2AATL-6233BUUBWIFI/Bluetooth MODULE

FN-LINK TECHNOLOGY LIMITED 1 PRODUCT SPECIFICATION 6233B-UUB Wi-Fi Dual-band 1T1R 802.11a/b/g/n + Bluetooth 5.2 Combo Module Version:v1.0 Customer : Customer P/N : Signature : Date : Office: 14th floor, Block B, phoenix zhigu, Xixiang Street, Baoan District, Shenzhen Factory: NO.8, Litong RD., Liuyang Economic & Technical Development Zone, Changsha, CHINA TEL:+86-755-2955-8186 Website:www.fn-link.com FN-LINK TECHNOLOGY LIMITED 2 6233B-UUB Module Datasheet Target Power: 2.4G ： 17/15/14 5.8G ： 15/14 Ordering Information Part NO. Description FG6233BUUB-00 RTL8733BU-CG/802.11a/b/g/n/ WiFi+BT5.2, 1T1R, 13*15 ,USB, two-ANT, with shielding 6233BUUB FN-LINK TECHNOLOGY LIMITED 3 CONTENTS 1. General Description ..................................................................................................5 1.1 Introduction ............................................................................................................5 1.2 Description .............................................................................................................5 2. Features......................................................................................................................6 3. Block Diagram ...........................................................................................................6 4. General Specification ................................................................................................7 4.1 WI-FI 2.4GHz RF Specification ..............................................................................7 4.2 WI-FI 5GHz RF Specification .................................................................................7 4.3 Bluetooth Specification...........................................................................................9 5. ID setting information.............................................................................................. 10 6. Pin Definition ........................................................................................................... 10 6.1 Pin Outline ........................................................................................................... 10 6.2 Pin Definition details ............................................................................................ 10 7. Electrical Specifications ......................................................................................... 12 7.1 Power Supply DC Characteristics ........................................................................ 12 7.2 Interface Circuit time series .................................................................................. 12 7. 2.1 USB Bus Timing during Power On Sequence ......................................................... 12 7.2.2 Power off by 3.3V power sequence ......................................................................... 13 8. Size reference .......................................................................................................... 13 8.1 Module Picture ..................................................................................................... 13 8.2 Marking Description ............................................................................................. 14 8.3 Physical Dimensions ............................................................................................ 14 8.4 Layout Recommendation ..................................................................................... 15 9. The Key Material List ............................................................................................... 15 10. Reference Design .................................................................................................. 16 11. Recommended Reflow Profile .............................................................................. 16 12. RoHS compliance .................................................................................................. 16 13. Package .................................................................................................................. 17 13.1 Reel.................................................................................................................... 17 13.2 Carrier Tape Detail ............................................................................................. 17 13.3 Packaging Detail ................................................................................................ 18 14. Moisture sensitivity ............................................................................................... 18 6233BUUB FN-LINK TECHNOLOGY LIMITED 4 Revision History Version Date Contents of Revision Change Preparde Checked Approved V1.0 2022/10/27 New version LTK LTK QJP 6233BUUB FN-LINK TECHNOLOGY LIMITED 5 1. General Description 1.1 Introduction 6233BUUB is a highly integrated module with Realtek 8733BU-CG single-chip 802.11a/b/g/n 1T1R WLAN, and an integrated Bluetooth 5.2 combo chip with USB 2.0 multi-function. The highly integrated module makes the possibilities of web browsing,VoIP, video stream applications. With seamless roaming capabilities and advanced security, also could interact with different vendors’802.11a/b/g/n 1x1 Access Points in the wireless LAN. The wireless module complies with IEEE 802.11 a/b/g/n standard and it can achieve up to a speed of 150Mbps when using 40MHz bandwidth. The integrated module provides USB2.0 interface for Wi-Fi. 1.2 Description Model Name 6233BUUB Product Description Support Wi-Fi/Bluetooth functionalities Dimension L x W x H: 13 x 15 x2.3 (typical) mm Wi-Fi Interface Support USB 2.0 BT Interface USB2.0 Operating temperature -20°C to 70°C Storage temperature -40°C to 85°C 6233BUUB FN-LINK TECHNOLOGY LIMITED 6 2. Features General 802.11a/b/g/n 1T1R WLAN and Bluetooth 5.2 combo chip Complete 802.11n solution for both 2.4GHz and 5GHz band 72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHz bandwidth 150Mbps receive PHY rate and 150M…

Text truncated - open the document above for the full version.

FN-LINK TECHNOLOGY LIMITED 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: FN-LINK TECHNOLOGY LIMITED Address: No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, China Product Name: WIFI/Bluetooth MODULE FCC ID: 2AATL-6233BUUB Model(s): 6233BUUB 2.911(d)(5)(i) Equipment Type We, FN-LINK TECHNOLOGY LIMITED certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Jim Hu Date: 11/3/2023 Title: General Manager Company name: FN-LINK TECHNOLOGY LIMITED NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

FN-LINK TECHNOLOGY LIMITED 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: FN-LINK TECHNOLOGY LIMITED Address: No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, China Product Name: WIFI/Bluetooth MODULE FCC ID: 2AATL-6233BUUB Model(s): 6233BUUB 2.911(d)(5)(ii) Applicant filing We, [FN-LINK TECHNOLOGY LIMITED] certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Jim Hu Date: 11/3/2023 Title: General Manager Company name: FN-LINK TECHNOLOGY LIMITED NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

FN-LINK TECHNOLOGY LIMITED * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 11/3/2023 ATTN.: Reviewing Engineer FCC ID: 2AATL-6233BUUB FRN No.: 0022902761 Per section 2.911(d)(7) of the FCC rules, FN-LINK TECHNOLOGY LIMITED certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: JOC Australia Inc Physical U.S. Company Address: 18351 Colima Road Ste 585 Rowland Heights, California, 91748 United States of America Agent contact name/Title : Benjamin. Smith/Vice President Agent Email Address: [email protected]/[email protected] Tel No.: +1(626) 341 3408 FRN No.: 0033379421 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Agent Signed (if different to Applicant): Signed: Signed: Printed name: Jim Hu Printed name: Benjamin. Smith Title: Manager Title: Vice President Company Name: FN-LINK TECHNOLOGY LIMITED Company Name: JOC Australia Inc Date: 11/3/2023 Date: 11/3/2023

FN-LINK TECHNOLOGY LIMITED Authorization November 3, 2023 Company name: FN-LINK TECHNOLOGY LIMITED Address: No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, China Product Name: WIFI/Bluetooth MODULE FCC ID: 2AATL-6233BUUB Model(s): 6233BUUB We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Name Jim Hu Position Manager Company Name FN-LINK TECHNOLOGY LIMITED Address No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, CHINA Tel +8613538178944 Fax / Email [email protected]

FN-LINK TECHNOLOGY LIMITED Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023-11-03 Subject; Request for Long Term Confidentiality FCC ID: 2AATL-6233BUUB To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram BOM Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: November 3, 2023 Name Jim Hu Position Manager Company Name FN-LINK TECHNOLOGY LIMITED Address No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, CHINA Tel +8613538178944 Fax / Email [email protected]

FN-LINK TECHNOLOGY LIMITED Letter of Authorization Company: FN-LINK TECHNOLOGY LIMITED Address: No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, China Product Name: WIFI/Bluetooth MODULE Model Number(s): 6233BUUB We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: November 3, 2023 Name Jim Hu Position Manager Company Name FN-LINK TECHNOLOGY LIMITED Address No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, CHINA Tel +8613538178944 Fax / Email [email protected]

FCC Modular Approval Request To the FCC or FCC TCB handling this application Hereby we, Company (grantee) FN-LINK TECHNOLOGY LIMITED Addresss No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, CHINA City / ZIP / State / Country China request modular approval for the certification of our equipment within this application, identified by: FCC ID: 2AATL-6233BUUB The table below contains justification for modular approval of this equipment. Requirement per DA 00-1407 Explanation from grantee 1. The modular transmitter must have its own RF shielding. Has RF shielding. 2.The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular have buffered modulation/data inputs. 3. The modular transmitter must have its own power supply regulation. The modular transmitter have its own power supply regulation. 4.The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. This module is equipped with a PCB antenna, please refer to the External Photo for the detail. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. The module was tested in a stand-alone configuration, please refer to the Setup Photo for the detail 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: ??????????” or “Contains FCC ID: 2ATCG-BB810QI4A” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. Please refer to label sample exhibit - host labeling is described in integration manual 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The required FCC rule has been fulfilled and all the instructions for the maintaining compliance have been clearly stated in the User Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimetre wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. The MPE evaluation with 20cm distance restriction is submitted for the compliance of RF Exposure requirement. Attestation (by grantee) City and Country: Date: Name: (this must be a person) Function: Signature: (or official company stamp) Changsha, Hunan, CHINA November 9, 2023 Jim Hu Manager

FCC ID: 2AATL-6233BUUB 5G WIFI&BT ANT 2.4G WIFI ANT FCC ID: 2AATL-6233BUUB FCC ID: 2AATL-6233BUUB FCC ID: 2AATL-6233BUUB

0.8*0.2cm Label Location FCC ID: 2AATL-6233BUUB

FCC ID: 2AATL-6233BUUB FCC ID: 2AATL-6233BUUB

FCC ID: 2AATL-6233BUUB Prediction of MPE at a given distance 1. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) 2. Test Procedure Equation from page 18 of OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to the antenna G = numeric gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the centre of radiation of the antenna FCC ID: 2AATL-6233BUUB 3. Result Mode Frequency (MHz) Prediction distance (cm) Max Tune up power MPE (mW/cm 2 ) Limit (mW/cm 2 ) SAR Test Exclusion dBm mW BT EDR 2402-2480 20 8 6.3096 0.0027 1 Yes BT LE 2402-2480 20 4 2.5119 0.0011 1 Yes 2.4G WIFI 2412-2462 20 20 100.0000 0.0430 1 Yes 5G WIFI B1 5180-5240 20 20 100.0000 0.0568 1 Yes 5G WIFI B2 5260-5320 20 20 100.0000 0.0568 1 Yes 5G WIFI B3 5500-5700 20 20 100.0000 0.0568 1 Yes 5G WIFI B4 5745-5825 20 20 100.0000 0.0568 1 Yes Maximum Simultaneous transmission MPE Ratios for BT+WIFI Max MPE Ratio BT /Limit Max MPE ratio WIFI /Limit ∑MPE ratios Limit Result 0.0027 0.0568 0.0595 1 PASS BT/2.4GWiFi Antenna Gain: Rob Antenna, max gain 3.35dBi, 2.16(numeric) 5G WIFI Antenna Gain: Rob Antenna, max gain 4.56dBi, 2.86(numeric) The antenna MIMO combining gain is 7.56dBi. 5.71(numeric) Then SAR evaluation is not required.

ALPHA's reports is using a digital certificate that is trusted on Adobe's official server. If there is no digital certificate or the digital certificate shows damaged in your report. Please do not accept the report. E-mail: [email protected] Tel: 4008-3008-95 Website: http://www.a-lab.cn FCC TEST REPORT FCC ID: 2AATL-6233BUUB On Behalf of FN-LINK TECHNOLOGY LIMITED WIFI/Bluetooth MODULE Model No.: 6233BUUB Prepared for : FN-LINK TECHNOLOGY LIMITED Address : No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, China Prepared By : Shenzhen Alpha Product Testing Co., Ltd. Address : Building i, No.2, Lixin Road, Fuyong Street, Bao’an District, 518103, Shenzhen, Guangdong, China Report Number : A2305037-C01-R02 Date of Receipt : May 22, 2023 Date of Test : May 22, 2023-October 18, 2023 Date of Report : November 2, 2023 Version Number : V0 Page 2 of 47 Report No.: A2305037-C01-R02 TABLE OF CONTENTS Description Page 1. Summary of Standards And Results -------------------------------------------------------------------------------- 5 1.1. Description of Standards and Results ------------------------------------------------------------------------ 5 2. General Information ------------------------------------------------------------------------------------------------------ 6 2.1. Description of Device (EUT) ------------------------------------------------------------------------------------ 6 2.2. Accessories of Device (EUT) ----------------------------------------------------------------------------------- 7 2.3. Tested Supporting System Details----------------------------------------------------------------------------- 7 2.4. Block Diagram of connection between EUT and simulators -------------------------------------------- 7 2.5. Test Mode Description -------------------------------------------------------------------------------------------- 7 2.6. Test Conditions ----------------------------------------------------------------------------------------------------- 8 2.7. Test Facility ---------------------------------------------------------------------------------------------------------- 8 2.8. Measurement Uncertainty --------------------------------------------------------------------------------------- 8 2.9. Test Equipment List ----------------------------------------------------------------------------------------------- 9 3. Spurious Emission ------------------------------------------------------------------------------------------------------- 10 3.1. Test Limits ---------------------------------------------------------------------------------------------------------- 10 3.2. Test Procedure ---------------------------------------------------------------------------------------------------- 10 3.3. Test Setup ---------------------------------------------------------------------------------------------------------- 11 3.4. Test Results -------------------------------------------------------------------------------------------------------- 12 4. Power Line Conducted Emission ----------------------------------------------------------------------------------- 23 4.1. Test Limits ---------------------------------------------------------------------------------------------------------- 23 4.2. Test Procedure ---------------------------------------------------------------------------------------------------- 23 4.3. Test Setup ---------------------------------------------------------------------------------------------------------- 23 4.4. Test Results -------------------------------------------------------------------------------------------------------- 23 5. Conducted Maximum Output Power ------------------------------------------------------------------------------- 26 5.1. Test limits ----------------------------------------------------------------------------------------------------------- 26 5.2. Test Procedure ---------------------------------------------------------------------------------------------------- 26 5.3. Test Setup ---------------------------------------------------------------------------------------------------------- 26 5.4. Test Results -------------------------------------------------------------------------------------------------------- 26 6. Peak Power Spectral Density ----------------------------------------------------------------------------------------- 27 6.1. Test limits ----------------------------------------------------------------------------------------------------------- 27 6.2. Test Procedure ---------------------------------------------------------------------------------------------------- 27 6.3. Test Setup ---------------------------------------------------------------------------------------------------------- 27 6.4. Test Results -------------------------------------------------------------------------------------------------------- 27 7. Bandwidth ------------------------------------------------------------------------------------------------------------------ 31 7.1. Test limits ----------------------------------------------------------------------------------------------------------- 31 7.2. Test Procedure ---------------------------------------------------------------------------------------------------- 31 7.3. Test Setup ---------------------------------------------------------------------------------------------------------- 31 7.4. Test Results -------------------------------------------------------------------------------------------------------- 31 8. Band Edge Check -------------------------------------------------------------------------------------------------------- 39 8.1. Test limits ----------------------------------------------------------------------------------------------------------- 39 8.2. Test Procedure ---------------------------------------------------------------------------------------------------- 39 8.3. Test Setup -----------------------------------------------------------------------…

Text truncated - open the document above for the full version.

ALPHA's reports is using a digital certificate that is trusted on Adobe's official server. If there is no digital certificate or the digital certificate shows damaged in your report. Please do not accept the report. E-mail: [email protected] Tel: 4008-3008-95 Website: http://www.a-lab.cn FCC TEST REPORT FCC ID: 2AATL-6233BUUB On Behalf of FN-LINK TECHNOLOGY LIMITED WIFI/Bluetooth MODULE Model No.: 6233BUUB Prepared for : FN-LINK TECHNOLOGY LIMITED Address : No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, China Prepared By : Shenzhen Alpha Product Testing Co., Ltd. Address : Building i, No.2, Lixin Road, Fuyong Street, Bao’an District, 518103, Shenzhen, Guangdong, China Report Number : A2305037-C01-R03 Date of Receipt : May 22, 2023 Date of Test : May 22, 2023-October 18, 2023 Date of Report : November 2, 2023 Version Number : V0 Page 2 of 71 Report No.: A2305037-C01-R03 TABLE OF CONTENTS Description Page 1. Summary of Standards And Results ----------------------------------------------------------------------------------- 5 1.1. Description of Standards and Results --------------------------------------------------------------------------- 5 2. General Information --------------------------------------------------------------------------------------------------------- 6 2.1. Description of Device (EUT) --------------------------------------------------------------------------------------- 6 2.2. Accessories of Device (EUT) -------------------------------------------------------------------------------------- 7 2.3. Tested Supporting System Details ------------------------------------------------------------------------------- 7 2.4. Block Diagram of connection between EUT and simulators ----------------------------------------------- 7 2.5. Test Mode Description ----------------------------------------------------------------------------------------------- 8 2.6. Test Conditions -------------------------------------------------------------------------------------------------------- 9 2.7. Test Facility ------------------------------------------------------------------------------------------------------------- 9 2.8. Measurement Uncertainty ------------------------------------------------------------------------------------------ 9 2.9. Test Equipment List ------------------------------------------------------------------------------------------------ 10 3. Spurious Emission --------------------------------------------------------------------------------------------------------- 11 3.1. Test Limits ------------------------------------------------------------------------------------------------------------ 11 3.2. Test Procedure ------------------------------------------------------------------------------------------------------ 12 3.3. Test Setup ------------------------------------------------------------------------------------------------------------ 12 3.4. Test Results ---------------------------------------------------------------------------------------------------------- 13 4. Power line Conducted Emission -------------------------------------------------------------------------------------- 32 4.1. Test Limits ------------------------------------------------------------------------------------------------------------ 32 4.2. Test Procedure ------------------------------------------------------------------------------------------------------ 32 4.3. Test Setup ------------------------------------------------------------------------------------------------------------ 32 4.4. Test Results ---------------------------------------------------------------------------------------------------------- 32 5. Conducted Maximum Output Power --------------------------------------------------------------------------------- 35 5.1. Test limits ------------------------------------------------------------------------------------------------------------- 35 5.2. Test Procedure ------------------------------------------------------------------------------------------------------ 35 5.3. Test Setup ------------------------------------------------------------…

Text truncated - open the document above for the full version.