2ABC8-5898Wireless DUAL TEC Motion Sensor

5898 - Installation Instructions / Instructions de montage / Instrucciones de Instalación PRELIMINARY DRAFT 1/14/10 5898 - Installation Instructions / Instructions de montage / Instrucciones de Instalación PRELIMINARY DRAFT 1/14/10 - Page 2 - ENGLISH ENROLL THE SENSOR Enroll the sensor in the control panel prior to its usage in the system. Refer to the control’s instructions for programming details. Program the sensor as an “RF” type (supervised RF) device. Sensor Loops: Pulse Count 2 Loop 1 Medium Sensitivity Up to 50 lb. (23kg) Animal Immunity (with Animal Immune Lens + DIP Switch 1 OFF) Low Sensitivity Up to 100 lb. (45kg) Animal Immunity (with Animal Immune Lens + DIP Switch 1 ON) Loop 2 Pulse Count 1 / High Sensitivity No Animal Immunity Loop 3 *[± 3.6° F (2° C)] Low Temperature Alarm (with DIP Switch 2 OFF) Fault = < 45° F (7° C)* for > 20 - 60 minutes Restore = > 48° F (9° C)* for > 20 - 60 minutes High Temperature Alarm (with DIP Switch 2 ON) Fault = > 95° F (35° C)* for > 20 - 60 minutes Restore = < 92° F (33° C)* for > 20 - 60 minutes Note: Program each desired loop as a separate zone with the appropriate zone type response. To enroll: connect the battery and wait for power up to end (see LED Indications table). When prompted for the serial number, activate the sensor (wave a hand in front of the lens) to enroll default loop 1 (low sensitivity). For loop 2 and/or loop 3, program an appropriate zone and enroll using the tamper switch. Change the loop number at the keypad. NOTE: In normal mode, the sensor transmits all loop signals as they occur, but the control processes only the loops programmed. MOUNT THE SENSOR (See page 1)  Before mounting the transmitter permanently, conduct Go/No Go tests (see control panel manual) to verify adequate signal strength and reorient or relocate the sensor if necessary. For Animal (Pet) Immunity:  Install Animal Immune lens (5-532-489-01) and look-down mask (see A and B).  Set DIP Switch 1 (see D).  Install the sensor where animals cannot come within 6 ft (1.8 m) of the sensor by climbing on furniture or other objects.  Aim the sensor away from stairways, furniture or other objects that can be climbed on by animals.  Do not use optional swivel mount brackets. WALK TEST MODES There are three 10-minute walk test modes (described below). To extend a walk test, see Flashlight feature section. The Enroll and LED Walk Test modes let you test loop 1 and loop 2 detection patterns by lighting the LED when activated as shown in the table below: LED Indications: To select the loop / sensitivity level, use the Flashlight feature. ENROLL Walk Test Mode (to enroll or walk test the sensor): This mode is active for 10 minutes and begins either after power up or the sensor cover is opened and closed. When faulted in this mode, the sensor transmits alarm signals to the panel for the selected loop only, and the LED flashes the relative loop indication. LED Walk Test Mode (to walk test the detection pattern): This mode is active for 10 minutes and is activated using the flashlight feature after Enroll Walk Test mode expires. In this mode, the sensor transmits both loop alarms as they occur, mimicking normal operation. The LED, however, only indicates the selected loop when it is alarmed, allowing a walk test of each loop/sensitivity setting. MICROWAVE Walk Test mode (to test and adjust the microwave range): 1. Set the Microwave Walk Test DIP switch (4) to ON, or toggle it ON and OFF after the sensor powers up (see D). 2. Set the Range Adjustment potentiometer to 25% and replace the cover. 3. Walk through the detection area and observe the LED. (See LED Indicator table.) 4. If necessary, adjust the potentiometer to obtain the desired detection range. Note: In ENROLL and LED Walk Test modes all transmissions will be sent as they occur. During normal operation, only one transmission sequence will occur within a 3-minute period to conserve battery life. (No alarms are transmitted during Microwave Walk Test mode.) Flashlight feature: (Not available in Microwave Walk Test mode.) 1. Use a flashlight with a bright, narrow light beam and stand within 4 feet (1.2 m) of the sensor. 2. Focus the light beam on the sensor lens for 1 second on / 1 second off (typically 3 - 5 times), until the Red LED flickers rapidly. Notes: Every time you use the flashlight feature, the loop/sensitivity changes and the walk test timer restarts for 10 minutes. The flashlight feature is initially only available for 24 hours after power up. Subsequent tamper activations will enable this feature for 2 hours to allow for sensor detection verification after initial installation. TROUBLESHOOTING Problem: The sensor LED indicates a trouble condition (see LED indicator table). A self test failure has occurred, which causes the sensor to stop transmitting RF supervision messages. If the condition exceeds the panel’s RF supervision time, the panel will generate an RF supervision trouble. (Self Tests: Microwave Supervision, End-to-End PIR self test, Temperature Compensation.) If a microwave supervision failure occurs, the sensor will operate as a PIR sensor and signal trouble on the red LED. On the first PIR alarm following the microwave supervision failure, the unit will stop sending RF messages until the trouble is cleared or the sensor is replaced. Solution: Remove and reinstall the batteries. If the trouble does not clear, replace the sensor. Problem: The system displays a “low battery” message. Solution: Replace the batteries within 7 days. RF TRANSMITTING 345MHz RF transmitting only if 1. Tamper and Intrusion trigger alarm 2. Low battery detection 3. Self Tests failure, then Fault warning FRANÇAIS ENRÔLEMENT DU DÉTECTEUR Avant d’utiliser le détecteur dans le système, vous devez l’enrôler dans le panneau de commande. Pour les détails concernant la programmation, reportez-vous aux instructions du panneau de commande. Programmez le détecteur avec le type de dispositif « RF » (RF supervisé). Boucle…

Text truncated - open the document above for the full version.

Report No.: 150623E05 Page 1 CONSTRUCTION PHOTOS OF EUT

PROPOSED FCC ID LABEL AND LOCATION FCC ID: 2ABC8-5898 EUT: FCC Label Location Inside ENREV DESCRIPTION CHK DATE APPVD DATE EC-47184A Production Release Ting 07/15 Terry 07/15 Notes: Unless otherwise specified 1. MATERIAL: Alternate: P/N 5-045-034-00 (Specification for label material: UL Recog. PGDQ2 OR PGGU2). 2. PRINT COLOR: Black Ink 3. ARTMASTER: 800-21069A.EPS 4. SOURCE FILE FORMAT: CorelDraw V13.0. 5. Bag and tag with P/N, and revision, vendor name or logo. Material: White Polyester, Honeywell P/N 5-045-024-00. Label,Hook-Up/Compliance,5898VE 800-21069 Ting.G Terry.Z 07/15 07/15 PN 5-017-098-00 Rev. C Size: A Drawing No.: Rev.: Title: Approvals: Unless otherwise specified: Tolerances are: .X ? 0.3 [.01] .XX ? 0.13 [.005] Angles +/- 0.5? Dimensions are in millimeters [inches]. DWN. ECO No.: APPRV. CHECK A All information contained hereon is the property of Honeywell and is considered proprietary and subject to return upon demand. Acceptance and retention hereof signifies agreement by the recipient that the information will not be disclosed to others nor used contrary to the interests of Honeywell without prior written permission. Scale: 1:1 Do Not Scale Drawing Page: 1 of 1 Date: 8.95 [0.352] 8.95 [0.352] 49.80 [1.961] 27.25 [1.073] 19.06 [0.751] 6.40 [0.252] Ø7,00 [0.276] + 25%50% 100%75% MEDIUM LOW TEMP LO 60Hz NORMAL TEMP HI 50Hz MW OFFON Model 5898 N219 FCC ID: 2ABC8-5898 IC: 11596A-5898 IC_Model: 5898 Protected under USA patents: 5,499,012 & 6,121,876 and related international patents. EC-47184

Report No.: 150623E05 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 150623E05 Page 2 Report No.: 150623E05 Page 3 Report No.: 150623E05 Page 4 Report No.: 150623E05 Page 5 Report No.: 150623E05 Page 6 Report No.: 150623E05 Page 7

Report No.: SA150623E05 Page No. 1 / 6 Report Format Version: 6.1.1 Reference No.: RF Exposure Report Report No.: SA150623E05 FCC ID: 2ABC8-5898 Test Model: 5898 Received Date: June 23, 2015 Test Date: Aug. 19, 2015 Issued Date: Oct. 02, 2015 Applicant: Honeywell Security Sensor CoE Address: 38F, Block A of Galaxy Century Building, No.3069 Caitian Road, Fu Tian District, Shenzhen, China Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA150623E05 Page No. 2 / 6 Report Format Version: 6.1.1 Reference No.: Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Power .............................................................................................. 6 Report No.: SA150623E05 Page No. 3 / 6 Report Format Version: 6.1.1 Reference No.: Release Control Record Issue No. Description Date Issued SA150623E05 Original release. Oct. 02, 2015 Report No.: SA150623E05 Page No. 5 / 6 Report Format Version: 6.1.1 Reference No.: 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA150623E05 Page No. 6 / 6 Report Format Version: 6.1.1 Reference No.: 3 Calculation Result of Maximum Power Frequency Band Max Field Strength Of Fundamental (dBuV/m) Max Pout EIRP (dBm) Max Pout EIRP (mW) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 345 MHz 88.6 -6.63 0.2173 20 0.00004 0.23 (See Note 2) 10.527 GHz 108.9 13.67 23.2809 20 0.00463 1 Note: 1. Pout EIRP (dBm) = Field Strength of Fundamental (dBuV/m) - 95.23 (dB) 2. Limit of Electric field=F/1500 Conclusion: Both of the 345MHz and 10.527GHz can transmit simultaneously, the formula of calculated the MPE is: CPD 1 / LPD 1 + CPD 2 / LPD 2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density Therefore, the worst-case situation is 0.00004 / 0.23 + 0.00463 / 1 = 0.005, which is less than “1”. This confirmed that the device comply with FCC 1.1310 MPE limit. --- END ---

Report No.: RF150623E05-1 Page No. 1 / 24 Report Format Version: 6.1.1 Reference No.: FCC Test Report Report No.: RF150623E05-1 FCC ID: 2ABC8-5898 Test Model: 5898 Received Date: June 23, 2015 Test Date: Aug. 04 to 19, 2015 Issued Date: Oct. 02, 2015 Applicant: Honeywell Security Sensor CoE Address: 38F, Block A of Galaxy Century Building, No.3069 Caitian Road, Fu Tian District, Shenzhen, China Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150623E05-1 Page No. 2 / 24 Report Format Version: 6.1.1 Reference No.: Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 8 3.3 Description of Support Units ............................................................................................................. 10 3.3.1 Configuration of System under Test .................................................................................................. 10 3.4 General Description of Applied Standards ......................................................................................... 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 15 4.1.5 Test Setup .......................................................................................................................................... 16 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Band Edge Measurement ................................................................................................................. 21 4.2.1 Limits of Band Edge Measurement ................................................................................................... 21 4.2.2 Test Setup .......................................................................................................................................... 21 4.2.3 Test Instruments…

Text truncated - open the document above for the full version.

Report No.: RF150623E05 Page No. 1 / 25 Report Format Version: 6.1.1 Reference No.: FCC Test Report Report No.: RF150623E05 FCC ID: 2ABC8-5898 Test Model: 5898 Received Date: June 23, 2015 Test Date: Aug. 14 to 19, 2015 Issued Date: Oct. 02, 2015 Applicant: Honeywell Security Sensor CoE Address: 38F, Block A of Galaxy Century Building, No.3069 Caitian Road, Fu Tian District, Shenzhen, China Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150623E05 Page No. 2 / 25 Report Format Version: 6.1.1 Reference No.: Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 8 3.3 Description of Support Units ............................................................................................................. 10 3.3.1 Configuration of System under Test .................................................................................................. 10 3.4 General Description of Applied Standards ......................................................................................... 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission Measurement ..................................................................................................... 12 4.1.1 Limits of Radiated Emission Measurement ....................................................................................... 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions ................................................................................................................. 15 4.1.7 Test Results ....................................................................................................................................... 16 4.2 20dB Bandwidth Measurement ......................................................................................................... 20 4.2.1 Limits of 20dB Bandwidth Measurement ........................................................................................... 20 4.2.2 Test Setup .......................................................................................................................................... 20 4.2.3 Test …

Text truncated - open the document above for the full version.

Report No.: 150623E05 1 of 2 Reference No.: PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST (Below 1GHz) Report No.: 150623E05 2 of 2 Reference No.: RADIATED EMISSION TEST (Above 1GHz)