2AASC-81013Bluetooth Stereo Clock radio speaker

Model# 81013 Printed in China ONE-YEAR LIMITED WARRANTY NYL Holdings LLC warrants the original consumer purchaser of this product that it shall be free of defects in materials and workmanship for one year from the purchase date of this product. Defects caused by tampering, improper use, unauthorized modifications or repairs, immersion in water or abuse are not covered by this warranty. If a defect covered by this warranty occurs during the warranty period, package your clock carefully and send it to: Att: Repair center / NYL Holdings LLC 1212 East Broward Blvd. Suite 203 Fort Lauderdale, FL 33301 (954) 462-6848 You must include a Proof of Purchase, either the original receipt or a photocopy and a check or money order for USD $14.95 to cover the cost of shipping and handling. Also include your return address inside the package. NYL Holdings LLC will repair or replace the clock and return it to you. NYL Holdings LLC will not be liable for any loss or damages, including incidental or consequen- tial damages of any kind: from any breach of warranty either expressed or implied relating to the product. Since some states do not allow the exclusion or limitation of incidental or consequential damages, these limitations may not apply to you. This warranty gives you specific legal rights, and you may have other rights that vary from state to state. USB CHARGING (FOR MOBILE PHONES) To charge your smartphone, connect your USB charging cord to the USB charging port located on the back of the clock. Note: This USB charging port may not support all phones, tablets or devices. GETTING STARTED INSTRUCTIONS & WARRANTY AUDIO SOURCE INDICATORS (AUX, BLUETOOTH, or FM) TIME SET / ALARM 1 & 2 SET MUSIC OFF SLEEP SNOOZE / DIMMER ALARM BUZZER icon TIME DISPLAY RADIO PRESETS PHONE (BLUETOOTH) PLAY / PAUSE ALARM STOP MUSIC ON AUDIO SOURCE SELECTOR (AUX, BLUETOOTH, or FM) TUNE / VOLUME HOUR / MINUTE RADIO FREQUENCY ALARM 1 & 2 ON INDICATORS AM / PM INDICATORS SNOOZE INDICATOR SLEEP INDICATOR USB CHARGING PORT AUX (3.5mm) INPUT POWER ADAPTER INPUT Connect the POWER ADAPTER (MICRO USB CABLE) into the back of the clock, and the other end into a standard electrical outlet. To ANSWER an incoming call, press the PLAY / PAUSE button once. To END a call, press the PLAY / PAUSE button once. #1 To re-dial, the last outgoing call (made by your phone) press the PLAY / PAUSE button twice. #2 Note: To use hands free calling, the bluetooth must be turned and paired to the clock. When there is an incoming call, the clock will announce the phone number of the incoming call. Note: To IGNORE an incoming call, press the PLAY / PAUSE twice. HANDS FREE CALLING DISPLAY DIMMER Press the DIMMER button repeatedly to adjust the display brightness. Each time the dimmer is pressed the display will change brightness. Note: There are four levels of display brightness. OFF SOFT MEDIUM BRIGHT FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC RF warning statement: the device has been evaluated to meet general RF exposure requirement , The device can be used in portable exposure condition without restriction.

Shenzhen Alpinor Technology Company Limited Model Difference FCC ID: 2AASC-81013 Model : 81013, 81013cn,A9,A9L All the models are the same circuit and RF module, except the mode names. Regards, Client’s signature Signature Client’s name / title : XieYi / EM Contact information / address : JingHua Industrial Park, PingHu LongGang ShenZhen China

Shenzhen Alpinor Technology Company Limited SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 Shenzhen Alpinor Technology Company Limited SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 2014/5/7 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, _____ _ Shenzhen Alpinor Technology Company Limited ____ hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product： Bluetooth Stereo Clock radio speaker Trade Name： Westclox Model Name： 81013 Serial Model： 81013cn,A9,A9L FCC ID : 2AASC-81013 We affirm that between SIEMIC and __ _ Shenzhen Alpinor Technology Company Limited __, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Signature Name: XieYi Title: EM Address: JingHua Industrial Park, PingHu LongGang ShenZhen China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Shenzhen Alpinor Technology Company Limited 2014/5/7 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AASC-81013 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Signature Client’s name / title : XieYi / EM Contact information / address : JingHua Industrial Park, PingHu LongGang ShenZhen China

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7

FCC ID LABELING AND LOCATION FCC ID Label Bluetooth Stereo Clock radio speaker Model NO.: 81013 Westclox Input Rating: DC 5V/ 1000mA FCC ID: 2AASC-81013 shenzhen Alpinor Technology Company Limited. Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 ANT Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10

FCC ID : 2AASC-81013 RF EXPOSURE EVALUATION METHOD FCC ID: 2AASC-81013 SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Maximum measured transmitter power. BT 1Mbps Test Channel Frequency (MHz) Peak Output Power (dBm) Peak Output Power (mW) CH00 2402 0.107 1.025 CH39 2441 -0.739 0.844 CH78 2480 0.130 1.030 2Mbps CH00 2402 -0.444 0.903 CH39 2441 -1.047 0.786 CH78 2480 -0.440 0.904 3Mbps CH00 2402 0.027 1.006 CH39 2441 -0.751 0.841 CH78 2480 -0.009 0.998 Remark: The best case gain of the antenna is 1.0dBi. FCC ID : 2AASC-81013 1.0 dBi logarithmic terms convert to numeric result is nearly 1.26 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)] BT Mode [(max. power of channel, including tune-up tolerance, mW) (min. test separation distance,mm)] [√f(GHz)] Result Limit 1Mbps CH00 1.025 5 2.402 0.318 3 CH39 0.844 5 2.441 0.264 3 CH78 1.030 5 2.480 0.325 3 2Mbps CH00 0.903 5 2.402 0.280 3 CH39 0.786 5 2.441 0.246 3 CH78 0.904 5 2.480 0.285 3 3Mbps CH00 1.006 5 2.402 0.312 3 CH39 0.841 5 2.441 0.263 3 CH78 0.998 5 2.480 0.314 3 The test Result is less than 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Conclusion: No SAR is required.

FCC RADIO TEST REPORT FCC ID: 2AASC-81013 Product： Bluetooth Stereo Clock radio speaker Trade Name： Westclox Model Name： 81013 Serial Model： 81013cn,A9,A9L Report No.： NTEK-2014NT0327576F Prepared for Shenzhen Alpinor Technology Company Limited. JingHua Industrial Park, PingHu, LongGang, ShenZhen, China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 74 Report No.:NTEK-2014NT0327576F TEST RESULT CERTIFICATION Applicant’s name................. : Shenzhen Alpinor Technology Company Limited. Address ................................. : JingHua Industrial Park, PingHu, LongGang, ShenZhen, China  Manufacture's Name............ : Shenzhen Alpinor Technology Company Limited. Address ................................. : JingHua Industrial Park, PingHu, LongGang, ShenZhen, China Product description Product name ........................... : Bluetooth Stereo Clock radio speaker Model and/or type reference : 81013 Serial Model： 81013cn,A9,A9L Standards............................. : FCC Part15.247 Test procedure .............................. ANSI C63.4-2003 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test............................................: Date (s) of performance of tests .............: 27 Mar. 2014 ~29 Apr. 2014 Date of Issue...........................................: 29 Apr. 2014 Test Result...............................................: Pass Testing Engineer : (Polo Cha) Technical Manager : (Brown Lu) Authorized Signatory : (Bovey Yang) Page 3 of 74 Report No.:NTEK-2014NT0327576F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 9 2.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 9 2.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 11 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3 . EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 3.1.2 TEST PROCEDURE 14 3.1.3 DEVIATION FROM TEST STANDARD 14 3.1.4 TEST SETUP 14 3.1.5 EUT OPERATING CONDITIONS 14 3.1.6 TEST RESULTS 15 3.2 RADIATED EMISSION MEASUREMENT 17 3.2.1 RADIATED EMISSION LIMITS 17 3.2.2 TEST PROCEDURE 18 3.2.3 DEVIATION FROM TEST STANDARD 18 3.2.4 TEST SETUP 19 3.2.5 EUT OPERATING CONDITIONS 20 3.2.6 TEST RESULTS 21 4 . NUMBER OF HOPPING CHANNEL 32 4.1 APPLIED PROCEDURES / LIMIT 32 4.1.1 TEST PROCEDURE 32 4.1.2 DEVIATION FROM STANDARD 32 4.1.3 TEST SETUP 32 4.1.4 EUT OPERATION CONDITIONS 32 4.1.5 TEST RESULTS 33 5 . AVERAGE TIME OF OCCUPANCY 34 5.1 APPLIED PROCEDURES / LIMIT 34 5.1.1 TEST PROCEDURE 34 5.1.2 DEVIATION FROM STANDARD 34 Page 4 of 74 Report No.:NTEK-2014NT0327576F Table of Contents Page 5.1.3 TEST SETUP 35 5.1.4 EUT OPERATION CONDITIONS 35 5.1.5 TEST RESULTS 36 6 . HOPPING CHANNEL SEPARATION MEASUREMENT 42 6.1 APPLIED PROCEDURES / LIMIT 42 6.1.1 TEST PROCEDURE 42 6.1.2 DEVIATION FROM STANDARD 42 6.1.3 TEST SETUP 42 6.1.4 EUT OPERATION CONDITIONS 42 6.1.5 TEST RESULTS 43 7 . BANDWIDTH TEST 49 7.1 APPLIED PROCEDURES / LIMIT 49 7.1.1 TEST PROCEDURE 49 7.1.2 DEVIATION FROM STANDARD 49 7.1.3 TEST SETUP 49 7.1.4 EUT OPERATION CONDITIONS 49 7.1.5 TEST RESULTS 50 8 . PEAK OUTPUT POWER TEST 56 8.1 APPLIED PROCEDURES / LIMIT 56 8.1.1 TEST PROCEDURE 56 8.1.2 DEVIATION FROM STANDARD 56 8.1.3 TEST SETUP 56 8.1.4 EUT OPERATION CONDITIONS 56 8.1.5 TEST RESULTS 57 9 . 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE 63 9.1 DEVIATION FROM STANDARD 63 9.2 TEST SETUP 63 9.3 EUT OPERATION CONDITIONS 63 9.4 TEST RESULTS 64 10 . ANTENNA REQUIREMENT 72 10.1 STANDARD REQUIREMENT 72 10.2 EUT ANTENNA 72 11 . EUT TEST PHOTO 73 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 74 Report No.:NTEK-2014NT0327576F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247(a)(1) Hopping Channel Separation PASS 15.247(b)(1) Peak Output Power PASS 15.247(c) Radiated Spurious Emission PASS 15.247(a)(iii) Number of Hopping Frequency PASS 15.247(a)(iii) Dwell Time PASS 15.247(a)(1) Bandwidth PASS 15.205 Band Edge Emission PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Page 6 of 74 Report No.:NTEK-2014NT0327576F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 74 Report No.:NTEK-2014NT0327576F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Bluetooth Stereo Clock radio speaker Trade Name Westclox Model Name 81013 Serial Model 81013cn,A9,A9L Model Difference All the models are the same circuit and RF module, except the mode names and colours. …

Text truncated - open the document above for the full version.

Page 73 of 74 Report No.:NTEK-2014NT0327576F 11. EUT TEST PHOTO Radiated Measurement Photos Page 74 of 74 Report No.:NTEK-2014NT0327576F CONDUCTED EMISSION Photos