2ABUE-BP200-2-2-1BP200-2-2-1

Wi‐MM BP200 Users Manual (Page1) Wi‐MM’s BP200 is a state of the art battery powered asset tracker and sensor platform adaptable to a wide variety of applications including: bicycle fleet management, cargo tracking, and mobile asset security. The small and versatile BP200 can be powered or charged from a wide range of power sources: +5V to +50V AC or DC or from a solar panel. The BP200 is used in conjunction with the Wi‐MM web Dashboard. Each BP200 has unique cellular network credentials, an assembly serial number, and a set of identification values linked to the asset associated with the particular BP200. All identification information and cellular network provisioning should be coordinated with Wi‐MM Customer Service prior to deploying the unit. The BP200 charge indication LED will light RED, when the unit is charging. Full charge is achieved when the RED LED goes off and the adjacent GREEN LED goes on. If the battery is fully depleted, it will take 3 to 4 hours for the unit to full re‐charge. The charge state of the battery at any given time is dependant upon the particular application. For security applications, the BP200 can remain dormant for more than two months and then wake up based on an accelerometer triggered event. For bike fleet applications, wired recharging can be eliminated and power for the unit can be derived from a dynamo hub generarator or solar panel. For battery power conservation, the BP200 will default to sleep mode, if none of the stimuli listed below are present. The BP200 can be factory configured to awaken based on any combination of: ƒ Accelerometer Trigger = Physical Movement ƒ Dynamo Generator Output Present = Wheel Turning ƒ API call from customer application = Kiosk Checkout Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1 Wi‐MM BP200 Users Manual (Page2) GPS (Yellow). Blinks when the unit is awake and GPS is active = 1 PPS GPS Output Lock (Red) When the alarm is set (on) this LED will blink Battery (Orange) Off when the battery level is OK Blinking when the battery level is low Logging & Mapping (Green) Blinks when the BP200 is logging and mapping GPS data. USB Charging Port Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1 Dynamo Hub & General Purpose Power Input +5V to +50V AC or DC Connector = JST PH 2 Pin Solar Panel Input (5 to 10V OC) Connector = JST PH 2 Soft Reset Button Hard Reset Button Charge Indicator LEDs Wi‐MM BP200 Users Manual (Page3) The BP200 is cloud connected to the Wi‐MM network management center through a cellular wireless network. Sensor functional capability includes: ƒ Logging and Mapping GPS location ƒ Acceleration ƒ Relative Altitude (based on on‐board pressure sensor) ƒ Temperature ƒ Cell Network Signal Level The system also includes an alarm function that can be set or triggered remotely through the Dashboard. The alarm function includes an audible 100 dB buzzer, and automatic text and email notifications to registered administrators in addition to display alerts on the Dashboard. Alarms can be configured to can be triggered based on any combination of the following factors: ƒ Tamper detection based on motion sensing ƒ Excessive Speed ƒ Violation of a Geo‐Fence The BP200 can be reset to factory installed firmware by holding the soft reset button for about five seconds and then releasing. After a two tone sound, all LEDs will flash and the system will restart. The restart process may take up 30‐60 seconds as the system connects to the cellular network and acquires the GPS signal. The restart process is complete when the unit beeps once and the GPS LED (Yellow) begins to flash continuously. Manufacturer: Wi-MM Corp. Model: BP100-2-2-1 FCC ID: 2ABUE-BP100-2-2-1 IC: 11915A-BP100221 Model BP100-2-2-1 Wi‐MM BP200 Users Manual (Page4) REGULATORY NOTICE This equipment is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government and Industry Canada. Compliance with FCC and IC RF exposure rules has been evaluated for mobile or fixed use cases only with minimum distance of 20cm from human bodies. The device is not approved for use at closer distances. This device complies with IC RSS Rules and FCC Part 15. Operation is subject to the following conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Modifications to this equipment not authorized by Wi-MM may void its approval for operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Manufacturer: Wi-MM Corp. Model: BP400-2-2-1 FCC ID: 2ABUE-BP400-2-2-1 IC: 11915A-BP400221 Model BP400-2-2-1 Manuel de l'utilisateur Wi‐MM BP200 (Page1) Le BP200 de Wi‐MM est un état de la batterie de l'art alimenté tracker actif et le capteur plateforme ada…

Text truncated - open the document above for the full version.

To Whom It May Concern: Subject: Product Equality Declaration Letter (BP200 vs. BP100) WE, Wi-MM Corporation, 1885 De La Cruz Blvd., Santa Clara, CA 95050 declare that: Wi-MM Model BP200-2-2-1 [FCC ID: 2ABUE-BP200-2-2-1 & IC: 11915A-BP200221] uses the same circuits, modules, and RF items as previously certified Wi-MM Model BP100-2-2-1 [FCC ID: 2ABUE- BP100-2-2-1 & IC: 11915A-BP100221]. The BP200-2-2-1 combines the same items into a different form factor and adds a versatile power supply allowing the unit to be power or re-charged from a wide variety of power sources. Same Items: CDMA Cell Module Module Manufacturer: U-Blox Module Description: LISA-C200 CDMA 800/1900 MHz module FCC Identifier: R5Q-LISAC200 IC Identifier: 8595B-LISAC200A Module Test Report: 12/20/12 Bluetooth Module Module Manufacturer: BlueGiga Technologies Module Description: Bluetooth 4.0 Module FCC Identifier: QOQBLE113 IC Identifier: 5123A-BGTBLE113 Module Test Report: SGS Reference Number 268252, Date submitted to FCC 4/30/13 Cellular Antenna Manufacturer: Taoglas Description: PA.25 Hexaband Antenna BP200 Host Equipment Identification: Leslie Levitt, CTO Dated: 4-02-15 Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1

To Whom It May Concern: Subject: Validity of Test Results from Testing / Certification of the integrated Module WE, Wi-MM Corporation, 1885 De La Cruz Blvd., Santa Clara, CA 95050 confirm that the results from conducted tests applied to the radio modules CDMA Cell Module Module Manufacturer: U-Blox Module Description: LISA-C200 CDMA 800/1900 MHz module FCC Identifier: R5Q-LISAC200 IC Identifier: 8595B-LISAC200A Module Test Report: Report Number: 2012 04203246 FCC issued: April 11, 2012 by Nemko USA Inc. Bluetooth Module Module Manufacturer: BlueGiga Technologies Module Description: Bluetooth 4.0 Module FCC Identifier: QOQBLE113 IC Identifier: 5123A-BGTBLE113 Module Test Report: Report Number: 268252-1 issued: April,26, 2013 by: SGS Fimko Ltd. which are incorporated in our host equipment and as reported in module test report(s) noted above accurately represent the test results under the new conditions when the identified radio modules are integrated in the identified host equipment. By integration of the said radio modules into the identified host equipment no changes were made to it or by external adaptation circuitry that impacts the validity of the results of the original module’s test reports. Leslie Levitt, CTO Dated: 5-04-15 Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1

Receiver Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Subject: Request for Permanent Confidentiality FCC ID: 2ABUE-BP200-2-2-1 To Whom It May Concern: In accordance with §0.457(d) and §0.459 of CFR 47, Wi-MM Inc. requests permanent confidentiality for the following items 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational Description These items contain detailed system and equipment description and related information about the product which Wi-MM Inc. considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. The circuit board is inside a sealed housing only serviceable by Wi-MM Inc. Since this design is a basis from which future technological products will evolve, Wi-MM Inc. also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Best Regards, May 01 2015, Santa Clara CA

WI-MM SIZE A CAGE CODE DWG. NO. Certification BP200 REV. B PAGE 59 26.0 EXTERNAL PHOTOS Top Bottom Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1 USB In (DC only) Slot for Alternative Wired DC input WI-MM SIZE A CAGE CODE DWG. NO. Certification BP200 REV. B PAGE 60 Bottom (with Label) There are no accessories. Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1

WI-MM SIZE A CAGE CODE DWG. NO. Certification BP200 REV. B PAGE 25 12.0 TUNE UP PROCEDURE There is no tuning or tune up procedure since the design is based on pre-tested modules. 13.0 LABEL ID & LOCATION INFO The label is located on the back of the unit where shown below. FCC ID: 2ABUE-BP200-2-2-1 IC: 1195A-BP200221 Model BP200-2-2-1 14.0 USERS MANUAL [see the following pages from Wi-MM BP200 Users Manual 3-16-15.doc] Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1

WI-MM SIZE A CAGE CODE DWG. NO. Certification BP200 REV. B PAGE 19 9.0 INTERNAL PHOTOS Top of Printed Circuit Assembly Bottom of Printed Circuit Assembly (Battery not Installed) Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1 Cell Antenna Cell Module Bluetooth Module WI-MM SIZE A CAGE CODE DWG. NO. Certification BP200 REV. B PAGE 20 Bottom of Printed Circuit Assembly (Battery Installed) Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC: 11915A-BP200221 Model BP200-2-2-1

FCC: Accredited IC recognized # 3462B-1 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V1.0 © Copyright by CETECOM RF Exposure Evaluation Report FOR: Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC Certification Number: 11915A-BP200221 FCC CFR 47 Part 1.1310, 2.1091 IC RSS-102, Issue 5 TEST REPORT #: EMC-WIMML-004-15001-FCCICMPE DATE: 04/30/2015 Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 2 of 12 1 Assessment The following equipment, as detailed in section 3 of this test report, meets the RF exposure limits and/or the conditions for exemption from routine evaluation as defined in the following standards. Standard Version FCC CFR 47 Part 1.1310 Current as of [04/16/2015] FCC CFR 47 Part 2.1091 Current as of [04/16/2015] FCC KDB 447498 v05r02 OET Bulletin 65 Edition 97-01, August 1997 RSS 102 Issue 5 Responsible for Testing Laboratory: 2015-04-30 Compliance Franz Engert (Manager Compliance) Date Section Name Signature Responsible for the Report: 2015-04-30 Compliance Douglas Antioco (EMC Engineer) Date Section Name Signature The test results of this test report relate exclusively to the test item specified in Section 3. CETECOM Inc. USA does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CETECOM Inc. USA. Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 3 of 12 2 Administrative Data 2.1 Identification of the Testing Laboratory Issuing the Test Report Company Name CETECOM Inc. Department Compliance Address 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Telephone +1 (408) 586 6200 Fax +1 (408) 586 6299 Test Lab Manager Josie Sabado Project Manager Franz Engert Test Engineer Douglas Antioco 2.2 Identification of the Client Client Company Wi-MM Inc. Street Address 1885 De La Cruz Blvd. Suite 205 City, State, Zip Code Santa Clara, CA, 95050 Country USA 2.3 Identification of the Manufacturer Manufacturer Company Same as client Street Address City, State, Zip Code Country Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 4 of 12 3 Equipment under Test (EUT) 3.1 Specification of the Equipment under Test Model Number BP200-2-2-1 Hardware Version BP200 HW-2-2-1 Software Version BP200 SW-1.0 FCC ID 2ABUE-BP200-2-2-1 IC Certification Number 11915A-BP200221 Technical Product Description battery powered asset tracker and sensor platform Radios Included 1. U‐Blox LISA‐C200 Pre‐certified Wireless Module FCC ID R5Q ‐ LISAC200 2. Bluegiga BLE‐113 Pre‐certified module Antenna integrated on module FCC ID QQQBLE113 3. U‐Blox MAX‐7C Dual SAW filter + LNA front end Assisted GPS capability for fast start Antenna Information 1. hexa-band cellular SMD antenna TAOGLAS 824 MHz: 1.5 dBi; 1850 MHz: 2.4 dBi 2. Integrated ceramic chip: 0.5 dBi Co-located Transmitters/ Antennas All of the above transmitters and antennas are collocated Rated Operating Voltage Range AC: 5V-50V DC: 5V-10V Rated Operating Temperature Range -20degC to +65degC Prototype / Production Unit Prototype Device Category ☐ Fixed Installation ☒ Mobile ☐ Portable Exposure Category ☐ Occupational/ Controlled ☒ General Population/ Uncontrolled Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 5 of 12 3.2 Description of Functions and Data Ports Function # Type Exercise Method 1 NA USB port is used for charging only. 3.3 Identification of the Equipment Under Test (EUT) EUT # Serial Number Hardware Version Software Version Comments 1 3158 4214 0117 BP200 HW-2-2-1 BP200 SW-1.0 3.4 Identification of Accessory equipment (AE) AE # Type Serial Number Manufacturer Model Comments 1 Shielded USB cable Type A to micro USB 2 USB charger 13221001004 Salcomp SC1402 3.5 Identification of Test Support Equipment (TSE) TSE # Type Serial Number Manufacturer Model Comments 1 3.6 Environmental Conditions during test The following environmental conditions were maintained during the course of testing: Ambient Temperature: 22degC Relative humidity: 15% Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 6 of 12 3.7 Miscellaneous Testing Information The following screenshots are taken from the data sheets that have been used as reference: Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 7 of 12 Test Report #: EMC-WIMML-004-15001_FCCICMPE FCC ID: 2ABUE-BP200-2-2-1 Date of Report : 2015-04-20 IC Cert. No.: 11915A-BP200221 Page 8 of 12 4 RF Exposure Evaluation Requirements 4.1 FCC: Calculations can be made to predict RF field strength and power density levels around typical RF sources using the general equations (3) and (4) on page 19 of the following FCC document: “OET Bulletin 65, Edition 97-01 - Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields”. The table below is excerpted from Table 1B of CFR 47 1.1310 titled Limits for Maximum Permissible Exposure (MPE), Limits for General Population/Uncontrolled Exposure: Frequency Range (MHz) Power density (mW/cm 2 ) Averaging time (minutes) 300 – 1500 f (MHz) /1500 30 1500 – 100.000 1.0 30 Using the equation from page 19 of OET Bulletin 65, Edition 97-01: 2 4R PG S   where:…

Text truncated - open the document above for the full version.

FCC: Accredited IC recognized # 3462B-1 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V1.01 2013-07-29 © Copyright by CETECOM FCC/IC Test Report FOR: Wi-MM Corporation Model: BP100-2-2-1 Product Description: Bike Computer with location, alarm and performance information FCC ID: 2ABUE-BP100-2-2-1 IC Certification Number: 11915A-BP100221 47 CFR Part 2, 22, 24 RSS-GEN issue 3 RSS-132 Issue 3 RSS-133 Issue 6 TEST REPORT #: EMC_ WIMML_002_14001_BP-100_FCC_22_24_Rev1 DATE: 2014-07-09 Test Report #: EMC_WIMML_002_14001_BP-100_FCC_22_24_Rev1 FCC ID: 2ABUE-BP100-2-2-1 Date of Report : 2014-07-09 IC ID: 11915A-BP100221 Page 2 of 42 Table of Contents 1 Assessment ............................................................................................................................... 3 2 Administrative Data ................................................................................................................. 4 2.1 Identification of the Testing Laboratory Issuing the Test Report .................................................. 4 2.2 Identification of the Client ............................................................................................................. 4 2.3 Identification of the Manufacturer ................................................................................................. 4 2.4 Dates of Testing: ............................................................................................................................ 4 3 Equipment under Test (EUT) ................................................................................................... 5 3.1 Specification of the Equipment under Test .................................................................................... 5 3.2 Identification of the Equipment under Test (EUT) ........................................................................ 5 3.3 Identification of Accessory equipment........................................................................................... 6 4 Summary of Measurement Results .......................................................................................... 7 5 Measurements........................................................................................................................... 9 5.1 Measurement Uncertainty .............................................................................................................. 9 5.7 RF Power Output ..................................................................................................................... 10 5.7.1 References ............................................................................................................................ 10 5.7.2 Limits: .................................................................................................................................. 10 5.7.3 Conducted Output Power Verification ................................................................................. 11 5.7.4 RF Power Output ................................................................................................................. 12 5.8 Spurious Emissions Radiated ............................................................................................. 20 5.8.1 References ............................................................................................................................ 20 5.8.2 Limits: .................................................................................................................................. 20 5.8.3 Radiated out of band measurement procedure: ................................................................... 22 5.8.4 Sample Calculations for Radiated Measurements ............................................................... 23 5.8.5 Spectrum Analyzer Settings .................................................................................................. 23 5.8.6 Test Results: ......................................................................................................................... 25 6. Test Equipment and Ancillaries used for tests ....................................................................... 40 6 Block Diagrams ...................................................................................................................... 41 7 Revision History ..................................................................................................................... 41 Test Report #: EMC_WIMML_002_14001_BP-100_FCC_22_24_Rev1 FCC ID: 2ABUE-BP100-2-2-1 Date of Report : 2014-07-09 IC ID: 11915A-BP100221 Page 3 of 42 1 Assessment The following equipment as further described in section 3 of this test report was evaluated against the applicable criteria specified in FCC CFR47 Parts 2, 22 and 24 & Industry Canada Radio Standard Specifications RSS-GEN Issue 3, RSS-132 Issue 3 and RSS-133 Issue 6. No deviations were ascertained during the course of the tests performed. Company Description Model # Wi-MM Corporation Bike computer with location, alarm and performance information BP100-2-2-1 Report reviewed by: 2014-07-09 Compliance Josie Sabado (Test Lab Manager) Signing on the behalf of Franz Engert (Compliance Manager) Date Section Name Signature Responsible for the Report: 2014-07-09 Compliance Douglas Antioco (EMC Engineer) Date Section Name Signature The test results of this test report relate exclusively to the test item specified in Section3. CETECOM Inc. USA does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the pri…

Text truncated - open the document above for the full version.

Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 CERTIFICATION TEST REPORT Applicant: U-Blox 12626 High Bluff Drive, Suite 200 San Diego, CA 92130 Equipment Under Test (EUT): CDMA 1xRTT Module Model: LISA-C200 FCC ID: XU9-LISAC200 IC ID: 8694A-LISAC200 In Accordance With: FCC Part 22, Subpart H RSS-132, Issue 2 September 2005 FCC Part 24 Subpart E RSS 133 Issue 5 February 2009 RSS GEN Issue 3 December 2010 Tested By: Nemko USA Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Date: April 11, 2012 Report Number: 2012 04203246 FCC Project Number: 10222569 Nex Number: 203246 Total Number of Pages: 54 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-LISAC200 Report Number: 2012 04203246 FCC IC: 8649A-LISAC200 Page 2 of 52 Section 1: Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC rules parts CFR47 Part 2 and 24 subpart E for the United States and RSS132 Issue 2, RSS133 Issue 5, and RSS-Gen Issue 3 for Canada. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC and IC. The assessment summary is as follows: Apparatus Assessed: CDMA 1xRTT Module Model: LISA-C200 Serial: A10000157EFF5A, A10000157EFF49 Specifications: FCC Part 22, Subpart H Industry Canada RSS-132, Issue 2, September 2005 FCC Part 2, Part 24 Subpart E RSS 133 Issue 5, February 2009 RSS-GEN Issue 3 December 2010 Date Received in Laboratory: March 19, 2012 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-LISAC200 Report Number: 2012 04203246 FCC IC: 8649A-LISAC200 Page 3 of 52 1.1 Report Release History REVISION DATE COMMENTS - APRIL 11, 2012 Prepared By: Andreas Gillmeier - APRIL 11, 2012 Initial Release: Alan Laudani Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. TESTED BY: Date: APRIL 11, 2012 Andreas Gillmeier, Sr. EMC Wireless Engineer Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-LISAC200 Report Number: 2012 04203246 FCC IC: 8649A-LISAC200 Page 4 of 52 TABLE OF CONTENTS Section 1: Summary of Test Results ............................................................................... 2 1.1 Report Release History ..................................................................................... 3 Section 2: Equipment Under Test ................................................................................... 5 2.1 Product Identification ........................................................................................ 5 2.2 Technical Specifications of the EUT ................................................................. 5 Section 3: Test Conditions .............................................................................................. 6 3.1 Test Environment ............................................................................................. 6 3.2 Test Equipment ................................................................................................ 6 Section 4: Observations .................................................................................................. 7 4.1 Modifications Performed During Assessment ................................................... 7 4.2 Record Of Technical Judgments ...................................................................... 7 4.3 EUT Parameters Affecting Compliance ............................................................ 7 4.4 Test Deleted ..................................................................................................... 7 4.5 Additional Observations .................................................................................... 7 Section 5: Results Summary ........................................................................................... 8 5.1 Test Result summary table ............................................................................... 8 Appendix A: Test Results ................................................................................................ 9 A1. Powerline conducted emissions ....................................................................... 9 A2. RF Power Output ............................................................................................ 18 A3. Occupied Bandwidth ....................................................................................... 25 A4. Spurious Emissions At Antenna Terminals ..................................................... 33 A5. Field strength of Spurious Emissions ............................................................. 40 A6. Frequency Stability ......................................................................................... 45 A7. Receiver Spurious .......................................................................................... 48 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3…

Text truncated - open the document above for the full version.

FCC: Accredited IC recognized # 3462B-1 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V2.0.1 3/20/2015 © Copyright by CETECOM FCC/IC Test Report FOR: Manufacturer: Wi-MM Corp. Model: BP200-2-2-1 FCC ID: 2ABUE-BP200-2-2-1 IC ID: 11915A-BP200221 FCC Part 15B ICES-003 TEST REPORT #: EMC-WIMML-004-15001-15B DATE: 04/14/2015 Test Report #: EMC-WIMML-004-15001-15B FCC ID: 2ABUE-BP200-2-2-1 Date of Report: 04/14/2015 IC Cert. No. 11915A-BP200221 Page 2 of 24 TABLE OF CONTENTS Assessment ________________________…

Text truncated - open the document above for the full version.