2AAU3JET-100AWIRED BOOSTER

Jetson Transmission Booster Operating Instructions Models: JET-100A 1. Function The Jetson transmission boosters function with two JETTE brand TPMS systems for trucks. Even though the basic systems have been tested and work well up to 60 ft., there are occasions where a vehicle will emit electronic interference causing the loss of signal from the transmitters. The chance of lost signals also increases with distance (from receiver to rear tires), extreme cold and battery deterioration. 2. Operation Once installed on the tow vehicle or approximate middle of a large Motor coach, no further programming or action is necessary. The Jetson Booster will automatically pick up the signals from all transmitters and resend the information to the receiver/monitor. 3. Installation Position Although fully weather proof, it is recommended to install the booster in a relatively protected area. The illustration below shows the ideal location for RV, Caravan, trailer and truck use. PDF 文件使用 "FinePrint pdfFactory Pro" 试用版本创建 www.fineprint.com.cn 4. Installation The JET100A Jetson booster comes with several “wire ties” which may be used to secure it and its power cord wherever. Please mount as securely as possible to minimize vibration. 5. Power Supply Model JET-100A requires external DC power: DC 12V or DC 24V. Red wire is “+” positive, black wire is “-“ negative. If uncertain, contact a local repair facility to help install the unit. 6. Technical Data: Working Temperature -40~85°C (-40°F to 185°F) Working Voltage DC 12V~DC 24V Working Frequency 434.2 MHZ 7. Warrantee: Jetson boosters are guaranteed against manufacturing defects for a period of one year from date of purchase. PDF 文件使用 "FinePrint pdfFactory Pro" 试用版本创建 www.fineprint.com.cn FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Shenzhen Jetson Electronic Technologies Co.,Ltd Model Difference FCC ID: 2AAU3JET-100A Model : JET-100A ,TT-100A、BS101,TMB100-W All the models are the same circuit and RF module, except the mode names. Regards, Client’s signature Signature Name: May Lee Title: Manager Address: Rm1108 East Block 4，Seg sci-tech park，North Huaqiang Road， shenzhen 518031 China

Shenzhen Jetson Electronic Technologies Co.,Ltd SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 Shenzhen Jetson Electronic Technologies Co.,Ltd SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 2013/8/22 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, Shenzhen Jetson Electronic Technologies Co.,Ltd hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product： WIRED BOOSTER Trade Name： JETSON Model Name： JET-100A Serial Model： TT-100A,BS101,TMB100-W FCC ID : 2AAU3JET-100A We affirm that between SIEMIC and Shenzhen Jetson Electronic Technologies Co.,Ltd , any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Signature Name: May Lee Title: Manager Address: Rm1108 East Block 4，Seg sci-tech park，North Huaqiang Road，shenzhen 518031 China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Shenzhen Jetson Electronic Technologies Co.,Ltd 2013-8-22 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AAU3JET-100A We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Signature Name: May Lee Title: Manager Address: Rm1108 East Block 4，Seg sci-tech park，North Huaqiang Road，shenzhen 518031 China

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8

FCC ID LABELING AND LOCATION FCC ID Label WIRED BOOSTER Model NO.：JET-100A JETSON Input: DC12V--DC36V FCC ID: 2AAU3JET-100A Shenzhen Jetson Electronic Technologies Co.,Ltd Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 ANT ANT Photo 3 Photo 4

FCC RADIO TEST REPORT FCC ID: 2AAU3JET-100A Product： WIRED BOOSTER Trade Name： JETSON Model Name： JET-100A Serial Model： TT-100A,BS101,TMB100-W Report No.： NTEK-2013NT0730854F Prepared for Shenzhen Jetson Electronic Technologies Co.,Ltd Rm1108 East Block 4，Seg sci-tech park，North Huaqiang Road，shenzhen 518031 China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 25 Report No.: NTEK-2013NT0730854F ` TEST RESULT CERTIFICATION Applicant’s name................. : Shenzhen Jetson Electronic Technologies Co.,Ltd Address ................................. : Rm1108 East Block 4，Seg sci-tech park，North Huaqiang Road， shenzhen 518031 China Manufacture's Name............ : Shenzhen Jetson Electronic Co.,Ltd Address ................................. : 6/F，Block A，Jjingdingsheng Industirial Park Qinghua Road， Bao’an District ，Shenzhen 51809 China Product description Product name ........................... : WIRED BOOSTER Model and/or type reference : JET-100A Serial Model： TT-100A,BS101,TMB100-W Standards............................. : FCC Part15.231 Test procedure .............................. ANSI C63.4-2003 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test............................................: Date (s) of performance of tests .............: 30 Jul. 2013 ~14 Aug. 2013 Date of Issue...........................................: 14 Aug. 2013 Test Result...............................................: Pass Testing Engineer : (Polo Cha) Technical Manager : (Brown Lu) Authorized Signatory : (Bovey Yang) Page 3 of 25 Report No.: NTEK-2013NT0730854F ` Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 9 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 3 . ANTENNA REQUIREMENT 11 3.1 STANDARD REQUIREMENT 11 3.2 EUT ANTENNA 11 3.3 CONDUCTED EMISSION MEASUREMENT 12 3.3.1 POWER LINE CONDUCTED EMISSION LIMITS 12 3.3.2 TEST PROCEDURE 13 3.3.3 DEVIATION FROM TEST STANDARD 13 3.3.4 TEST SETUP 13 3.2.5 TEST RESULT 14 3.4 RADIATED EMISSION MEASUREMENT 15 3.4.1 RADIATED EMISSION LIMITS 15 3.4.2 TEST PROCEDURE 16 3.4.3 DEVIATION FROM TEST STANDARD 16 3.4.4 TEST SETUP 17 3.4.5 TEST RESULTS (BELOW 30MHZ) 19 3.4.6 TEST RESULTS (BETWEEN 30 – 1000 MHZ) 20 4 . BANDWIDTH TEST 22 4.1 TEST PROCEDURE 22 4.2 DEVIATION FROM STANDARD 22 4.3 TEST SETUP 22 4.4 TEST RESULTS 23 5 . TRANSMITTER TIMEOUT 24 5.1 REQUIREMENTS 24 6 . EUT TEST PHOTO 25 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 4 of 25 Report No.: NTEK-2013NT0730854F ` 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.231) Standard Section Test Item Judgment Remark 15.207 Conducted Emission N/A Note(1) 15.203 Antenna Requirement Pass 15.231 Radiated Spurious Emission Pass 15.231 Occupied Bandwidth Pass 15.231 Transmitter Timeout Pass NOTE: (1) ” N/A” denotes test is not applicable in this Test Report. Page 5 of 25 Report No.: NTEK-2013NT0730854F ` 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 6 of 25 Report No.: NTEK-2013NT0730854F ` 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment WIRED BOOSTER Trade Name JETSON Model Name JET-100A Serial Model TT-100A,BS101,TMB100-W Model Difference All the models are the same circuit and RF module, except the model names. Product Description The EUT is a WIRED BOOSTER Product Type Remote Control Operation Frequency: 434.2MHz Modulation Type: ASK Number Of Channel 1CH. Antenna Designation: Integration antenna Antenna Gain(Peak) 5 dBi Output Power: 73.68 dBuV/m Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual. Channel List N/A Adapter N/A Input: DC12V--DC36V Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Table for Filed Antenna Ant . Brand Model Name Antenna Type Connector Gain (dBi) NOTE 1 N/A N/A Integration antenna NA 5 Antenna Page 7 of 25 Report No.: NTEK-2013NT0730854F ` 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX For Conducted Emission Final T…

Text truncated - open the document above for the full version.

Page 25 of 25 Report No.: NTEK-2013NT0730854F ` 6. EUT TEST PHOTO Radiated Measurement Photos