2AC37PBG-3030SBluetooth Speaker with LED Light

1 INSTRUCTION MANUAL Models: PBG-4040S，PBG-3535S,PBG-3030S,PBG-2020S,PBG-1515S Outdoor speakerlighting with Bluetooth Specification： （1）Adapter：Input 85-240AC Output 5V/2A （2） RGB LEDS （4）Working time：After full charge, Lighting could work 4-6H （3）Charging time：6-8H （4）Blue tooth name: Landaa （5）No need Password normally,But some mobile phone maybe need,the password is : 0000 （6）Blue tooth range 10M. receive range will be reduced as the battery voltage decrease. （7）Water resistance:IP44 CAUTION! - This is not a TOY. Keep it out of reach by children. - Keep this product away from chemical, any liquid, or heat - Do not sit on patio furniture if damage is found. - External adapter: Never use the external adapter for purpose other than battery charging for the light(s) supplied in the same pack. The external adapter, / socket on the light should not be used outdoor, not exposed to rain, humidity, any liquid, or heat. Keep the external adapter and charger station out of reach of children. Disconnect the external adapter from power when not in use. Never attempt to open the external adapter, charger station, or light bottom. - Keep remote control away from water, any liquid, or heat. Operation Charge the light—First step. WARNING! Never charge the product in a pool, water, or in rain. Charge in a dry, indoor location only. Insert the adaptor plug into the socket, Photo 1 Connect the external adapter to the electrical outlet. It will begin to charge and charging indicator light will be on red. Charging indicator light will be turn to green after full charged, Please cover the charge cap after fully charged. PDF created with pdfFactory Pro trial version www.pdffactory.com 2 Bluetooth light will keep the same working mode you are operating when charge in the case of electricity is not exhausted. Bluetooth light will flash when charge in the case of electricity is exhausted. Photo-1 The external adapter should not be used outdoor, not exposed to rain, humidity, any liquid, or heat. PHOTO1 Operation by Remote Control Photo-2 NOTE: First remove the small plastic sheet from the battery cover before below Charge hole and cap Charge indicator，charging indicator light will be on red. Charging indicator light will be turned to green after full charged PDF created with pdfFactory Pro trial version www.pdffactory.com 3 operation 1. Brightness intensity and speed button：Adjust the speed under smooth modes. Change brightness intensity when the light is fixed on one single color. 2. Light ON/OFF button: Press this button to power the light on and off. Power on is the first step for all functions on remote control. Once the color cube is power on, press ON/OFF button again is only to turn on or off the lighting, If the Bluetooth is connected, Press ON/OFF button does no has effect to Bluetooth. This color cube has memory storage function when electricity is not exhausted. The light could keep the same lighting working mode or color which you turned off last time. For example, last time you turned off the light on “RED” mode, this time you press the ON/OFF button, the mode will still be on “RED” mode. When electricity is used exhausted last time, there will be no memory storage function. After fully charged, you press the ON/OFF button, the initial mode is on “SMOOTH” mode. 3、 Press this button to turn on and turn off Bluetooth. after press the button, once the Bluetooth is on, The Bluetooth indicator light will start to flash in Blue color and a voice “power on “ come out , then use your mobile phone Bluetooth to match the “Landaa” Bluetooth, Once the Bluetooth is connected with your mobile phone, Bluetooth indicator light will be kept on blue color but not flash and a voice “Speaker connected “ come out , Photo-2; While connected, If you go away more than 10 Meters, The Bluetooth indicator light will return to flash in Blue color and a voice “speaker disconnected “ come out , your mobile phone will be disconnected with the speaker; If you go back to the speaker less than 10 Meters, Bluetooth indicator light will be kept on blue color but not flash and a voice “Speaker connected “ come out again and your Mobile phone will connected the speaker automatically; Bluetooth indicator light is inside the cube and could looks below the speaker ; Once the Bluetooth is connectted, Press the button again the Bluetooth will be off. The Bluetooth indicator light will be off once the Bluetooth is off (After Bluetooth is off and then press and power on the BlueTooth again, you must manual connect the speaker); One mobile phone only could match with one Bluetooth to play music at the same time. Photo-3 Bluetooth indicator light (Inside) PDF created with pdfFactory Pro trial version www.pdffactory.com 4 4、 Color selection button：When the light is on Press this button to choose your favorite color as shows on remote control (Six colors) 5 + White color warm increase button: When the light is on, Press this button to change the white color to more warm. Total 11 stages; 6 - White color warm decrease button: When the light is on, Press this button to change the white color to more cold. Total 11 stages; 7、 Color selection button：When the light is on, Press this button to choose your favorite colors (Total 7 colors) 8、 Music Flash Button: the light will flash with the music automatically. 9、 Smooth Button: 7colors scrolling automatically. 10、Time button: Once you power on the light, the counter down is not acted and it will work Continuously. If you press the time Button once, the counter down is acted and the light mode will be “Red” Mode, and it will work 30 minutes and then shut off the light and Bluetooth automatically after 30 minutes; If you press the time Button 2 times, the counter down is acted and the light mode will be “Green” Mode ,and it will work 60 minutes and then shut off the light and Bluetooth automatically after 60 minutes; If you press the time Button 3 times, the counter down is acted and the light mode will …

Text truncated - open the document above for the full version.

Power beauty (Dongguan) Industrial Co.,Ltd No. 1, Eastern Industry Park, Shujiu Village Changping Town,Dong Guan ,Guang Dong , China (Permanent or also called long term confidentiality is the normal method to keep certain docuements confidential, and may apply to schematics, block diagrams, operational description and bill of materials.) To: Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Pursuant to 47 CFR Section 0.459(a) & (b), we, (the applicant / grantee) Company name Power beauty (Dongguan) Industrial Co.,Ltd Address No. 1, Eastern Industry Park, Shujiu Village Changping Town,Dong Guan ,Guang Dong ,China City Dong Guan Country China request for this certification filing under: Grantee Code Product Number FCC ID: 2AC37 PBG-3030S to maintain permanent confidentiality for the following documents submitted within this application: (please cross what is applicable, or add other documents, provide the file name and description) Exhibit File Name Description Operational Description Operational Description explaining the functioning of the block diagram Block Diagrams Block Diagrams showing the systematic building blocks of the EUT Schematics Diagrams Schematics Diagrams showing components, their values and interconnection Bill of Materials N/A List of components used on the PCB’s of the EUT Internal View of EUT Internal View of EUT the Internal View of EUT External View of EUT External View of EUT the External View of EUT Above materials crossed contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. We understand that pursuant to 47 CFR section 0.457(d)(1)(ii) disclosure of the applicant and all accompanying documentation will not be made before the date of the grant. The documents indicated as confidential above, are not publicly available elsewhere. Attestation: City and Country: Date: Name: (this must be a person) Function: Signature: (or official company stamp) Dong Guan 2014-09-11 Johnson Xu manager PDF created with pdfFactory Pro trial version www.pdffactory.com

Power beauty (Dongguan) Industrial Co.,Ltd No. 1, Eastern Industry Park, Shujiu Village Changping Town,Dong Guan ,Guang Dong , China We, (the approval holder) Company name Power beauty (Dongguan) Industrial Co.,Ltd Address No. 1, Eastern Industry Park, Shujiu Village Changping Town,Dong Guan ,Guang Dong ,China City Dong Guan Country China declare that the following representative (agent): Name (person) Kelly jiang Company name Shenzhen ECT Testing Technology Co;Ltd Address Room 808,Era Innovation Certer ,Xixiang gushu second road,Baoan district,Shenz hen city,China City Shenzhen Country China is hereby authorized to apply the following equipment for certification on our behalf: Product Description Bluetooth speaker with led light Type or Model(s) PBG-3030S, PBG-1515S, PBG-2020S, PBG-3535S, PBG-4040S, PBG-6035S Tradename or Brand(s) N/A We also authorize Teleconformity (Mr. M. Koop, Manager Certification, Address: Rietven 31, 7534NH Enschede, the Netherlands) to apply and sign this application for certification, registration or filing on our behalf (as representative agent or certifier). Attestation: City and Country: Date: Name: (this must be a person) Function: Signature: (or official company stamp) Dong Guan 2014-09-11 Johnson Xu manager PDF created with pdfFactory Pro trial version www.pdffactory.com

Report No.: ECT2014E02098 Page 1 of 4 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China External View of EUT Model: PBG-3030S Photo 1 Model: PBG-3030S Photo 2 Report No.: ECT2014E02098 Page 2 of 4 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: PBG-3030S Photo 3 Model: PBG-3030S Photo 4 Report No.: ECT2014E02098 Page 3 of 4 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: PBG-3030S Photo 5 Model: PBG-3030S Photo 6 Report No.: ECT2014E02098 Page 4 of 4 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: PBG-3030S Photo 7

Label location

Label PDF created with pdfFactory Pro trial version www.pdffactory.com PDF created with pdfFactory Pro trial version www.pdffactory.com

Report No.: ECT2014E02098 Page 1 of 3 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Internal View of EUT Model: PBG-3030S Photo 1 Model: PBG-3030S Photo 2 PDF created with pdfFactory Pro trial version www.pdffactory.com Report No.: ECT2014E02098 Page 2 of 3 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: PBG-3030S Photo 3 Model: PBG-3030S Photo 4 PDF created with pdfFactory Pro trial version www.pdffactory.com Report No.: ECT2014E02098 Page 3 of 3 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Model: PBG-3030S Photo 5 Model: PBG-3030S Photo 6 PDF created with pdfFactory Pro trial version www.pdffactory.com

Report No.: ECT2014E02098 Page 1 of 1 Rev: None RF Exposure Compliance Requirement The product belongs to standalone portable device base the FCC rule part 2.1091&2.1093. The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. The Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: Transmit frequency (GHz) Max Conducted Output Power (mW) SAR Test Exclusion Threshold (mW) 2.402 1.132 9.7 2.441 1.923 9.6 2.480 2.158 9.5 The SAR Test Exclusion Threshold for 100 MHz to 6 GHz is calculated from: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v05r02, the SAR report is not required. PDF created with pdfFactory Pro trial version www.pdffactory.com

Report No.: ECT2014E02098 Page 1 of 58 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China FCC Test Report Part 15 subpart C Client Information: Applicant : Power beauty (Dongguan) Industrial Co.,Ltd Applicant add.: No. 1, Eastern Industry Park, Shujiu Village Changping Town,Dong Guan ,Guang Dong ,China EUT Information: EUT Name : Bluetooth speaker with led light Model No. : PBG-3030S, PBG-1515S, PBG-2020S, PBG-3535S, PBG-4040S, PBG-6035S Brand Name : N/A FCC ID : 2AC37PBG-3030S Prepared By: Shenzhen ECT Testing Technology Co., Ltd. Add. : No Room 808,Era Innovation Certer, Xixiang gushu second road, Baoan district, Shenzhen city, China Date of Receipt: Aug. 20, 2014 Date of Test: Aug. 21~ Aug. 31, 2014 Date of Issue: Aug. 31, 2014 Te s t R e s u l t : Pass Test procedure used: ANSI C63.4-2009 This device described above has been tested by Shenzhen ECT Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. *This test report must not be used by the client to claim product endorsement by any agency of the U.S. government. Reviewed by: Approved by: Nancy Xu kelly Jiang Report No.: ECT2014E02098 Page 2 of 58 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China 1 Contents Page COVER PAGE 1 CONTENTS ...........................................................................................................................................................2 2 TEST SUMMARY ..................................................................................................................................................4 2.1 COMPLIANCE WITH FCC PART 15 SUBPART C .....................................................................................................4 2.2 MEASUREMENT UNCERTAINTY............................................................................................................................4 3 GENERAL INFORMATION ...................................................................................................................................5 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................................................5 3.2 DESCRIPTION OF TEST CONDITIONS....................................................................................................................7 3.3 EUT PERIPHERAL LIST.......................................................................................................................................8 3.4 TEST PERIPHERAL LIST......................................................................................................................................8 4 EQUIPMENTS LIST FOR ALL TEST ITEMS .......................................................................................................9 5 TEST RESULT.....................................................................................................................................................10 5.1 ANTENNA REQUIREMENT..................................................................................................................................10 5.1.1 Standard requirement ............................................................................................................................10 5.1.2 EUT Antenna .........................................................................................................................................10 5.2 CONDUCTION EMISSIONS MEASUREMENT.........................................................................................................10 5.2.1 Applied procedures / Limit .....................................................................................................................10 5.2.2 Test procedure.......................................................................................................................................10 5.2.3 Test results ............................................................................................................................................10 5.3 RADIATED EMISSIONS MEASUREMENT..............................................................................................................10 5.3.1 Applied procedures / Limit .....................................................................................................................10 5.3.2 Test procedure.......................................................................................................................................10 5.3.3 Test Result .............................................................................................................................................10 5.3.4 TEST RESULTS (Restricted Bands Requirements)..............................................................................10 5.4 BANDWIDTH TEST.......................................................................................................................................10 5.4.1 Applied procedures / Limit .....................................................................................................................10 5.4.2 Test procedure.......................................................................................................................................10 5.4.3 Deviation from standard.........................................................................................................................10 5.4.4 Test setup ..............................................................................................................................................10 5.4.5 Test results ................................................................................................…

Text truncated - open the document above for the full version.

Report No.: ECT2014E02098 Page 1 of 2 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Test Setup Photograph Conducted Measurement Photos Report No.: ECT2014E02098 Page 2 of 2 Rev: None Shenzhen ECT Testing Technology Co., Ltd. No Room 808,Era Innovation Certer, Xixiang gushu second road,Baoan district, Shenzhen city, China Radiated Measurement Photos 30MHz-1GHz 1GHz-25GHz