2AATLFN-8126EU2.4G WiFi module

FN-LINK TECHNOLOGY LIMITED http://www.fn‐link.com Page 1 /6 8/28/2014 FN-8126EU series user 's manual FN-LINK TECHNOLOGY LIMITED http://www.fn‐link.com Page 2 /6 8/28/2014 Index How to install the driver Put the product plug into the USB port of PC..........................3 Copy the driver into the PC....................................................3 Install the driver...................................................................4 Install driver successfully..........................................................4 connect to external wireless network........................................6 FN-LINK TECHNOLOGY LIMITED http://www.fn‐link.com Page 3 /6 8/28/2014 1. Put the product plug into the USB port, the "device manager" of PC is shown below: 2. Copy the corresponding driver "RTLWlanU_WindowsDriver_1019.0.0518.2012_ UI_1.00.0191_EU" into the PC, and install driver, the installation methods: open the file "RTLWlanU_WindowsDriver_1019.0.0518.2012_UI_1.00.0191_EU", double click "Setup" installation program, guide to install. FN-LINK TECHNOLOGY LIMITED http://www.fn‐link.com Page 4 /6 8/28/2014 3. After install driver successfully. the "device manager" of PC is shown below: FN-LINK TECHNOLOGY LIMITED http://www.fn‐link.com Page 5 /6 8/28/2014 The USB icon and wireless network adapter displaying in the lower right of the screen. Shown as below: FN-LINK TECHNOLOGY LIMITED http://www.fn‐link.com Page 6 /6 8/28/2014 4. The default settings is "station mode", we can connect to external wireless network. (i.e. it is regarded as a wireless adapter) FCC Statement: The final end product must be labeled in a visible area with the following "Contains TX FCC ID:2AATLFN-8126EU". If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 stayement is required to be availale in the users manual: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement: This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to missing shielding the module is strictly limited to integration by the Grantee himself or his dedicated OEM integrator under control of the Grantee.However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. This device is intended only for OEM integrators under the following conditions: 1)This module is granted as a Limited Modular Approval. 2)This device has been designed to operate with a PCB antenna having a maximum gain of 0dBi.Only this type of antenna may be used. This device has been evaluated and shown compliant with the FCC RF Exposure limits under fixed exposure conditions (antennas are greater than 20cm from a person’s body) when installed in certain specific OEM configurations.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (current) 3.0 4.0 May-23-2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 4.0 FN-LINK TECHNOLOGY LIMITED 2014-8-27 To: SIEMIC, Inc. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, _____ FN-LINK TECHNOLOGY LIMITED _____hereby authorize SIEMIC, Inc. to act as Certification Body for certifying for the following project(s): Product description: 2.4G WiFi module FCC ID Number: 2AATLFN-8126EU model name: FN-8126EU, FN-8126ET, FN-8126B3ET, FN-8126B5ET, FN-8126W3ET, FN-8126W5ET, FN-8126B3EU, FN-8126B5EU, FN-8126W3EU, FN-8126W5EU We affirm that between SIEMIC, Inc. and _____ FN-LINK TECHNOLOGY LIMITED ___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature: Client’s name / title: Anne / Manager Contact information / address: 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 FN-LINK TECHNOLOGY LIMITED 2014-8-27 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AATLFN-8126EU We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title: Anne / Manager Contact information / address: 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District

SCS-F26 Modular Approval Letter Page 1 of 4 Rev 8.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Modular Approval Declaration Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (Obsolete) 1.0 1.0 Dec-04-2006 Added IC Modular Letter (Obsolete) 1.0 2.0 Feb 16 2009 Add LMA and MA option (Obsolete) 2.0 3.0 April 14 2010 Revised per RSS Gen issue 3.0 (Obsolete) 3.0 4.0 Jan 12 2011 Removed Foot(2) (obsolete) 4.0 5.0 July 19 2011 Adding New note per KDB996369 D01 V01R03 (obsolete) 5.0 6.0 August 29 2011 Updated company template & Added text box (obsolete) 6.0 7.0 Jan-31-2012 Updated modular requirement (current) 7.0 8.0 Sept 05 2014 SCS-F26 Modular Approval Letter Page 2 of 4 Rev 8.0 FN­LINK TECHNOLOGY LIMITED (Date) 2014/8/26 2.4G WiFi module FCC ID : 2AATLFN-8126EU , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below : Questions are: * Please provide a detailed explanation if the answer is “No.” Item Modular requirement Yes No 1 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; NO 2 The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; Yes 3 The module must contain power supply regulation on the module; Yes 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); Yes 5 The module must demonstrate compliance in a stand-alone configuration; Yes 6 The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); Yes 7 The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; Yes 8 The module must comply with RF exposure requirements Yes Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. (3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. Client’s signature Client’s name / title Anne / Manager Contact information / address 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District

Model difference letter Aug. 27, 2014 Dear Reviewer, This is a new Application from FN-LINK TECHNOLOGY LIMITED FN-8126EU, FN-8126ET, FN-8126B3ET, FN-8126B5ET, FN-8126W3ET, FN-8126W5ET, FN-8126B3EU, FN-8126B5EU, FN-8126W3EU and FN-8126W5EU are identical in interior structure, electrical circuits, components and appearance, only different in model name. Thank you for your cooperation! Yours sincerely, Signatory: Name: Anne Position: Manager Company Name: FN-LINK TECHNOLOGY LIMITED Address: 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District

Model No.: FN-8126EU FRONT VIEW OF SAMPLE BACK VIEW OF SAMPLE

FCC ID: 2AATLFN-8126EU

FCC ID Label Location

Model No.: FN-8126EU INTERNAL PHOTO OF SAMPLE INTERNAL PHOTO OF SAMPLE

FCC §15.247 (i) & §1.1307 (b) (1) & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart 15.247 (i) and subpart 1.1307 (b)(1), 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (Minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Result Calculated Formulary: Predication of MPE limit at a given distance S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW). G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain. R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Antenna Gain Conducted Power Frequency (MHz) (dBi) (numeric) (dBm) (mW) Evaluation Distance(cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) 2437 0 1 16.27 42.36 20 0.008 1 Note: To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm from nearby persons. Result: Compliance

FCC 47 CFR PART 15 SUBPART C TEST REPORT For Applicant : FN-LINK TECHNOLOGY LIMITED Address : 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao’an District, Shenzhen City,China Product Name : 2.4G WiFi module Model Name : FN-8126EU, FN-8126ET, FN-8126B3ET, FN-8126B5ET, FN-8126W3ET, FN-8126W5ET, FN-8126B3EU, FN-8126B5EU, FN-8126W3EU, FN-8126W5EU Brand Name : N/A FCC ID : 2AATLFN-8126EU Report No. : MTE/SAL/F14081093 Date of Issue : Aug. 28, 2014 Issued by : Most Technology Service Co., Ltd. Address : No.5, Langshan 2nd Rd., North Hi-Tech Industrial park, Nanshan, Shenzhen, Guangdong, China Tel : 86-755-8617 0306 Fax : 86-755-8617 0310 The report consists 79 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by MOST. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers, reviewer and approver. FCC ID: 2AATLFN-8126EU Report No.: MTE/SAL/F14081093 Page 2 of 67 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY ....................................................................................... 4 2. GENERAL INFORMATION.................................................................................................... 5 2.1 Product Information.................................................................................................................................. 5 2.2 Objective.................................................................................................................................................... 6 2.3 Test Standards and Results ..................................................................................................................... 6 2.4 Environmental Conditions........................................................................................................................ 6 2.5 MEASUREMENT UNCERTAINTY ............................................................................................................... 6 3. TEST FACILITY ..................................................................................................................... 7 3.2 Test Conditions .......................................................................................................................................... 8 3.3 Channel List................................................................................................................................................ 8 3.4 Description of Test Modes......................................................................................................................... 8 3.5 Table of Parameters of Text Software Setting.......................................................................................... 8 4. TEST EQUIPMENT LIST ....................................................................................................... 9 5. 47 CFR Part 15 C 15.247 Requirements............................................................................ 10 5.1 6dB Bandwidth ........................................................................................................................................ 10 5.1.1 Definition ......................................................................................................................................... 10 5.1.2 Limit................................................................................................................................................. 10 5.1. 3 Test Configuration............................................................................................................................ 10 5.1.4 Test Procedure.................................................................................................................................. 10 5.1.5 Test Result........................................................................................................................................ 10 5.2 Peak Output Power ................................................................................................................................. 17 5.2.1 Definition ......................................................................................................................................... 17 5.2.2 Limit................................................................................................................................................. 17 5.2.3 Test Configuration............................................................................................................................ 17 5.2.4 Test Procedure.................................................................................................................................. 17 5.2.5 Test Result........................................................................................................................................ 17 5.3 Conducted Spurious Emission .............................................................................................................. 19 5.3.1 Definition ......................................................................................................................................... 19 5.3.2 Test Description ............................................................................................................................... 19 5.3.3 Test Result........................................................................................................................................ 19 5.4 Band Edge ............................................................................................................................................... 20 5.4.1 Definition ................................................................................................................................…

Text truncated - open the document above for the full version.

Model No.: FN-8126EU RE TEST SETUP Model No.: FN-8126EU CE TEST SETUP SPURIOUS EMISSION TEST SETUP