2AAQFQ2Bluetooth Speaker

Q2 说明书 材质：105G单铜 ，单面印刷卡 尺寸为：140*212mm CUBE CUBE Art.No.: 7199-64 Made in China CUBE 150Hz-18KHz 1.5 1.5~ 70 Micro 3.5mm JACK USB PORTON/OFF LED (RED/BLUE) 140mm 212mm 150327-002 134-POQ2-001R This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

FCC INFORMATION (additional) Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Report No.: ECT2015E01248 Page 1 of 1 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China External View of EUT Model: Q2 Photo 1 Model: Q2 Photo 2

丝印白色字体 黑底不干胶贴纸：白色文字 过光膜 Q2 备注：送大货样，工程部确认尺寸、 颜色及丝印内容后方可做大货 黑色普通不干胶，黑底白字 过光膜 Q2 150318-002 133-0BTQ4A-001R 28mm 贴纸 位置示意图 18mm FCC ID: 2AAQFQ2 Input: DC 5V 500mA Made in China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Model No.: Q2 FCC ID: 2AAQFQ2 Input: DC 5V 500mA Made in China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Model No.: Q2

Report No.: ECT2015E01248 Page 1 of 3 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Internal View of EUT Model: Q2 Photo 1 Model: Q2 Photo 2 Report No.: ECT2015E01248 Page 2 of 3 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: Q2 Photo 3 Model: Q2 Photo 4 Report No.: ECT2015E01248 Page 3 of 3 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: Q2 Photo 5

Report No.: ECT2015E01248 Page 1 of 1 Rev: None RF Exposure Compliance Requirement The product belongs to standalone portable device base the FCC rule part 2.1091&2.1093. The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. The Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: Transmit frequency (GHz) Max Conducted Output Power (mW) SAR Test Exclusion Threshold (mW) 2.402 3.499 9.7 2.441 6.138 9.6 2.480 6.209 9.5 The SAR Test Exclusion Threshold for 100 MHz to 6 GHz is calculated from: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v05r02, the SAR report is not required.

Report No.: ECT2015E01248 Page 1 of 58 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China FCC Test Report Part 15 subpart C Client Information: Applicant : CHINA ELECTRONICS SHENZHEN COMPANY Applicant add.: F35/F, ELECTRONICS SCIENCE AND TECHNOLOGY BUILDING, SHENNANZHONG ROAD, SHENZHEN, CHINA EUT Information: EUT Name : BLUETOOTH SPEAKER Model No. : Q2, 7199-64BK, 7199-64RYL Brand Name : N/A FCC ID : 2AAQFQ2 Prepared By: Shenzhen ECT Testing Technology Co., Ltd. Add. : Room 1106, Era Innovation Certer, Xixiang gushu second road, Baoan district, Shenzhen city, China Date of Receipt: Apr. 08, 2015 Date of Test: Apr. 08~ Apr. 14, 2015 Date of Issue: Apr. 14, 2015 Test Result: Pass Test procedure used: ANSI C63.4-2009 This device described above has been tested by Shenzhen ECT Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. *This test report must not be used by the client to claim product endorsement by any agency of the U.S. government. Reviewed by: Approved by: Nancy Xu kelly Jiang Report No.: ECT2015E01248 Page 2 of 58 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China 1 Contents Page COVER PAGE 1 CONTENTS ...........................................................................................................................................................2 2 TEST SUMMARY ..................................................................................................................................................4 2.1 COMPLIANCE WITH FCC PART 15 SUBPART C.....................................................................................................4 2.2 MEASUREMENT UNCERTAINTY............................................................................................................................4 3 GENERAL INFORMATION...................................................................................................................................5 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................................................5 3.2 DESCRIPTION OF TEST CONDITIONS....................................................................................................................7 3.3 EUT PERIPHERAL LIST.......................................................................................................................................8 3.4 TEST PERIPHERAL LIST......................................................................................................................................8 4 EQUIPMENTS LIST FOR ALL TEST ITEMS .......................................................................................................9 5 TEST RESULT.....................................................................................................................................................10 5.1 ANTENNA REQUIREMENT..................................................................................................................................10 5.1.1 Standard requirement............................................................................................................................10 5.1.2 EUT Antenna .........................................................................................................................................10 5.2 CONDUCTION EMISSIONS MEASUREMENT.........................................................................................................11 5.2.1 Applied procedures / Limit .....................................................................................................................11 5.2.2 Test procedure.......................................................................................................................................11 5.2.3 Test results ............................................................................................................................................12 5.3 RADIATED EMISSIONS MEASUREMENT..............................................................................................................14 5.3.1 Applied procedures / Limit .....................................................................................................................14 5.3.2 Test procedure.......................................................................................................................................14 5.3.3 Test Result.............................................................................................................................................15 5.3.4 TEST RESULTS (Restricted Bands Requirements)..............................................................................20 5.4 BANDWIDTH TEST.......................................................................................................................................26 5.4.1 Applied procedures / Limit .....................................................................................................................26 5.4.2 Test procedure.......................................................................................................................................26 5.4.3 Deviation from standard.........................................................................................................................26 5.4.4 Test setup ..............................................................................................................................................26 5.4.5 Test results ............................................................................................................................................27 5.5 CARRIER FREQUENCIES SEPARATED......…

Text truncated - open the document above for the full version.

Report No.: ECT2015E01248 Page 1 of 2 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Test Setup Photograph Conducted Measurement Photos Report No.: ECT2015E01248 Page 2 of 2 Rev: None Shenzhen ECT Testing Technology Co., Ltd. Room 1106, Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Radiated Measurement Photos 30MHz-1GHz 1GHz-25GHz