2ABYQFSV1251ULTRAMICRO FPV CAMERA

www.fatshark.com UltraMicro FPV Camera Operation manual/specification REV A Overview: The UltraMicro FPV camera is a micro VGA imager paired with digital to analog converter and micro transmitter for use with ultralight RC airframes. Its 1S (3.5-4.5) volt input is designed to share onboard power supply with the micro craft (commonly powered off 1S lipo packs). The camera has DC-DC step up regulator to ensure proper operation even if supply voltage drops due to air frame demand. Low power transmitter allows for FCC license free use and is suitable for indoor and short range performance. Electrical: Power supply: 3.3-5.5V (1S supply) Power consumption: 300mA @ 3.7V (1S) Imager: 1/6” VGA CMOS Lens: 0.95mm IR cut 115ediagonal FOV (90ehorizontal) Operation: -10 to 60C Mechanical: Square: 13.2 X 17.6 X 9mm Lens extrude: 9mm X 10mm diameter Antenna extrude: 20mm X 25mm diameter Weight: 3.5g Packaging Dimensions: bag 50 x 70 mm Weight: (approximately 16g) System: Analog NTSC video out Interface: Single push button channel control (1-7 then back to ch 1) 2p male 1.25mm JST (power, ground) Indicators: Solid LED for noting power on Channel select LED flashes on channel change (Channel LED is solid on channel 1 only) Operating Frequencies: 5740 MHz, 5760 MHz, 5780 MHz, 5800 Mhz, 5820 MHz 5840 Mhz 5860 MHz Operation When power is applied (3.3 – 5.5V) the camera and transmitter are powered. The camera has memory so the transmitter will power up in the last used channel. The top LED shows the camera has power and the lower LED flashes when channel is changed (by depressing button). The channels scroll sequentially from ch 1-7 (and back to 1). Only on channel 1 is the channel indicator a solid light. Detailed Operation Image is focused onto the 1/6” digital imager via the 0.95m lens. The lens has an IR filter to condition the light entering the imager to optimize image color. The camera board has an A/D conversion circuit that converts the VGA digital imager signal into an NTSC analog signal. The analog signal is transferred to the transmitter PCB and the RF circuit encodes the modulated analog signal onto the 5.8 Ghz carrier signal. The 5.8Ghz carrier signal is sent up the 50 ohm impedance antenna line to the antenna. The antenna is tuned to resonate at 5.8Ghz and the signal is transmitted into open space to be received by a compatible receiver.                     ! "#  $       %  "&#   $      %        $        &       ' $ $  $            (  $      )  *+! )         $   ,    %                              )    %        )  $   $ %           %$             -  %              . )                  %      $   )    %      $        $            ! ϋϋ            ϋϋ.          )      ϋϋ    )                     ϋϋ      '     /0       FCC ID: 2ABYQFSV1251

Shenzhen Fatshark Co., Ltd. 8th floor, Building D, Longjing industrial Zone, Bantian,Shenzhen, PRC. DATE: 2014-06-30 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: __ 2ABYQFSV1251 ____ Product Name:__ ULTRAMICRO FPV CAMERA_ Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description  Parts Lists These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this / Day of 6/30/2014 / By: Linda Signature Printed Title: Purchasing supervisor On behalf of : Shenzhen Fatshark Co., Ltd Telephone: 0755-28435505

Shenzhen Fatshark Co., Ltd. 8th floor, Building D, Longjing industrial Zone, Bantian,Shenzhen, PRC. DATE : 2014-06-30 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID:__ 2ABYQFSV1251 ____ Product Name: __ ULTRAMICRO FPV CAMERA _ Request for Short-Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device on July 14,2012 • Test Setup Photos • External Photos • Internal Photos • User Manual These documents contain detailed system and equipment description and related information about the product which Shenzhen Fatshark Co., Ltd. considers to be proprietary, confidential, and a custom design and, otherwise would not release to the general public. Since this design is a basis from which future technological products will evolve, Shenzhen Fatshark Co., Ltd. considers this information to be of benefit to its competitors, and that the disclosure of information in these documents would give competitors an unfair advantage in the market This request is being made retroactively due to an over site on our part. We understand that the information has been publicly available since the date of grant. Dated this / Day of 3/16/2014 / By: Linda Signature Printed Title: Purchasing supervisor On behalf of : Shenzhen Fatshark Co., Ltd Telephone: 0755-28435505

External Photos of EUT Sample

Label Location Label Material: Synthetic paper he hole of the label will be get through by the camera wire, at the end of the T wire there is a connector which is bigger than the hole of the label so that the label is attached to the product permanently.

Internal Photos of EUT Sample

RF Exposure evaluation According to KDB 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m So pt = (EXd) 2 /30 x gt Field strength (average value)= 92.39 dBuV/m @3m / 5800 MHz Ant gain = 0dBi; so Ant numeric gain=1 So pt={ [10 (92.39 /20) /10 6 x3] 2 /30x1 }x1000 mW = 0.52 mW So ( 0.52 mW/5mm)x √5.8 GHz = 0.25 <3 Then SAR evaluation is not required

Shenzhen EBO T echnology Co., Ltd . 1-4F, Huafeng Science Park, Xin’an Sixth Road, 82 th District, Bao’an, Shenzhen, China. Telephone: +86-755-29451282, Fax: +86-755-22639141 Report No.: FCC14-RTE062501 Page 1 of 18 Authorized Signature: Kevin Yu Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the EBO product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of EBO International Electrical Approvals or testing done by EBO International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by EBO International Electrical Approvals in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 FCC REPORT Applicant: SHENZHEN FATSHARK ELECTRONIC CO., LTD Address of Applicant: 8FL, Mansion D, Longjing Industry Zone, Bantian, Longgang District, Shenzhen Equipment Under Test (EUT) Product Name: ULTRAMICRO FPV CAMERA Model No.: 1251 FCC ID: 2ABYQFSV1251 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2013 Date of sample receipt: June 18, 2014 Date of Test: June 18, 2014 To June 25 2014 Date of report issued: June 25, 2014 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. day s only.” Shenzhen EBO Technology Co., Ltd . Report No.: FCC14-RTE062501 Page 2 of 25 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn 2 Version Version No. Date Description 00 June 25, 2014 Original Prepared By: Date: June 25, 2014 Project Engineer Check By: Date: June 25, 2014 Reviewer and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” Shenzhen EBO Technology Co., Ltd . Report No.: FCC14-RTE062501 Page 3 of 25 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE............................................................................................................................................ 1 2 VERSION..................................................................................................................................................2 3 CONTENTS..............................................................................................................................................3 4 TEST SUMMARY.....................................................................................................................................4 5 GENERAL INFORMATION...................................................................................................................... 5 5.1 CLIENT INFORMATION......................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT......................................................................................................... 5 5.3 TEST MODE..................................................................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS 1. Description: Radiated Emission Test Setup for 30MHz ~ 1GHz 2. Description: Radiated Emission Test Setup for 1GHz ~ 18GHz 3. Description: Radiated Emission Test Setup for 18GHz ~ 40GHz