2AB5K-SD5001SD5001

Remote Socket Set User manual A. Function 1. LED on the transmitter (remote control) indicates that a signal is being transmitted. 2. Indicator light on the receiver (socket) indicates that the socket is working. 3. Both transmitter (remote control) and receiver (socket) have 4 channels and 4 codes. 4. The code of the transmitter (remote control) and receiver (socket) can be adjusted. B. The Product: 2 3 4 1 II III IV I 5 3 9 8 7 1 2 4 6 No. Description No. Description No. Description 1 LED light 4 Code adjustment switch 7 Code adjustment dial 2 ON/OFF Channels 5 LED light 8 Channel adjustment dial 3 LED light 6 Battery cover 9 Plug C. Code and Channel Adjustment 1. Code adjustment: Adjust the code of the transmitter and receiver so that they each use the same code (There are 4 corresponding codes). Please refer to the images below: 1 2 3 4 2. Channel adjustment: Adjust the channel of receiver to the corresponding channel of the transmitter, please see the following images: there are 4 corresponding channels 1 2 3 4 PS: Please change the code if you encounter interference with another socket. D. Operation: 1．Adjust the code of both transmitter and receiver so that they are using the same code. 2．Adjust the channel of the receiver to the corresponding channel of the transmitter. 3．Plug your electrical appliance into a receiver socket. Then plug the receiver into the AC socket. 4．Press the corresponding channel on the remote control. Press the “ON” button and the socket will turn on and the LED will illuminate. Press the “OFF” button and the socket will switch off and the LED light will go off. E. Specifications: 1. Transmitter battery: 12V/23A 2. Transmitter radio frequency: 433.92MHz 3. Receiver voltage: 120V / 60Hz / IP20/15A 4. Receiver maximum wattage: 1800W 5. Transmittion range: Typically 30m (clear line of sight) WEEE Directive & Product Disposal At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal Internal / Supplied Batteries This symbol on the battery indicates that the battery is to be collected separately. This battery is designed for separate collection at an appropriate collection point. F .Caution This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2AB5K-SD5001 Page 1 of 1 External Picture

Label Position

FCC ID: 2AB5K-SD5001 Page 1 of 1 Internal Picture

Test report no. 150901622SHA-001 Page 1 of 19 FCC ID: 2AB5K-SD5001 TTRF15.231_V1© 2015Intertek FCC TEST REPORT No. 150901622SHA-001 Applicant : LUMI LEGEND ELECTRICAL CO.LTD. No.18,Lane239,Beihai Road,Jiangbei,Ningbo,China Manufacturer : LUMI LEGEND ELECTRICAL CO.LTD. No.18,Lane239,Beihai Road,Jiangbei,Ningbo,China Product Name : Transmitter Type/Model : SD5001 TEST RESULT : PASS SUMMARY The equipment complies with the requirements according to the following standard(s) or specification: 47CFR Part 15 (2014): Radio Frequency Devices (Subpart C) ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices Date of issue: Dec 17, 2015 Prepared by: Reviewed by: Jesse Xu (Project Engineer) Daniel Zhao(Reviewer) Test report no. 150901622SHA-001 Page 2 of 19 FCC ID: 2AB5K-SD5001 TTRF15.231_V1© 2015Intertek Description of Test Facility Name: Intertek Testing Service Limited Shanghai Address: Building No.86, 1198 Qinzhou Road(North), Shanghai 200233, P.R. China FCC Registration Number: 236597 IC Assigned Code: 2402B-1 Name of contact: Jonny Jing Tel: 86 21 61278271 Fax: 86 21 54262353 Test report no. 150901622SHA-001 Page 3 of 19 FCC ID: 2AB5K-SD5001 TTRF15.231_V1© 2015Intertek Content SUMMARY .............................................................................................................................................1 1 GENERAL INFORMATION .......................................................................................................4 1.1 Description of Client ..................................................................................... 4 1.2 Identification of the EUT .............................................................................. 4 1.3 Technical Specification ................................................................................. 5 2 TEST SPECIFICATIONS ............................................................................................................6 2.1 Standards or specification ............................................................................. 6 2.2 Mode of operation during the test ................................................................. 6 2.3 Test software list ........................................................................................... 6 2.4 Test peripherals list ....................................................................................... 6 2.5 Instrument list ................................................................................................ 7 2.6 Test Summary ................................................................................................ 8 3 FUNDAMENTAL & SPURIOUS EMISSION & RESTRICT BAND RADIATED EMISSION .......................9 3.1 Test limit ........................................................................................................ 9 3.2 Test Configuration ....................................................................................... 10 3.3 Test procedure and test setup ...................................................................... 10 3.4 Test protocol ................................................................................................ 11 4 DEACTIVATING TIME .................................................................................................................... 13 4.1 Test limit ...................................................................................................... 13 4.2 Test Configuration ....................................................................................... 14 4.3 Test procedure and test setup ...................................................................... 14 4.4 Test protocol ................................................................................................ 14 5 EMISSION BANDWIDTH ................................................................................................................. 15 5.1 Test limit ...................................................................................................... 15 5.2 Test Configuration ....................................................................................... 15 5.3 Test procedure and test setup ...................................................................... 15 5.4 Test protocol ................................................................................................ 16 6 CONDUCTED EMISSION ................................................................................................................. 17 6.1 Limit ............................................................................................................ 17 6.2 Test configuration ........................................................................................ 17 6.3 Test procedure and test set up ..................................................................... 18 6.4 Test protocol ................................................................................................ 19 Test report no. 150901622SHA-001 Page 4 of 19 FCC ID: 2AB5K-SD5001 TTRF15.231_V1© 2015Intertek 1 GENERAL INFORMATION 1.1 Description of Client Applicant : LUMI LEGEND ELECTRICAL CO.LTD. No.18,Lane239,Beihai Road,Jiangbei,Ningbo,China. Name of contact : Zhang Xiaohong Tel : 13566578349 Fax : - Email : [email protected] Manufacturer : LUMI LEGEND ELECTRICAL CO.LTD. No.18,Lane239,Beihai Road,Jiangbei,Ningbo,China. 1.2 Identification of the EUT Product Name : Transmitter Type/model : SD5001 FCC ID : 2AB5K-SD5001 Test report no. 150901622SHA-001 Page 5 of 19 FCC ID: 2AB5K-SD5001 TTRF15.231_V1© 2015Intertek 1.3 Technical Specification Operation Frequency Band : 433.92MHz Modulation : ASK Antenna Designation : Integral antenna, non-user removable. Description of EUT : There is one model only. The EUT is a transmitter to control the working condition of the corresponding receiver. Rating : 12V/23A Category of EUT : Class B EUT type : Table top Floor standing …

Text truncated - open the document above for the full version.

FCC ID: 2AB5K-SD5001 Page 1 of 11 Test Data FCC ID: 2AB5K-SD5001 Page 2 of 11 1. Fundamental & Spurious Emission & Restrict band radiated emission Horizontal 30-1000MHz 0 20 40 60 80 100 Level [dBμV/m] 30M50M70M100M 200M 300M500M700M1G Frequency [Hz] x x x x x x x MES JX1019H1_red MES JX1019H1_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: 2AB5K-SD5001 Page 3 of 11 Restrict band 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 399.9M402M 404M 406M408M410M Frequency [Hz] MES ak0529_lH_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: 2AB5K-SD5001 Page 4 of 11 Horizontal 1000-5000 MHz 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 1G2G3G4G5G Frequency [Hz] x x MES JX1019H-1_red MES JX1019H-1_pre LIM FCC 15 F 3 PK Field Strength QP LIM FCC 15 F 3 AV Field Strength QP FCC ID: 2AB5K-SD5001 Page 5 of 11 Vertical 30-1000MHz 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 30M50M70M100M200M300M500M 700M 1G Frequency [Hz] x x x x x x x MES JX1019V1_red MES JX1019V1_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: 2AB5K-SD5001 Page 6 of 11 Restrict band 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 399.9M402M 404M406M 408M 410M Frequency [Hz] LIM FCC 15 F 3 QP Field Strength QP MES ak0529_VL_pre FCC ID: 2AB5K-SD5001 Page 7 of 11 Vertical 1000-5000MHz 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 1G2G3G4G5G Frequency [Hz] MES JX1019V-1_pre LIM FCC 15 F 3 PK Field Strength QP LIM FCC 15 F 3 AV Field Strength QP FCC ID: 2AB5K-SD5001 Page 8 of 11 2. Deactivating time Push the side switch key to the “I” and press the left side of the first key is the worst case. FCC ID: 2AB5K-SD5001 Page 9 of 11 3. Emission bandwidth FCC ID: 2AB5K-SD5001 Page 10 of 11 4. Duty Cycle FCC ID: 2AB5K-SD5001 Page 11 of 11 All the keys were assessed and the test data with maximum duty cycle was listed above. (Push the side switch key to the “I” and press the left side of the first key is the maximum duty cycle) The worst Duty cycle= (10*1.14+ 0.6*15) / 55.82 = 0.412

FCC ID: 2AB5K-SD5001 Page 1 of 2 Test Setup FCC ID: 2AB5K-SD5001 Page 2 of 2 1. Radiated Emission Above 1GHz Below 1GHz