2ABREIVF-BT01Distance monitoring bracelet

Distance monitoring bracelet 1 User manual Distance monitoring bracelet Smart Bracelet/Bluetooth Wristband/Distance Reminder/Protector Distance monitoring bracelet 2 Model：IVF-BT01 Product overview： A novel coronavirus monitor is designed for IVF-BT01 distance monitoring bracelet. It can monitor the distance of each other by Bluetooth technology to ensure that people keep a certain distance. Parameter： 1、Dimension：38(L)*30(W)*13mm(H) without wristband，260(L)*36mm(W)*16.6mm(H) with strap 2、Weight：41g 3、Color Options：Black/White/Sky-Blue/Orange 4、Material：PC + Silicon 5、Major Function：Distance Monitor of 190c with Auto-detection & Closing Reminder between any two devices 6、Detect Accuracy： 190cm ± 30cm 7、Detect Time：Two seconds 8、Working Days：Continue 40days/per battery (Motor vibration frequency is not considered) 9、BT：Bluetooth 4.0 and above 10、Vibrator：Closing Alarm Support 11、LED：Closing Alarm Support 12、Battery Type：CR2477 Coin Battery (Please open the battery diaphragm before use) 13、Capacity：950mAh 14、Charging Method：Replaceable Battery Design EU DECLARATION OF CONFORMITY Hereby, Xiamen Innov Information Technology Co.,LTD declares that the radio equipment type IVF-BT01 is in compliance with Directive 2014/53/EU. Distance monitoring bracelet 3 FCC Caution § 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. § 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Xiamen Innov Information Technology Co.,LTD Address: INNOV Industrial Park, Tong Long two Road 943, Xiang An district, Xiamen city, Fujian Province. China.. Product Name: Distance monitoring bracelet Model Number: IVF-BT01 FCC Identifier: 2ABREIVF-BT01 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Zhiming Zhong Date: 2020-07-29 Title: R & D Manager Signature of applicant:

C5266091_X10_Ed.2 1/1 Xiamen Innov Information Technology Co.,LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2020-07-29 Subject: Request for Confidentiality FCC ID: 2ABREIVF-BT01 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ■☐ Schematics ■☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ■ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long‐Term Confidentiality may be permitted under special conditions (See II. LONG‐TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short‐Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Zhiming Zhong Title: R & D Manager

External Photo FCC ID: 2ABREIVF-BT01

Label and label location

Internal Photo BT ANT FCC ID: 2ABREIVF-BT01

FCC RF Exposure FCC ID: 2ABREIVF-BT01 Applicant: Xiamen Innov Information Technology Co.,LTD. Exposure category: General population/uncontrolled environment EUT Type: Distance monitoring bracelet Device Type: Portable Device FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations:“ Unless specifically required by the published RF exposure KDB procedures, standalone 1‐g head or body and 10‐g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source‐based time‐averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune‐up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two‐way radios, handsets, laptops & tablets etc.23 “[(max. power of channel, including tune‐up tolerance, mW)/ (min. test separation distance, mm)] ∙ [√f (GHz)]≤ 3.0 for 1‐g SAR and ≤ 7.5 for 10‐g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is <5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. Maximum Conducted Power Results Bluetooth BLE Channel Channel 0 Channel 19 Channel 39 Test Results(dBm) ‐3.875 -3.936 -3.933 Target (dBm) ‐4 ‐4 ‐4 Tolerance ±(dB) ±1 ±1 ±1 Maximum Evaluation Results Bluetooth Channel Fre.(MHz) Antenna Distance （mm） RF output power (including tune‐up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW 39 2480 5 ‐3 0.501 0.158＜3.0 Yes Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB447498 D01 General RF Exposure Guidance v06.

Report No.: SET2020-05575 CCIC-SET/ TRF:IRF(2019-05-23) Page 1 of 31 RF TEST REPORT Report No.: SET2020-05575 Product Name: Distance monitoring bracelet FCC ID: 2ABREIVF-BT01 Model No. : IVF-BT01 Applicant: Xiamen Innov Information Technology Co.,LTD Address: No.943, Tonglong Second RD, Hongtang Town, Tong an District, Xiamen city, Fujian Province. Dates of Testing: 07/11/2020 —07/21/2020 Issued by: CCIC Southern Testing Co., Ltd. Lab Location: Electronic Testing Building, No. 43 Shahe Road, Xili Street, Nanshan District, Shenzhen, Guangdong, China. Tel: 86 755 26627338 Fax: 86 755 26627238 This test report consists of 31 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CCIC-SET. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers, reviewer and approver. Any objections must be raised to CCIC-SET within 20 days since the date when the report is received. It will not be taken into consideration beyond this limit. Report No.: SET2020-05575 CCIC-SET/ TRF:IRF(2019-05-23) Page 3 of 31 TABLE OF CONTENTS RF TEST REPORT ....................................................................................................................... 1 1. GENERAL INFORMATION ................................................................................................. 5 1.1. EUT Description .................................................................................................................... 5 1.2. Test Standards and Results ..................................................................................................... 6 1.3. Table for Supporting Units ..................................................................................................... 7 1.4. Facilities and Accreditations .................................................................................................. 8 2. 47 CFR PART 15C REQUIREMENTS ................................................................................. 9 2.1. Antenna requirement .............................................................................................................. 9 2.2. Peak Output Power............................................................................................................... 10 2.3. 6dB and 99% Occupied Bandwidth ..................................................................................... 11 2.4. Conducted Band Edges and Spurious Emissions ................................................................. 12 2.5. Power spectral density (PSD) .............................................................................................. 14 2.6. Radiated Band Edge and Spurious Emission ....................................................................... 16 3. LIST OF MEASURING EQUIPMENT .............................................................................. 24 4. UNCERTAINTY OF EVALUATION .................................................................................. 25 APPENDIX A ............................................................................................................................... 26 Report No.: SET2020-05575 CCIC-SET/ TRF:IRF(2019-05-23) Page 4 of 31 Change History Issue Date Reason for change 1.0 2020.07.21 First edition Report No.: SET2020-05575 CCIC-SET/ TRF:IRF(2019-05-23) Page 5 of 31 1. General Information 1.1. EUT Description EUT Type Distance monitoring bracelet Frequency Range Bluetooth LE 2402MHz~2480MHz Channel Number Bluetooth LE 40 Bit Rate of Transmitter Bluetooth LE 1Mbps Modulation Type Bluetooth LE GFSK Power supply DC 3V from CR2477 T Coin Battery Antenna Type Internal Antenna Gain 0dBi Note 1: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Note 2: The EUT was programmed to be in continuously transmitting mode and the transmit duty cycle is not less than 98%. Report No.: SET2020-05575 CCIC-SET/ TRF:IRF(2019-05-23) Page 6 of 31 1.2. Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C (Bluetooth, 2.4GHz ISM band radiators) for the EUT FCC Certification: No. Identity Document Title 1 47 CFR Part 15 Subpart C 2017 Radio Frequency Devices 2 ANSI C63.10-2013 American National Standard for Testing Unlicensed Wireless Devices Test detailed items/section required by FCC rules and results are as below: No. Section in CFR 47 Description Result 1 15.203 Antenna Requirement PA S S 2 15.247(b) Peak Output Power PASS 3 15.247(a) Bandwidth PASS 4 15.247(d) Conducted Band Edges and Spurious Emission PA S S 5 15.247(e) Power spectral density (PSD) PASS 6 15.207 Conducted Emission PASS 7 15.209 15.205 15.247(d) Radiated Band Edges and Spurious Emission PA S S The tests of Conducted Emission and Radiated Emission were performed according to the method of measurements prescribed in ANSI C63.10-2013. These RF tests were performed according to the method of measurements prescribed in KDB 558074D01 v05r02. 40 channels are provided for Bluetooth LE Channel Frequency(MHz) Channel Frequency(MHz) 0 2402 20 2442 1 2404 21 2444 2 2406 22 2446 3 2408 23 2448 4 2410 24 2450 5 2412 25 2452 6 2414 26 2454 7 2416 27 2456 8 2418 28 2458 9 2420 29 2460 10 2422 30 2462 11 2424 31 2464 Report No.: SET2020-05575 CCIC-SET/ TRF:IRF(2019-05-23) Page 7 of 31 12 2426 32 2466 13 2428 33 2468 14 2430 34 2470 15 2432 35 2472 16 2434 36 2474 17 2436 37 2476 18 2438 38 2478 19 2440 39 2480 Bluetooth LE Test Items Modulation Channel Peak Conducted Output Power Power Spectral Density 6dB Bandwidth Conducted and Spurious Emission Radiated and Spurious Emission GFSK 0/20/39 Band Edge GFSK 0/39 1.3. Table for Supporting Units No. Equipment Brand Name Model…

Text truncated - open the document above for the full version.

15C setup FCC ID: 2ABREIVF-BT01