Autodyne Frequence: 500times 3.6 Standby Time: 100 hours 3.7 Charging time: 1hour 3.8 Memory quantity: 4times 3.9 The product automatically goes to “sleep”within 2 hours unused, it will “wake up”5 seconds later after pressing the key of “press” 4. Usage intructions 4.1 Full charging time: 1 hourle 4.2 Paring: Mobile phone and Monopod Apple IOS System: Open the “setting”→Bluetooth→turn on monopod→Searching autodyne→ system “Kjstar” →enter system→complete Paring Android System: open the “setting” →Bluetooth→Scanning→turn on the monopod→Searching autodyne system “Kjstar” →enter the system→complete paring .2. ★ The paringof the camera and monopod need not password,The paring is on-going when the blue LED light is flashing quickly,please operate it within 40 seconds,otherwise you need to restar the power,rescan and repair. 4.3 Autodyne Put the mobile phone to the monopod→enter the camera application “” →stretch the monopod→press the key of “press” ★ some devicees with the android system might not normally work with the monopod in that case,please download an APP “Kjstar-365”from our website or you can aslo try switch the system of the monopod 5. Switch of the system: Push the “press”button and turn one the power of the monopod in the same time and then pair it with your device. .3. 6. Caution and safety 6.1 Press read the instruction carefully before uasage 6.2 Please turn off the nearby bluetooth to 6 avoid the signal interference 6.3it may conflict when using some mobile phone keyboard with it simultaneously, please close the bluetooth or turn off the power of the monopodl 6.4 Safety 6.4.1 please do not dismantle the products 6.4.2 please do not use corrosive solvent to clean it 6.4.3 Forbidden to use it or charging under high temperature or strong light 6.4.4 Forbidden to use it in the rain with damp or soaked 6.4.5 Forbidden to throw it into the fire, so as to avoid the explosion 6.4.6 Please do not knock it heaviy .4. 7. Other cautions: 7.1 No power or poower turned off: LED turned off 7.2 Bluetooth pairing: Bluetooth LED Light keep flashing at middle frequency 7.3 Taking photo:Blue LED light flash one time 7.4 Blue paring Sucessfuly or wake up Sleep: LED light keep flashing quickly 7.5 Low voltage: LED light keep flashing slowly 7.6 Charging : Red LED light on,full charging red LED Light off .5. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

DGL Group LTD. Address: 195 Raritan Center Parkway Edison, New Jersey 08837, United States Tel: 86-755-82824432 Fax.: 86-755-82824476 2015-08-26 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID:2AANZCCSELBT We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics Diagram - Block Diagram - Operation description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title: Josephine Tran / Manager Contact information / address: 195 Raritan Center Parkway Edison, New Jersey 08837, United States Tel: 86-755-82824432 Fax.: 86-755-82824476 Email: [email protected]

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Fig.6

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size: L3.0cm*W2.0cm Material: Tagboard Glue: adhesive sticker Font color: Black Label color: White Label And Location Coca-Cola Wireless Selfie Stick ModelNo.:CC-SLF-BT-AST FCC ID: 2AANZCCSELBT Input: DC 5V/0.5A

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. INTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Fig.6 Bluetooth Antenna

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E ___________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 FCC RF Exposure Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Portable Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v05r02 FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v05r01Section 4.3.1 Standalone SAR test exclusion considerations:“ Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E ___________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 Conducted Power Results Bluetooth Mode Channel Frequency (MHz) Peak Conducted Output Power (dBm) GFSK 00 2402 1.22 39 2441 1.13 78 2480 1.25 Manufacturing tolerance Bluetooth GFSK (Peak) Channel Channel 00 Channel 39 Channel 78 Target (dBm) 1.0 1.0 1.0 Tolerance ±(dB) 1.0 1.0 1.0 Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW GFSK 2.402 0 2.0 1.5849 0.5<3.0 Yes 2.441 0 2.0 1.5849 0.5<3.0 Yes 2.480 0 2.0 1.5849 0.5<3.0 Yes Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v05r02. .......................END OF REPORT.........................

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 41 FCC TEST REPORT FOR DGL Group LTD. Coca-Cola Wireless Selfie Stick Model No.: CC-SLF-BT-ASST Additional Model No.: CC-SLF-BT-BLK, CC-SLF-BT-RED, CC-SLF-BT-SLV Prepared for : DGL Group LTD. Address : 195 Raritan Center Parkway Edison Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : August 14, 2015 Number of tested samples : 1 Serial number : Prototype Date of Test : August 14, 2015 – August 21, 2015 Date of Report : August 21, 2015 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 41 FCC TEST REPORT FCC CFR 47 PART 15 C(15.247): 2014 Report Reference No. ............... : LCS1508140867E Date of Issue ................................. : August 21, 2015 Testing Laboratory Name .......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ......................................... : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Testing Location/ Procedure ......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : DGL Group LTD. Address ......................................... : 195 Raritan Center Parkway Edison Test Specification Standard ........................................ : FCC CFR 47 PART 15 C(15.247): 2014 Test Report Form No. ................... : LCSEMC-1.0 TRF Originator ............................. : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ................ : Coca-Cola Wireless Selfie Stick Trade Mark ................................... : Cocacola Model/ Type reference .................. : CC-SLF-BT-ASST Ratings .......................................... : DC 3.7V by battery (55mAh) Recharge Voltage: DC 5V/500mA Result ......................................... : Positive Compiled by: Supervised by: Approved by: Dick Su / File administrators Glin Lu/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 41 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1508140867E August 21, 2015 Date of issue Type / Model........................... : CC-SLF-BT-ASST EUT......................................... : Coca-Cola Wireless Selfie Stick Applicant............................... : DGL Group LTD. Address.................................. : 195 Raritan Center Parkway Edison Telephone............................... : / Fax.......................................... : / Manufacturer........................ : DGL Group LTD. Address................................... : 195 Raritan Center Parkway Edison Telephone............................... : / Fax.......................................... : / Factory................................... : DGL Group LTD. Address................................... : 195 Raritan Center Parkway Edison Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 41 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .................................................................................................. 5 1.1 Description of Device (EUT) .......................................................................................................... 5 1.2 Support equipment List .................................................................................................................... 5 1.3 External I/O Cable ............................................................................................................................ 5 1.4 Description of Test Facility .............................................................................................................. 6 1.5 Statement of The Measurement Uncertainty .................................................................................... 6 1.6 Measurement Uncertainty................................................................................................................. 6 1.7 Description Of Test Modes .............................................................................................................. 7 2. TEST METHODOLOGY ............................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement (X Position) Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AANZCCSELBT Report No.: LCS1508140867E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 1.2. Photo of Line Conducted Emissions