2ABYQFSV2461FSTX5MW

www.fatshark.com Model 2461 (FCC compliant 5G8 TX, ID# 2ABYQFSV2461) Spec Doc REV A Operation: Power is supplied via the 2p power in connector. 5V is supplied to the camera via the 3p camera connector. When connected to a compatible camera, the camera image is transmitted via the transmitter and antenna. The channels can be selected the 4p DIP switch (see chart). An alternative 5p connector is provided for connecting sources that use the stereo audio channels. Specifications: Power supply 6 - 17V (2S-4S supply) Power consumption: 75mA @7.4V (+camera supply) Power out (to camera) 5V, 350mA max Transmitting range: Approximately 200m Operating Frequency: 5G8 (see above frequency chart) Antenna type: fixed circular polarized Dimensions: 39 (+44 antenna) X 26 X 14 mm Weight: 19g (with antenna, no cables) Connector Function (from left to right) 2p: V+ (6-17V), GND 3p: 5V, GND, VID 5p: 5V, GND, VID, AUDL, AUDR Packaging Dimensions: 120 x 40 x 18 mm Weight: 40g Note: 5p connector is for connecting cameras with audio or ImmersionRC TinyTelemetry accessory (adds Telemetry data to audio channel so plane can be tracked with the ImmersionRC antenna tracker for longer range) Model FSV2461 (FCC compliant 5G8 TX, ID# 2ABYQFSV2461) 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, 14 including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ϋϋ Reorient or relocate the receiving antenna. ϋϋ Increase the separation between the equipment and receiver. ϋϋ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ϋϋ Consult the dealer or an experienced radio/TV technician for help. including interference that may cause undesired operation.

Linda Lee

has been publicly available after 180 days since the date of grant. Linda Lee

External Photos of EUT Sample

Label Location

Internal Photos of EUT Sample

RF Exposure evaluation According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd)2/30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10((dBuV/m)/20)/106 d = measurement distance in meters (m)---3m So pt = (EXd)2/30 x gt Average Field strength = 93.88dBuV/m @3m Ant gain =3dBi; so Ant numeric gain= 1.995 So pt={ [10 (93.88 /20) /10 6 x3] 2 /30x1.995 }x1000 mW = 0.37 mW So ( 0.37 mW/5mm)x √5.86 = 0.18 <3 Then SAR evaluation is not required

Shenzhen EBO T echnology Co., Ltd . 1-4F, Huafeng Science Park, Xin’an Sixth Road, 82 th District, Bao’an, Shenzhen, China. Telephone: +86-755-29451282, Fax: +86-755-22639141 Report No.: FCC14-RTE031301 Page 1 of 25 Authorized Signature: Kevin Yu Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the EBO product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of EBO International Electrical Approvals or testing done by EBO International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by EBO International Electrical Approvals in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 FCC REPORT Applicant: Shenzhen Fatshark Co., Ltd Address of Applicant: 8 th floor, Building D, Longjing industrial Zone, Bantian, Shenzhen, PRC Equipment Under Test (EUT) Product Name: FSTX5MW Trade Mark: Fat shark Model No.: FSV2461 FCC ID: 2ABYQFSV2461 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2013 Date of sample receipt: March 3, 2014 Date of Test: March 3, 2014 To March 13, 2014 Date of report issued: March 13, 2014 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. day s only.” Shenzhen EBO Technology Co., Ltd . Report No.: FCC14-RTE031301 Page 2 of 25 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn 2 Version Version No. Date Description 00 March 13, 2014 Original Prepared By: Date: March 13, 2014 Project Engineer Check By: Date: March 13, 2014 Reviewer and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” Shenzhen EBO Technology Co., Ltd . Report No.: FCC14-RTE031301 Page 3 of 25 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.ebotek.cn and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.ebotek.cn . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE............................................................................................................................................ 1 2 VERSION..................................................................................................................................................2 3 CONTENTS..............................................................................................................................................3 4 TEST SUMMARY.....................................................................................................................................4 5 GENERAL INFORMATION...................................................................................................................... 5 5.1 CLIENT INFORMATION......................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT......................................................................................................... 5 5.3 TEST MODE................................................................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS 1. Description: Radiated Emission Test Setup for 30MHz ~ 1GHz 2. Description: Radiated Emission Test Setup for 1GHz ~ 18GHz