2ABSL1101RFID SECURITY TRANSMITTER

Passive or Active Keyless entry system User Guide 8 Lightwave Technology 400 Wright Street Montreal, QC, Canada, H4N1M6 Website: www.lightwavetechnology.com Passive Keyless Entry System Doc#140109 Rev: 1.0 ©2014 -1W-AM-2BTN-PKE-A- Canada OWNERS MANUAL PKE-AL(PS)-UNI WARNING! It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner. A note concerning the battery inside the transmitter: Depending on your usage of the transmitter, the battery can last anywhere between 2 to 3 years. Although we recommend to replace the battery inside the transmitter every year to get the best performances from your system. INDUSTRY CANADA USER NOTICE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. Passive or Active Keyless entry system User Guide 2 Table of Contents Government regulations.............................................................................. . ...... 3 Using the transmitter and ADB.................................................................. . ...... 4 Doorlock Access Chart................................................................................. . ...... 5 Trunk / Hatch Release................................................................................. . ...... 6 Valet Mode............................................................................................. . ............... 6 Parking Light Flash Table.................................................................................... 7 Passive or Active Keyless entry system User Guide 7 Diagnostics - Parking lights Flash Table Parking Lights Flashes Description 1 Flash - Door Lock 2 Flashes - Door Unlock 3 Flashes - Valet Mode 5 Flashes - Please see your retailer 6 Flashes - Please see your retailer 7 Flashes - Door Locking command using ADB while RFID transmitter is inside vehicle (Active Mode Only) 8 Flashes - Please see your retailer Trunk/Hatch Release or Motorized liftgate With RFID transmitter Press & Release Button 1 & 2 on RFDI transmitter - Parking lights will blink 2 times - Trunk will pop open or Motorized hatch will open or Close Valet Mode Enabled/Disabled Use factory key in ignition cylinder Cycle Key in ignition cylinder 5x On/Off - Valet On = Parking lights will blink 3 times - Valet Off = Parking lights will blink 2 times Passive or Active Keyless entry system User Guide Passive or Active Keyless entry system User Guide Government regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized only on a no-interference, no- protection basis; in other words, this device must not be used if it is determined that it causes harmful interferences to services authorized by IC. In addition, the user of this device must accept any radio interface that may be received, even if this interfere-ence could affect the operation of the device. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. 6 3 IC RSS-GEN, Sec 7.1.3 Warning Statement- (Required for license-exempt devices) ENGLISH: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FRENCH: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. IC RSS-GEN, Sec 7.1.2 Warning Statement- (Required for Transmitters) ENGLISH: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the …

Text truncated - open the document above for the full version.

LIGHTWAVE TECHNOLOGY Lightwave Technology 400 Wright Street, St-Laurent, QC, H4N-1M6 Tel 514-745-6265 | Fax 514-745-6068 www.lightwavetechnology.com January 29, 2014 Equipment Authorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Model: LWM-1101; LWM-1111 FCC ID: 2ABSL1101 IC: 11732A-LWM1101 Re: Request of Confidentiality Pursuant to FCC 47 CRF Sections 0.457(d) and 0.459 and IC RSP-100, Section 10, of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: • Schematics • Block Diagrams • Operational Discriptions The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d) (1) (ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. Sincerely, Ismail Warsame RF Design Engineer

LIGHTWAVE TECHNOLOGY /LJKWZDYH7HFKQRORJ\ :ULJKW6WUHHW6W/DXUHQW4&+10 7HO_)D[ ZZZOLJKWZDYHWHFKQRORJ\FRP External Photos:  0RGHO/:0/:0 ,&$/:0 )&&,'$%6/    3LFWXUH([WHUQDO7RS9LHZ    3LFWXUH([WHUQDO%RW9LHZ

Internal Photos: LIGHTWAVE TECHNOLOGY Model: LWM-1101; LWM-1111 IC: 11732A-LWM1101 FCC ID: 2ABSL1101 Picture 1: Internal Top View Picture 2: Internal Bot View Lightwave Technology 400 Wright Street, St-Laurent, QC, H4N-1M6 Tel 514-745-6265 | Fax 514-745-6068 www.lightwavetechnology.com

FCC PART 15.209 LOW POWER TRANSMITTER TEST REPORT Applicant LIGHTWAVE TECHNOLOGY Address 400 WRIGHT STREET ST-LAURENT QUEBEC CANADA FCC ID 2ABSL1101 Product Description RFID TRANSMITTER Date Sample Received 2/7/2014 Date Tested 3/11/2014 Report Issue Date 3/12/2014 Tested By Cory Leverett Approved By Cory Leverett Report Number 190AUT14TestReport Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW State Road 45 Newberry, Fl 32669 USA Phone: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: [email protected] Website: www.timcoengr.com APPLICANT: LIGHTWAVE TECHNOLOGY FCC ID: 2ABSL1101 REPORT: L\LIGHT_2ABSL\190AUT14\190AUT14TestReport Page 2 of 14 CONTENTS GENERAL REMARKS....................................................................................................................... 3 REPORT SUMMARY ........................................................................................................................ 4 TEST ENVIRONMENT ...................................................................................................................... 4 TEST SETUP SUMMARY .................................................................................................................. 4 EUT SPECIFICATION ....................................................................................................................... 5 TEST EQUIPMENT LIST................................................................................................................... 6 TEST PROCEDURES ....................................................................................................................... 7 RADIATED SPURIOUS EMISSIONS .................................................................................................. 8 OCCUPIED BANDWIDTH ............................................................................................................... 11 POWER LINE CONDUCTED INTERFERENCE ................................................................................. 13 APPLICANT: LIGHTWAVE TECHNOLOGY FCC ID: 2ABSL1101 REPORT: L\LIGHT_2ABSL\190AUT14\190AUT14TestReport Page 3 of 14 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. The test results relate only to the items tested. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025: 2005 requirements. I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Cory Leverett Engineering Project Manager Date: March 12, 2014 APPLICANT: LIGHTWAVE TECHNOLOGY FCC ID: 2ABSL1101 REPORT: L\LIGHT_2ABSL\190AUT14\190AUT14TestReport Page 4 of 14 REPORT SUMMARY Disclaimer The test results only relate to the item tested. Applicable Rule(s) Pt 15.209, Pt 15.107, ANSI C63.4: 2003 Related Report 190BUT14 TEST ENVIRONMENT Test Facility Timco Engineering, Inc. 849 NW State Road 45 Newberry, FL 32669 USA. Test Condition in the laboratory Temperature: 26ºC Relative humidity: 50% TEST SETUP SUMMARY Test Setup Diagram/ Description The DUT was placed on the turntable per setup per ANSI C63.4: 2003. A test set up photo is provided for clarification. Deviation from the standard/procedure No deviation Modification of DUT No modification APPLICANT: LIGHTWAVE TECHNOLOGY FCC ID: 2ABSL1101 REPORT: L\LIGHT_2ABSL\190AUT14\190AUT14TestReport Page 5 of 14 EUT SPECIFICATION EUT Description RFID TRANSMITTER FCC ID 2ABSL1101 Tuned Frequency 125KHz EUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable Laboratory Test Conditions Temperature: 26ºC Humidity: 55% Modifications to DUT: No Yes (explanation below) EUT Supporting Cables Cable Type Connector Manufacturer Length Unshielded 22AWG OFC Black 6 PIN / Push to Start Button N/A 1M Unshielded 22AWG OFC Black 12 PIN / Main Power Harness N/A .9M Unshielded 14AWG OFC White 4 PIN / Internal relay Harness N/A .9M Unshielded 22AWG OFC Dual Black 4 PIN N/A .5M Unshielded 22AWG OFC Brown 6 PIN Aux Harness N/A .9M Unshielded 22AWG OFC Red 2 PIN 125 KHz Ferrite ANT Cable N/A 2.5M Unshielded 18AWG OFC Soldered Black 12 PIN for Power Connection N/A 1M APPLICANT: LIGHTWAVE TECHNOLOGY FCC ID: 2ABSL1101 REPORT: L\LIGHT_2ABSL\190AUT14\190AUT14TestReport Page 6 of 14 TEST EQUIPMENT LIST Device Manufacturer Model Serial Number Cal/Char Date Due Date DC Power Supply H/P 6286A 1744A03842 N/A N/A Field Strength Software TEI Version 4.0 N/A N/A N/A Signal Generator HP 8640B 2308A21464 02/23/12 02/23/14 EMI Test Receiver *Rhode & Schwarz ESIB 40 100274 03/13/12 03/16/14 3/10-Meter OATS TEI N/A N/A 3/31/11 3/31/14 3-Meter Semi- Anechoic Chamber Panashield N/A N/A 12/31/13 12/31/15 Antenna: Biconnical Eaton 94455-1 1057 06/14/13 06/14/15 Antenna: Log-Periodic Eaton 96005 1243 05/31/13 05/31/15 Antenna: Passive Loop EMC Test Systems EMCO 6512 9706-1211 6/14/12 6/14/14 Analyzer Tan Tower Preamplifier HP 8449B-H02 3008A00372 01/15/14 01/15/16 Analyzer Tan Tower Quasi-Peak Adapter HP 85650A 3303A01690 01/15/14 01/15/16 Analyzer Tan Tower RF Preselector HP 85685A 3221A01400 01/15/14 01/15/16 Analyzer Tan Tower Spectrum Analyzer HP 8566B Opt 462 3138A07786 3144A20661 01/15/14 01/15/16 *EMI RECEIVER SOFTWARE VERSION The receiver firmware used was versi…

Text truncated - open the document above for the full version.