2AB3L-LOOPMST0004Card Case

Getting Started Download the free LoopPay app. Load, store and organize all your cards. To pay using your LoopPay Card, hold your LoopPay Card against the slot where you would normally swipe your credit or debit card and press the buon on the LoopPay Card to pay instantly. It’s that easy. 3 2 1 Congratulations! Welcome to LoopPay LoopPay tutorials are available for the LoopPay Card at: www.looppay.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2014 LoopPay, Inc., All rights reserved. Quick Start Guide Fast. Safe. Everywhere. All your cards in one place Works everywhere 3 / 3 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 LoopPay, Inc Jan. 05, 2015 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ____ LoopPay, Inc__ ___hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (Product description: Card Case model name: LOOPMST0004 FCC ID: 2AB3L-LOOPMST0004) Sincerely, Client’s signature: Client’s name / title: William Graylin / CEO Contact information / address: 8 New England Executive Park, Suite 220, Burlington, MA 01803, Burlington, United States.

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 LoopPay, Inc. Jan. 05, 2015 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AB3L-LOOPMST0004 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title: William Graylin / CEO Contact information / address: 8 New England Executive Park, Suite 220, Burlington, MA 01803, Burlington, United States .

Label information: FCC label location:

Report No. : EESZG10230002-2 Page 1 of 21 TEST REPORT Product : Card Case Trade mark : Loop Card Case Model/Type reference : LOOPMST0004 Serial number : N/A Ratings : 3.7V, 350mAH FCC ID : 2AB3L-LOOPMST0004 Report number : EESZG10230002-2 Date : Jan. 05, 2014 Regulations : See below Test Standards Results 47 CFR FCC Part 15 Subpart C: 2014 PASS Prepared for: LoopPay, Inc. 8 New England Executive Park, Suite 220, Burlington, MA 01803, United States Prepared by: Centre Testing International Building C, Hongwei Industrial Zone, Baoan 70 District, Shenzhen, China TEL: +86-755-3368 3919 FAX: +86-755-3368 3385 Tested by: Reviewed by: Approved by: Date: Jan. 05, 2014 Jimmy Li Lab manager Check No.: 1702098331 Report No. : EESZG10230002-2 Page 2 of 21 TABLE OF CONTENTS 1. GENERAL INFORMATION ......................................................................................................................... 3 2. TEST SUMMARY ........................................................................................................................................ 3 3. PRODUCT INFORMATION ......................................................................................................................... 3 4. MEASUREMENT UNCERTAINTY .............................................................................................................. 4 5. TEST EQUIPMENT LIST ............................................................................................................................. 4 6. SUPPORT EQUIPMENT LIST .................................................................................................................... 4 7. AC CONDUCTED EMISSION TEST ........................................................................................................... 5 7.1. LIMITS ................................................................................................................................................. 5 7.2. BLOCK DIAGRAM OF TEST SETUP ................................................................................................ 5 7.3. PROCEDURE OF CONDUCTED EMISSION TEST .......................................................................... 5 7.4. GRAPHS AND DATA ......................................................................................................................... 6 8. RADIATED EMISSION MEASUREMENT .................................................................................................. 8 8.1. LIMITS ................................................................................................................................................. 8 8.2. BLOCK DIAGRAM OF TEST SETUP ................................................................................................ 8 8.3. TEST PROCEDURE ........................................................................................................................... 9 8.4. TEST RESULT .................................................................................................................................. 10 9. 20DB BANDWIDTH OCCUPIED BANDWIDTH MEASUREMENT .......................................................... 14 9.1. LIMITS ............................................................................................................................................... 14 9.2. BLOCK DIAGRAM OF TEST SETUP .............................................................................................. 14 9.3. TEST PROCEDURE ......................................................................................................................... 14 9.4. TEST RESULT .................................................................................................................................. 14 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ............................................................................................ 15 APPENDIX 2 EXTERNAL PHOTOGRAPHS OF PRODUCT ............................................................................ 17 APPENDIX 3 INTERNAL PHOTOGRAPHS OF PRODUCT ............................................................................. 19 N/A means not applicable. Report No. : EESZG10230002-2 Page 3 of 21 1. GENERAL INFORMATION Applicant: LoopPay, Inc. 8 New England Executive Park, Suite 220, Burlington, MA 01803, United States Manufacturer: BBPOS Limited Suite 1602, 16/F, Tower 2, Nina Tower, No.8 Yeung UK Rd, Tsuen Wan, Hong Kong FCC ID: 2AB3L-LOOPMST0004 Product: Card Case Model/Type reference: LOOPMST0004 Trade Name: Loop Card Case Serial Number: N/A Report Number: EESZG10230002-2 Sample Received Date: Oct. 25, 2014 Sample tested Date: Oct. 25, 2014 to Dec. 01, 2014 The above equipment was tested by Centre Testing International (Shenzhen) Corporation for compliance with the requirements set forth in the FCC Rules and the measurement procedure according to ANSI C63.4:2009. 2. TEST SUMMARY No. Test Item Rule Test Result 1 Conducted Emission FCC 15.207 PASS 2 Radiated Emission FCC 15.209 PASS 3. 20dB Bandwidth Part 2.1049 PASS 4. Antenna Requirement FCC Part 15.203 PASS* *: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi. 3. PRODUCT INFORMATION Items Description Rating 3.7V, 350mAH Type of Modulation ASK Antenna Type Integral antenna Frequency Range 125KHz Gain 0dBi Report No. : EESZG10230002-2 Page 4 of 21 4. MEASUREMENT UNCERTAINTY This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement items Uncertainty Conducted Emission Test 3.2 dB Radiated Emissions / Bandedge Emission 4.5 dB 5. TEST EQUIPMENT LIST Equipment Manufacturer Model Serial No. Due Date 3M Chamber & Accessory Equipment TDK SAC-3 --- 06/01/2016 Spectrum Analyzer Agilent E4443A MY45300910 01/15/2015 Receiver R&S ESCI 100435 07/19/2015 Loop Antenna ETS-LINDGREN6502 00071730 07/22/2015 TRILOG Broadband Antenna schwarzbeck VUL…

Text truncated - open the document above for the full version.