2AB9A-HSBTKB15Bluetooth Keyboard

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. - French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. T he device has been evaluated to meet general RF exposure requirement. T he device can be used in portable exposure condition without restriction.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 THINKMAX TECHNOLOGIES INC. Add: 560 DENISON STREET, UNIT 5, MARKHAM, Ontario, L3R2M8,Canada Tel: 9059489967 Fax: 9059481601 2015-12-15 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA FCC ID: 2AB9A-HSBTKB15 Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, THINKMAX TECHNOLOGIES INC. hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (Product description, model name): Bluetooth Keyboard , UNIV78CS-3N1C Sincerely, Client’s name / title : Josie Lombardi / Purchasing Manager Contact information / address : 560 DENISON STREET, UNIT 5, MARKHAM, Ontario, L3R2M8,Canada Tel: 9059489967 Fax: 9059481601 E-Mail: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template& Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (obsolete) 3.0 4.0 March-26-2015 Corrections to STC form. Added reference to KDB (current) 4.0 5.0 Nov 19 2015 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 5.0 THINKMAX TECHNOLOGIES INC. 2015-12-15 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AB9A-HSBTKB15 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature : Josie Lombardi Client’s name & title : Purchasing Manager Contact information / address: 560 DENISON STREET, UNIT 5, MARKHAM, Ontario, L3R2M8,Canada

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 5 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 5 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 5 Fig.5 Fig.6 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 5 Fig.7 Fig.8 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 5 of 5 Fig.8 Fig.9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size: L3.0cm*W2.0cm Material: Tagboard Glue: adhesive sticker Font color: Black Label color: Black Label And Location Bluetooth Keyboard Model No.: UNIV78CS-3N1C FCC ID: 2AB9A-HSBTKB15 Input: DC 5V/0.5A This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. INTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Fig.6 Bluetooth Antenna

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693M ___________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 FCC RF Exposure Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Portable Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v05r02 FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v05r01Section 4.3.1 Standalone SAR test exclusion considerations:“ Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693M ___________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 Conducted Power Results Bluetooth Mode Channel Frequency (MHz) Peak Conducted Output Power (dBm) GFSK 00 2402 4.37 40 2441 4.46 78 2480 4.47 π/4-DQPSK 00 2402 3.16 40 2441 3.11 78 2480 3.20 8-DPSK 00 2402 2.85 40 2441 2.97 78 2480 2.12 Manufacturing tolerance Bluetooth GFSK (Peak) Channel Channel 00 Channel 40 Channel 78 Target (dBm) 4.0 4.0 4.0 Tolerance ±(dB) 1.0 1.0 1.0 π/4-DQPSK (Peak) Channel Channel 00 Channel 40 Channel 78 Target (dBm) 3.0 3.0 3.0 Tolerance ±(dB) 1.0 1.0 1.0 8-DQPSK (Peak) Channel Channel 00 Channel 40 Channel 78 Target (dBm) 3.0 3.0 3.0 Tolerance ±(dB) 1.0 1.0 1.0 Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW GFSK 2.402 5 5.0 3.1623 0.9802<3.0 Yes 2.441 5 5.0 3.1623 0.9881<3.0 Yes 2.480 5 5.0 3.1623 0.9960<3.0 Yes π/4-DQPSK 2.402 5 4.0 2.5119 0.7786<3.0 Yes 2.441 5 4.0 2.5119 0.7849<3.0 Yes 2.480 5 4.0 2.5119 0.7911<3.0 Yes 8-DPSK 2.402 5 4.0 2.5119 0.7786<3.0 Yes 2.441 5 4.0 2.5119 0.7849<3.0 Yes 2.480 5 4.0 2.5119 0.7911<3.0 Yes Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v05r02. .......................END OF REPORT.........................

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 45 FCC TEST REPORT FOR THINKMAX TECHNOLOGIES INC. Bluetooth Keyboard Model No.: UNIV78CS-3N1C Prepared for : THINKMAX TECHNOLOGIES INC. Address : 560 DENISON STREET, UNIT 5, MARKHAM, Ontario, L3R2M8, Canada Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : December 08, 2015 Number of tested samples : 1 Serial number : Prototype Date of Test : December 08, 2015 – December 14, 2015 Date of Report : December 14, 2015 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 45 FCC TEST REPORT FCC CFR 47 PART 15 C(15.247): 2015 Report Reference No. ............... : LCS1512080693E Date of Issue ................................. : December 14, 2015 Testing Laboratory Name .......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ......................................... : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Testing Location/ Procedure ......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : THINKMAX TECHNOLOGIES INC. Address ......................................... : 560 DENISON STREET, UNIT 5, MARKHAM, Ontario, L3R2M8, Canada Test Specification Standard ........................................ : FCC CFR 47 PART 15 C(15.247): 2015 Test Report Form No. ................... : LCSEMC-1.0 TRF Originator ............................. : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ................ : Bluetooth Keyboard Trade Mark ................................... : HIPSTREET Model/ Type reference .................. : UNIV78CS-3N1C Ratings .......................................... : DC 3.7V by battery (150mAh) Recharge Voltage: DC 5V/0.5A Result ......................................... : Positive Compiled by: Supervised by: Approved by: Dick Su / File administrators Glin Lu/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 45 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1512080693E December 14, 2015 Date of issue Type / Model........................... : UNIV78CS-3N1C EUT......................................... : Bluetooth Keyboard Applicant............................... : THINKMAX TECHNOLOGIES INC. Address.................................. : 560 DENISON STREET, UNIT 5, MARKHAM,Ontario, L3R2M8, Canada Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Shenzhen Phaeton Nice Electronic High-tech Co. Limited Address................................... : Block B2, He Xia Ling Industry Park, Ping Xin Road, Pinghu Town, Longgang District, Shenzhen, China Telephone............................... : / Fax.......................................... : / Factory................................... : Shenzhen Phaeton Nice Electronic High-tech Co. Limited Address................................... : Block B2, He Xia Ling Industry Park, Ping Xin Road, Pinghu Town, Longgang District, Shenzhen, China Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 45 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .............................................................................................. 5 1.1 Description of Device (EUT) ...................................................................................................... 5 1.2 Support equipment List ................................................................................................................ 5 1.3 External I/O Cable ........................................................................................................................ 5 1.4 Description of Test Facility .......................................................................................................... 6 1.5 Statement of The Measurement Uncertainty ................................................................................ 6 1.6 Measurement Uncertainty..............................................................................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement (X Position) Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AB9A-HSBTKB15 Report No.: LCS1512080693E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 1.2. Photo of Line Conducted Emissions