2ABCB-RPI21Credit Card Sized Computer

RaspbeRRy pi RegulatoRy ComplianCe and safety infoRmation Product Name: Raspberry Pi Model B IMPORTANT: PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE For full set up and installation instructions please visit http://www.raspberrypi.org/qsg WaRnings n This product shall only be connected to an external power supply rated at 5V dc, and a minimum current of 700-1200mA. Any external power supply used with the Raspberry-Pi shall comply with relevant regulations and standards applicable in the country of intended use. n This product should not be overclocked as this may make certain components very hot. n This product should be operated in a well ventilated environment and the case should not be covered. n This product should be placed on a stable, flat, non-conductive surface in use and should not be contacted by conductive items. n The connection of unapproved devices to the GPIO connector may affect compliance or result in damage to the unit and invalidate the warranty. n All peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors, and mice used in conjunction with the Raspberry Pi. n Where peripherals are connected that do not include the cable or connector, the cable or connector used must offer adequate insulation and operation in order that the requirements of the relevant performance and safety requirements are met. instRuCtions foR safe use To avoid malfunction or damage to your Raspberry Pi please observe the following: n Do not expose it to water, moisture or place on a conductive surface whilst in operation. n Do not expose it to heat from any source; the Raspberry Pi is designed for reliable operation at normal ambient room temperatures. n Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors. n Avoid handling the printed circuit board while it is powered. Only handle by the edges to minimise the risk of electrostatic discharge damage. n The Raspberry Pi is not designed to be powered from a USB port on other connected equipment, if this is attempted it may malfunction. RP Safety Leaflet A6 v1.5.indd 103/02/2014 14:25 ComplianCe infoRmation The Raspberry Pi complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the Raspberry Pi should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions. ElEctromagnEtic compatibility anD opEration n This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. n This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to the European Standard EN 55022. n This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. n NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ❍ Reorient or relocate the receiving antenna ❍ Increase the separation between the equipment and receiver ❍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ❍ Consult the dealer or an experienced radio/TV technician for help n This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. n WARNING: Please do not alter or modify the design of this product, doing so may void your ability to use the product freely, this includes altering the frequency at which the product operates. This product is licensed under the MPEG-4 Visual Patent Portfolio License for the personal and non-commercial use of a consumer for (i) encoding video in compliance with the MPEG-4 Visual Standard (“MPEG-4 Video”) and/ or (ii) decoding MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed by MPEG LA to provide MPEG-4 Video. No license is granted or shall be implied for any other use. Additional information including that relating to promotional, internal and commercial uses and licensing may be obtained from MPEG LA, LLC. See http://www.mpegla.com. This product is licensed under the AVC Patent Portfolio License for the personal use of a consumer or other uses in which it does not receive remuneration to (i) encode video in compliance with the AVC Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a consumer engaged in a personal activity and/or was obtained from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com Newark element14, 4801 North Ravenswood Avenue, Chicago IL 60640 USA Premier Farnell UK, 150 Armley …

Text truncated - open the document above for the full version.

1 1Insert SD card See page 3 for how to prepare the SD card 3Connect input Plug in a USB keyboard and mouse 2aConnect display Plug in your digital TV or monitor 4Connect network Connect to your wired network [optional] 5Power up Plug in the micro USB power supply 2bConnect display If not using HDMI, plug in your analogue TV or display Quick start 1 To set up your Raspberry Pi you will need: ItemMinimum recommended specification & notes 1SD card• Minimum size 4Gb; class 4 (the class indicates how fast the card is). • We recommend using branded SD cards as they are more reliable. 2aHDMI to HDMI / DVI lead• HDMI to HDMI lead (for HD TVs and monitors with HDMI input). OR HDMI to DVI lead (for monitors with DVI input). • Leads and adapters are available for few pounds -- there is no need to buy expensive ones! 2bRCA video lead• A standard RCA composite video lead to connect to your analogue display if you are not using the HDMI output. 3Keyboard and mouse• Any standard USB keyboard and mouse should work. • Keyboards or mice that take a lot of power from the USB ports, however, may need a powered USB hub. This may include some wireless devices. 4Ethernet (network) cable [optional] • Networking is optional, although it makes updating and getting new software for your Raspberry Pi much easier. 5Power adapter• A good quality, micro USB power supply that can provide at least 700mA at 5V is essential. • Many mobile phone chargers are suitable—check the label on the plug. • If your supply provides less than 5V then your Raspberry Pi may not work at all, or it may behave erratically. Be wary of very cheap chargers: some are not what they claim to be. • It does not matter if your supply is rated at more than 700mA. 6Audio lead [optional]• If you are using HDMI to HDMI then you will get digital audio via this. • If you are using the analogue RCA connection or a HDMI to DVI cable, stereo audio is available from the 3.5mm jack next to the RCA connector. HDMI connector RCA composite video connector HDMI to DVI lead Know your leads: 2 3 WARnIngS n This product shall only be connected to an external power supply rated at 5V dc, and a minimum current of 500-700mA for model A and 700-1200mA for model B. Any external power supply used with the Raspberry-Pi shall comply with relevant regula - tions and standards applicable in the country of intended use. n This product should not be overclocked as this may make certain components very hot. n This product should be operated in a well ventilated environment and the case should not be covered. n This product should be placed on a stable, flat, non-conductive surface in use and should not be contacted by conductive items. n The connection of unapproved devices to the GPIO connector may affect compliance or result in damage to the unit and invali- date the warranty. n All peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accord- ingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors, and mice used in conjunction with the Raspberry Pi. n Where peripherals are connected that do not include the cable or connector, the cable or connector used must offer adequate insulation and operation in order that the requirements of the relevant performance and safety requirements are met. InSTRuCTIOnS fOR SAfe uSe n Do not expose it to water, moisture or place on a conductive surface whilst in operation. n Do not expose it to heat from any source; the Raspberry Pi is designed for reliable operation at normal ambient room tempera- tures. n Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors. n Avoid handling the printed circuit board while it is powered. Only handle by the edges to minimise the risk of electrostatic dis- charge damage. n The Raspberry Pi is not designed to be powered from a USB port on other connected equipment, if this is attempted it may malfunction. PRePARIng yOuR SD CARD fOR The RASPbeRRy PI In order to use your Raspberry Pi, you will need to install an Operating System (OS) onto an SD card. An Operating System is the set of basic programs and utilities that allow your computer to run; examples include Windows on a PC or OSX on a Mac. These instructions will guide you through installing a recovery program on your SD card that will allow you to easily install different OS’s and to recover your card if you break it. 1. Insert an SD card that is 4GB or greater in size into your computer 2. Format the SD card so that the Pi can read it a. Windows i. Download the SD Association’s Formatting Tool from https://www.sdcard.org/downloads/formatter_4/eula_ windows/ ii. Install and run the Formatting Tool on your machine iii. Set “FORMAT SIZE ADJUSTMENT” option to “ON” in the “Options” menu iv. Check that the SD card you inserted matches the one selected by the Tool v. Click the “Format” button b. Mac i. Download the SD Association’s Formatting Tool from https://www.sdcard.org/downloads/formatter_4/eula_ mac/ ii. Install and run the Formatting Tool on your machine iii. Select “Overwrite Format” iv. Check that the SD card you inserted matches the one selected by the Tool v. Click the “Format” button c. Linux i. We recommend using gparted (or the command line version parted) 3. Format the entire disk as FAT 3. Download the New Out Of Box Software (NOOBS) from: downloads.raspberrypi.org/noobs 4 4. Unzip the downloaded file a. Windows i. Right click on the file and choose “Extract all” b. Mac i. Double tap on the file c. Linux i. Run unzip [downloaded filename] 5. Copy the extracted files onto the SD card that you just formatted 6. Insert the SD card into your Pi and connect the power supply Your Pi will now boot into NOOBS and should display a list of operating systems that you can choose to install. If your display remains blank, you should select the correct output mode for your…

Text truncated - open the document above for the full version.

|---------- ( Cambridge Ltd. ) ----------| Testing EMCEMC Consultancy EMC Training or : 01223 241140 (accounts) 23, Headington Drive, Cambridge. CB1 9HE Tel : 01954 251974 (test site) Fax : 01954 251907 email: [email protected] web : www.dbtechnology.co.uk REPORT ON ELECTROMAGNETIC COMPATIBILITY TESTS Performed at: TWENTY PENCE TEST SITE Twenty Pence Road, Cottenham, Cambridge U.K. CB24 8PS on Raspberry Pi (Trading) Ltd Raspberry Pi dated 9th December 2013 Document History Initial release09/12/131 Approved by Revised by Description of modifications Affected page(s) DateIssue Based on report template: v090319 1 of 37 Page: Test Report T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Equipment Under Test (EUT):Raspberry Pi Test Commissioned by:Raspberry Pi (Trading) Ltd Mount Pleasant House Mount Pleasant Cambridge Cambridgeshire CB3 0RN Representative:Gordon Hollingworth Test Started:7th December 2013 Test Completed:8th December 2013 Test Engineer:Dave Smith Date of Report:9th December 2013 Written by:Dave SmithChecked by:Derek Barlow Signature:Signature: Date:9th December 2013Date:9th December 2013 dB Technology can only report on the specific unit(s) tested at its site. The responsibility for extrapolating this data to a product line lies solely with the manufacturer. Test Standards Applied CFR 47Code of Federal Regulations: Pt 15 Subpart B- Radio Frequency Devices - Class BUnintentional Radiators 2 of 37 Page: Test Report T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Emissions Test Results Summary CFR 47PASS TestPortMethodLimitPASS/FAILNotes Conductedac powerANSI C63.4:2003FCC_BPASS Emissions conducted Radiated ANSI C63.4:2003FCC_BPASS Emissions radiated specs_fccv100412 3 of 37 Page: Test Report T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Contents 37 PLOT 12 Radiated Emissions - 3GHz to 5GHz - Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . 36 PLOT 11 Radiated Emissions - 1GHz to 3GHz - Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 PLOT 10 Radiated Emissions - 250MHz to 1GHz - Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 PLOT 9 Radiated Emissions - 25MHz to 275MHz - Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 PLOT 8 Radiated Emissions - 3GHz to 5GHz - HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 PLOT 7 Radiated Emissions - 1GHz to 3GHz - HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 PLOT 6 Radiated Emissions - 250MHz to 1GHz - HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 PLOT 5 Radiated Emissions - 25MHz to 275MHz - HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 PLOT 4 Conducted Emissions - Composite - Neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 PLOT 3 Conducted Emissions - Composite - Live . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 PLOT 2 Conducted Emissions - HDMI - Neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 PLOT 1 Conducted Emissions - HDMI - Live . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.10 Radiated Emissions Results - Composite Video mode; >1GHz - Horizontal . . . . . . . . . . . . . . . . . . 24 4.9 Radiated Emissions Results - Composite Video mode; >1GHz - Vertical . . . . . . . . . . . . . . . . . . . . . 23 4.8 Radiated Emissions Results - HDMI mode; >1GHz - Horizontal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.7 Radiated Emissions Results - HDMI mode; >1GHz - Vertical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.6 Radiated Emissions Results - Composite Video mode; <1GHz - Horizontal . . . . . . . . . . . . . . . . . . . 20 4.5 Radiated Emissions Results - Composite Video mode; <1GHz - Vertical . . . . . . . . . . . . . . . . . . . . . 19 4.4 Radiated Emissions Results - HDMI mode; <1GHz - Horizontal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.3 Radiated Emissions Results - HDMI mode; <1GHz - Vertical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.2 Conducted Emissions (Power) - Composite Video Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.1 Conducted Emissions (Power) - HDMI Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4 Test Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 15 3.2 Radiated Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 15 3.1 Conducted Emissions - ac power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . 15 3 Test Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . 14 2 Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . 13 Photograph 10 Radiated Emissions - Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Photograph 9 Radiated Emissions - HDMI . . . . . . . .…

Text truncated - open the document above for the full version.

|---------- ( Cambridge Ltd. ) ----------| Testing EMCEMC Consultancy EMC Training or : 01223 241140 (accounts) 23, Headington Drive, Cambridge. CB1 9HE Tel : 01954 251974 (test site) Fax : 01954 251907 email: [email protected] web : www.dbtechnology.co.uk PHOTOS FOR FCC EMC TESTS Performed at: TWENTY PENCE TEST SITE Twenty Pence Road, Cottenham, Cambridge U.K. CB24 8PS on Raspberry Pi (Trading) Ltd Raspberry Pi dated 9th December 2013 Document History Initial release09/12/131 Approved by Revised by Description of modifications Affected page(s) DateIssue Based on report template: v090319 1 of 6 Page: Photos File T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Photograph 1 Conducted Emissions - Front, HDMI Photograph 2 Conducted Emissions - Back, HDMI 2 of 6 Page: Photos File T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Photograph 3 Conducted Emissions - Front , Composite Video Photograph 4 Conducted Emissions - Back, Composite Video 3 of 6 Page: Photos File T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Photograph 5 Radiated Emissions - HDMI Photograph 6 Radiated Emissions - HDMI 4 of 6 Page: Photos File T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Photograph 7 Radiated Emissions - Composite Video Photograph 8 Radiated Emissions - Composite Video 5 of 6 Page: Photos File T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd. Photograph 9 Radiated Emissions - HDMI Photograph 10 Radiated Emissions - Composite Video 6 of 6 Page: Photos File T5145 Test No: FCC ID: 2ABCB-RPI21 R3296 1 Report No: Issue No: This report shall not be reproduced except in full, without the written approval of: dB Technology (Cambridge) Ltd.