2ABHA7199-63Bran Bluetooth Speaker Powerbank

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

March 31, 2015 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Shenzhen Alpha Product Testing Co., Ltd. Address: Building B, East Area of Nanchang Second Industrial Zone, Gushu 2nd Road, Bao'anDistrict, Shenzhen 518126,P.R.China Person: Mark Zhu (Name and address，person). to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Ningbo Cstar Imp&Exp Co.,Ltd. Address: Building E, No.90, Lane 655, Qiming Road,Yinzhou District, Ningbo, China ( applicant name and address). Signature: Name Vincent Chen Position Manager Company Name Ningbo Cstar Imp&Exp Co.,Ltd Address Building E, No.90, Lane 655, Qiming Road,Yinzhou District, Ningbo, China Tel 13691689920 Fax 0574-82822723 Email [email protected]

March 31, 2015 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ABHA7199-63 _ Product Name: Bran Bluetooth Speaker Powerbank Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics Long-term confidential  Block diagram Long-term confidential  Operation description Long-term confidential These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this March 31, 2015 Agency agreement expiration date: Usually Give 8 - 12 Months By: Vincent Chen Signature Printed Title: Manager On behalf of : (Company Name) Ningbo Cstar Imp&Exp Co.,Ltd Telephone: 13691689920

20mm 7mm FCC ID: 2ABHA7199-63

Label location

Antenna

RF Exposure evaluation According to KDB 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√ f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Worse case is as below: [2402 MHz 2.67dBm（1.85mW） output power] (1.85mW /5mm) ·[√2.402(GHz)]= 0.574<3.0 for 1-g SAR Then SAR evaluation is not required

Shenzhen Alpha Product Testing Co., Ltd. TEST REPORT FCC ID: 2ABHA7199-63 Applicant : Ningbo Cstar Imp&Exp Co., Ltd Address : Building E, No.90, Lane 655, Qiming Road,Yinzhou District, Ningbo, China Equipment Under Test (EUT): Name : Bran Bluetooth Speaker Powerbank Model : 7199-63 Trade Name N/A Standards : FCC PART 15, SUBPART C : 2014 (Section 15.247) Report No :A1850166 01 Date of Test :March 18- 25, 2015 Date of Issue :March 28, 2015 Ts e t R e s u l t : PASS In the configuration tested, the EUT complied with the standards specified above Authorized Signature (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Alpha Product Testing Co., Ltd. Or test done by Shenzhen Alpha Product Testing Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Alpha Product Testing Co., Ltd Approvals in writing. Page 2 of 65 A1850166 01 Contents 1.General Information ............................................................................................................... 4 1.1.Description of Device (EUT) ...............................................................................4 1.2.Accessories of device (EUT) ...............................................................................5 1.3.Test Lab information ............................................................................................5 2.Summary of test ...................................................................................................................... 6 2.1.Summary of test result .........................................................................................6 2.2.Assistant equipment used for test .........................................................................6 2.3.Block Diagram .....................................................................................................7 2.4.Test mode .............................................................................................................7 2.5.Test Conditions .....................................................................................................8 2.6.Measurement Uncertainty (95% confidence levels, k=2) ....................................8 2.7.Test Equipment .....................................................................................................9 3.Maximum Peak Output power ............................................................................................ 10 3.1.Limit ...................................................................................................................10 3.2.Test Procedure ....................................................................................................10 3.3.Test Setup ...........................................................................................................10 3.4.Test Result ..........................................................................................................10 4.Bandwidth ............................................................................................................................. 11 4.1.Limit ................................................................................................................... 11 4.2.Test Procedure .................................................................................................... 11 4.3.Test Result .......................................................................................................... 11 5.Carrier Frequency Separation ............................................................................................. 17 5.1.Limit ...................................................................................................................17 5.2.Test Procedure ....................................................................................................17 5.3.Test Result ..........................................................................................................17 6.Number Of Hopping Channel ............................................................................................. 20 6.1.Limit ...................................................................................................................20 6.2.Test Procedure ....................................................................................................20 6.3.Test Result ..........................................................................................................20 7.Dwell Time ............................................................................................................................. 23 7.1.Test limit ............................................................................................................23 7.2.Test Procedure ....................................................................................................23 7.3.Test Results ........................................................................................................23 8.Radiated emissions ................................................................................................................ 29 8.1.Limit ...................................................................................................................29 8.2.Block Diagram of Test setup ..............................................................................30 8.3.Test Procedure ....................................................................................................30 8.4.Test Result ..........................................................................…

Text truncated - open the document above for the full version.

Radiated emission