2AAV8QT-14TTransmitter

3 4 5 6 7 1 2 WIRELESS REMOTE CONTROL SET IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS ● Read all instructions carefully before using the wireless remote control set. ● Open the package and check the machine for obvious damage. If there seems to be damage discontinue use and contact the distributor. INSTRUCTIONS: ● Use the wireless remtoe control SET with our fog machines only. ● Connect the power cord of fog machine into a power socket. ● Connect the plug of the receiver into the back socket of the fog machine. ● Turn of the fog machine and allow to warm up to operating level (approximately 5 minutes). ● After the fog machine has warmed up the red light on the receiver will light up, alerting you that the fog machine is ready for operation. ● You need to remove the battery’s insulation tab at the back of the transmitter for the first time you use it. ● Press the "ON" button to spray the fog and press the "OFF" button to stop the fog. ● Be sure to keep you fog machine at least 7 3/4 inches (20cm) away from any flammable material. 1. Power Cord 2. Receiver Indication Light 3. Transmitter Indication Light 4. OFF Button 5. ON Button 6.Battery Insulation Tab Hole 7.Battery Insulation Tab ATTENTION: ● Please obey all notices about peration,safey,and repair. Not obeying these notices will damage the unit and may result in electric shock. ● Don't open the case of the wireless transmitter or receiver if you are not a professional electrician. ● Keep clean and remove water. ● Indoor use only. ● If you need to repair the item, please contact distributor or professional repair works. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Avis d’Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio par un appareil numérique de classe B stipulées dans les Règlement sur l’interférence redio d’industrie Canada.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 SHENZHEN QIAOHUA INDUSTRIES LIMITED 2014-12-11 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, SHENZHEN QIAOHUA INDUSTRIES LIMITED hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product Description: Transmitter Model name: QT-14T,QT-10T,QT-11T,QT-13T,QT-12T,QT-15T,QT-16T FCC ID: 2AAV8QT-14T Sincerely, Client’s signature ： Client’s name / title: Swiss Yang / General Manager Contact information / address: Qiaohua Industrial Zone, Luo Tian Forestry Center,Song Gang Town, Bao An District,Shenzhen, Guangdong, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 SHENZHEN QIAOHUA INDUSTRIES LIMITED 2014-12-11 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AAV8QT-14T We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature ： Client’s name / title: Swiss Yang / General Manager Contact information / address: Qiaohua Industrial Zone, Luo Tian Forestry Center,Song Gang Town, Bao An District,Shenzhen, Guangdong, China

SHENZHEN QIAOHUA INDUSTRIES LIMITED Statement Model number: QT-14T,QT-10T,QT-11T,QT-13T,QT-12T,QT-15T,QT-16T FCC ID: 2AAV8QT-14T We hereb y st ate that these models are identical in interior structure, electrical circuits and compon ents, and just model names and colors are different for the marketing requirement. Your assistance on this matter is highly appreciated. Sincerely, Client’s signature ： Client’s name / title: Swiss Yang / General Manager Contact information / address: Qiaohua Industrial Zone, Luo Tian Forestry Center,Song Gang Town, Bao An District,Shenzhen, Guangdong, China

Antenna

Report No.: ATE20142300 Page 1 of 29 FCC ID: 2AAV8QT-14T ACCURATE TECHNOLOGY CO., LTD APPLICATION CERTIFICATION On Behalf of SHENZHEN QIAOHUA INDUSTRIES LIMITED Transmitter Model No.: QT-14T,QT-10T,QT-11T,QT-13T,QT-12T,QT-15T,QT-16T FCC ID: 2AAV8QT-14T Prepared for : SHENZHEN QIAOHUA INDUSTRIES LIMITED Address : Qiaohua Industrial Zone, Luo Tian Forestry Center,Song Gang Town, Bao An District,Shenzhen, Guangdong, China Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20142300 Date of Test : Nov 20-28,2014 Date of Report : Dec 02,2014 Report No.: ATE20142300 Page 2 of 29 FCC ID: 2AAV8QT-14T ACCURATE TECHNOLOGY CO., LTD TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 3 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Description of Test Facility ......................................................................................................................5 1.3. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3. SUMMARY OF TEST RESULTS................................................................................................... 7 4. THE FIELD STRENGTH OF RADIATION EMISSION ............................................................ 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. The Field Strength of Radiation Emission Measurement Limits..............................................................9 4.3. Configuration of EUT on Measurement ...................................................................................................9 4.4. Operating Condition of EUT ....................................................................................................................9 4.5. Test Procedure ........................................................................................................................................10 4.6. The Field Strength of Radiation Emission Measurement Results ..........................................................11 5. 20DB OCCUPIED BANDWIDTH ................................................................................................ 13 5.1. Block Diagram of Test Setup..................................................................................................................13 5.2. The Bandwidth of Emission Limit According To FCC Part 15 Section 15.231(c) ................................13 5.3. EUT Configuration on Measurement .....................................................................................................14 5.4. Operating Condition of EUT ..................................................................................................................14 5.5. Test Procedure ........................................................................................................................................14 5.6. Measurement Result ...............................................................................................................................14 6. RELEASE TIME MEASUREMENT............................................................................................ 15 6.1. Block Diagram of Test Setup..................................................................................................................15 6.2. Release Time Measurement According To FCC Part 15 Section 15.231(a) ..........................................15 6.3. EUT Configuration on Measurement .....................................................................................................16 6.4. Operating Condition of EUT ..................................................................................................................16 6.5. Test Procedure ........................................................................................................................................16 6.6. Measurement Result ...............................................................................................................................16 7. AVERAGE FACTOR MEASUREMENT .................................................................................... 17 7.1. Block Diagram of Test Setup..................................................................................................................17 7.2. Average factor Measurement according to ANSI C63.4-2009...............................................................17 7.3. EUT Configuration on Measurement .....................................................................................................18 7.4. Operating Condition of EUT ..................................................................................................................18 7.5. Test Procedure ........................................................................................................................................18 7.6. Measurement Result ...............................................................................................................................18 8. ANTENNA REQUIREMENT........................................................................................................ 19 8.1. The Requirement ....................................................................................................................................19 8.2. Antenna Construction ...........................................…

Text truncated - open the document above for the full version.

worst orientation worst orientation