2AATL-F88EUUD15USB WIFI Dongle

FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 1 /12 3/18/2014 F88EUUD15-B3 series user 's manual FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 2 /12 3/18/2014 Index How to install the driver Put the product plug into the USB port of PC..........................3 Copy the driver into the PC....................................................3 Install the driver...................................................................4 Install driver successfully..........................................................4 connect to external wireless network........................................6 How to set the device to “access point mode” Set to “access point mode”.....................................................9 Setting internet connection share...........................................11 Connect to the access and surf the Internet............................12 FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 3 /12 3/18/2014 1. Put the product plug into the USB port, the "device manager" of PC is shown below: 2. Copy the corresponding driver "RTLWlanU_WindowsDriver_1019.0.0518.2012_ UI_1.00.0191_EU" into the PC, and install driver, the installation methods: open the file "RTLWlanU_WindowsDriver_1019.0.0518.2012_UI_1.00.0191_EU", double click "Setup" installation program, guide to install. FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 4 /12 3/18/2014 3. After install driver successfully. the "device manager" of PC is shown below: FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 5 /12 3/18/2014 The USB icon and wireless network adapter displaying in the lower right of the screen. Shown as below: FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 6 /12 3/18/2014 4. The default settings is "station mode", we can connect to external wireless network. (i.e. it is regarded as a wireless adapter) FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 7 /12 3/18/2014 5. Set the device to “access point mode” (1). Click the device icon “” on the lower right of the screen. It will display “REALTEK 11n USB Wireless LAN Utility” configuration interface. (2). Click on the "mode" button, then select "access points", the screen appears "Switching from station to AP mode...", then enter the "access point mode", and the lower right of the screen will show "access points" icon. FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 8 /12 3/18/2014 FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 9 /12 3/18/2014 At the same time also shows the name of the access point in the "REALTEK 11n USB Wireless LAN Utility" configuration interface, the default no secret key, as shown below: FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 10 /12 3/18/2014 (3).Right now. Switch mode successfully, then select "Setting Internet Connection Sharing(ICS)", as shown below: FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 11 /12 3/18/2014 (4). After select " Setting Internet Connection Sharing(ICS)", as shown below: FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 12 /12 3/18/2014 (5).It can be connected to the access by mobile phone or other mobile device to surf the Internet. FCC ID: 2AATL-F88EUUD15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

FN-LINK TECHNOLOGY LIMITED Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Confidentiality Company name: FN-LINK TECHNOLOGY LIMITED FCC ID : 2AATL-F88EUUD15 FCC Part 15 Certification Gentlemen, Pursuant to 47 CFR 0.457(d)(1)(ii) and 0.459 we hereby requests permanent confidentiality of the following documents for the subject application: Exhibit Type Description ☒ Schematics All circuitry of devices and component values ☒ Block Diagrams Details of device showing the frequency of all oscillators ☒ Operational Description Description of the circuit functions ☒ Tune Up Note: Exhibit types that are commonly held confidential are: (1) Schematics, (2) Block Diagrams, (3) Bill Of Materials, (4) Operational Descriptions. Any exhibit NOT granted confidentiality is viewable on the FCC website as soon as a grant is issued. These documents contain detailed system and equipment description and related information about the product which we considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, we consider that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours sincerely, Signatory Name Anne Xu Position Manager Company Name FN-LINK TECHNOLOGY LIMITED Address 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao’an District, Shenzhen City, China Tel 075529558186 Email [email protected]

FN-LINK TECHNOLOGY LIMITED Date: 13.03.2014 Authority to Act as an Agent We declare that the following representative (agent) Name Mark Zhu Position Manager Company Name Shenzhen Certification Technology Service Co., Ltd. Address 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2 nd Road, Bao’an District, Shenzhen 518126, P.R. China Tel / Fax 0755-86375541/0755-26736857 Email [email protected] to act on our behalf on all matters concerning the application and documents submitted to PHOENIX TEST-LAB for product certification below Product Name USB WIFI Dongle Model Name F88EUUD15-B1, F88EUUD15-B2, F88EUUD15-B3, F88ETUD15-B1, F88ETUD15-B2, F88ETUD15-B3 Brand Name . Yours sincerely, Signatory Name Anne Xu Position Manager Company Name FN-LINK TECHNOLOGY LIMITED Address 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao’an District, Shenzhen City, China Tel 075529558186 Email [email protected] In case of FCC, we certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance.

Ersteller: D. Brandhorst Revision: 00 Erstelldatum: 21.06.07 Datum: 00.00.00 Seite 1 von 1 FN-LINK TECHNOLOGY LIMITED Date: 3/13/2014 Subject: Ad Hoc Mode Function Declaration FCC ID: 2AATL-F88EUUD15 To Whom it may concern, This device is acting as slave and operating in 2412-2462MHz band. Ad Hoc function is supported but not able to operate on non-US frequencies. Please contact the one signed below or the authorized agent for this filing. Thank you. Regards, Signatory (YOUR CONTACT DETAILS) Name : Anne Xu Position : Manager Company: FN-LINK TECHNOLOGY LIMITED Adress : 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao’an District, Shenzhen City, China Tel. : 075529558186 Email : [email protected]

Label Location

15mm 6mm USB WIFI Dongle Model: F88EUUD15-B3 FCC ID：2AATL- F88EUUD15 FN-LINK TECHNOLOGY LIMITED

Antenna

FCC ID: 2AATL-F88EUUD15 RF EXPOSURE TEST FCC ID: 2AATL-F88EUUD15 SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation17  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. FCC ID: 2AATL-F88EUUD15 For tune up: IEEE802.11 b, 8.8dbm±1 IEEE802.11 g, 8.8dbm±1 IEEE802.11 n/HT20. 8dbm±1 IEEE802.11 n/HT40. 7dbm±1 The max.output power E.I.R.P is 9.8dBm=9.55mW, Frequency is 2.462GHz So (9.55/5)* √2.462=2.997≤ 3.0 Note: √2.462 =1.569 Conclusion: No SAR is required. Maximum measured transmitter power. Mode Frequency (MHz) Maximum Peak Conducted Output Power (dBm) Maximum Conducted Output Power (mW) CH1: 2412 9.63 9.18 CH6: 2437 9.45 8.81 IEEE 802.11 b CH11: 2462 9.37 8.65 CH1: 2412 9.21 8.34 CH6: 2437 8.99 7.93 IEEE 802.11 g CH11: 2462 8.92 7.80 CH1: 2412 8.64 7.31 CH6: 2437 8.53 7.13 IEEE 802.11 n/HT20 CH11: 2462 8.46 7.01 CH1: 2422 7.25 5.31 CH4: 2437 7.17 5.21 IEEE 802.11 n/HT40 CH7: 2452 7.52 5.65 Note: The Antenna max gain is 0 dBi, so the max E.I.R.P is 9.63dBm(9.18mW). The max.output power E.I.R.P is 9.63dBm=9.18mW, Frequency is 2.412GHz So (9.18/5)* √2.412=2.85≤ 3.0 Note: √2.412 =1.553 Conclusion: No SAR is required.

Shenzhen Certification Technology Service Co., Ltd 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2nd Road, Bao'an District, Shenzhen 518126, P.R. China. FCC ID: 2AATL- F88EUUD15 Page 1 of 74 TEST REPORT FCC ID: 2AATL-F88EUUD15 Applicant : FN-LINK TECHNOLOGY LIMITED Address : 5 th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao’an District, Shenzhen City, China Equipment under Test (EUT): Name : USB WIFI Dongle Model : F88EUUD15-B1, F88EUUD15-B2, F88EUUD15-B3, F88ETUD15-B1, F88ETUD15-B2, F88ETUD15-B3 Standards : FCC PART 15, SUBPART C : 2013 (Section 15.247) Report No. : CST-TCB140212005 Date of Test : February 23-March 03, 2014 Date of Issue : March 05, 2014 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above Authorized Signature (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Certification Technology Service Co., Ltd. Or test done by Shenzhen Certification Technology Service Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Certification Technology Service Co., Ltd. Approvals in writing. Report No.: CST-TCB140212005 FCC ID: 2AATL- F88EUUD15 Page 2 of 74 TABLE OF CONTENT Description Page 1 General Information--------------------------------------------------------------------------------------4 1.1 Description of Device (EUT)---------------------------------------------------------------------4 1.2 Description of Test Facility-----------------------------------------------------------------------4 2 EMC Equipment List--------------------------------------------------------------------------------------4 3 Test Procedure---------------------------------------------------------------------------------------------4 4 Summary of Measurement---------------------------------------------------------------------------4 4.1 Summary of test result-----------------------------------------------------------------------------4 4.2 Test connection-------------------------------------------------------------------------------------4 4.3 Assistant equipment used for test----------------------------------------------------------------4 4.4 Test mode--------------------------------------------------------------------------------------------4 4.5 Channel list------------------------------------------------------------------------------------------4 4.6 Test Conditions-------------------------------------------------------------------------------------4 4.7 Measurement Uncertainty (95% confidence levels, k=2)-------------------------------------4 5 Spurious Emission-------------------------------------------------------------------------------------4 5.1 Radiation Emission---------------------------------------------------------------------------------4 5.1.1 Radiation Emission Limits(15.209)--------------------------------------------------------------4 5.1.2 Test Setup--------------------------------------------------------------------------------------------4 5.1.3 Test Procedure--------------------------------------------------------------------------------------4 5.1.4 Test Equipment Setting For emission test Result----------------------------------------------4 5.1.5 Test Condition--------------------------------------------------------------------------------------4 5.1.6 Test Result-------------------------------------------------------------------------------------------4 6 POWER LINE CONDUCTED EMISSION---------------------------------------------------------4 6.1 Conducted Emission Limits(15.207)------------------------------------------------------------4 6.2 Test Setup--------------------------------------------------------------------------------------------4 6.3 Test Procedure--------------------------------------------------------------------------------------4 6.4 Test Results------------------------------------------------------------------------------------------4 7 Conducted Maximum Output Power-------------------------------------------------------------4 7.1 Test limit---------------------------------------------------------------------------------------------4 7.2 Test Procedure--------------------------------------------------------------------------------------4 7.3 Test Setup--------------------------------------------------------------------------------------------4 7.4 Test Results------------------------------------------------------------------------------------------4 8 PEAK POWER SPECTRAL DENSITY-------------------------------------------------------------4 8.1 Test limit---------------------------------------------------------------------------------------------4 8.1.1 Please refer section15.247.-----------------------------------------------------------------------4 8.2 Method of measurement---------------------------------------------------------------------------4 8.3 Test Setup--------------------------------------------------------------------------------------------4 8.4 Test Results------------------------------------------------------------------------------------------4 9 Bandwidth-------------------------------------------------------------------------------------------------4 9.1 Test limit---------------------------------------------------------------------------------------------4 9.2 Method of measurement---------------------------------------------------------------------------4 9.3 Test Setup--------------------------------------------------------------------------------------------4 9.4 Test Results--------------------------------------------------------------------------------…

Text truncated - open the document above for the full version.

Photographs-Radiated Emission Test Setup in Chamber Below 1G Above 1G Photographs-Conducted Emission Test Setup