2AC9N-136796Mighty Bluetooth Speaker

FCC Information FCC Radiation Exposure Statement This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. Instructions of use Slide the O/On switch on the speaker to the ON position. Press and hold the Bluetooth pairing button for 2 seconds. Tones will sound and the light will ash blue to indicate pairing attempt. Place your audio device in Bluetooth mode (look in the device’s settings menu) and make it discoverable. ‘Typo Mighty Speaker’ should appear on your device. If ‘Not Connected’, ‘Not Paired’ or similar message appears, select ‘Typo Mighty Speaker’ to connect. If prompted for a password, enter ‘1234’ on your device’s keypad. Once paired, the light will glow solid blue and a conrmation beep will sound and you can then stream audio. If pairing is not successful, turn the power o on the speaker and repeat the pairing procedure. To listen to Bluetooth audio in the future, slide the O/On switch on the speaker to the ON position. The light will ash blue slowly as the speaker attempts to auto-link with the last previously linked unit in range (30 feet). Control Bluetooth audio from your device. Remember to turn o the speaker and your device after listening. NOTE: When unit is charging, the blue light will appear solid red. Maintenance Place the unit on a level surface away from sources of direct sunlight or excessive heat. Protect your furniture when placing your unit on a natural wood and lacquered nish. A cloth or other protective material should be placed between it and the furniture. Clean your unit with a soft cloth moistened only with mild soap and water Do not use strong cleaning agents such as thinner or similar materials as they can damage the surface of the unit. NOTE: When not in use, turn speaker OFF to save battery power. Unit will automatically power down after 5 minutes if no audio or bluetooth stream is detected (you will then need to slide the power switch to OFF position. WARNING Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, re, or high temperature & not handled appropriately Do not place loose batteries in a pocket, purse, or other container containing metal objects, do not mix with used or other battery types, or store with hazardous or combustible materials. Store in a cool, dry, ventilated area. Follow applicable laws and regulations for transport and disposal. When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or re hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take note of following warnings; Charge before use – must be fully charged. Keep away from water, all liquids, moisture and heat. This product must be well ventilated at all times. This product should only be connected to a power supply as described in instructions. This product should only be cleaned as recommended. Keep unplugged from power source if not being used for a period of time. If damaged this can only be repaired by a professional technician. The speaker is powered by a rechargeable battery in the speaker. Make sure to charge the speaker before using. Connect the micro-USB plug to the USB Charging jack on the speaker. Connect the larger USB plug to USB AX adaptor or to a powered USB port, such as that on a computer. The light on the speaker will turn to solid red while charging and turn o when fully charged. When the red light ashes or if you start to notice sound distortion at higher volumes, it’s time to recharge the battery. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures; Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. TYPO MIGHTY SPEAKER Folded Booklet Each page is 70mm x 70mm FRONT BACK 210mm 70mm

RF_160, Issue 03 Declaration of Authorization We Name: Cotton On USA Inc Address: 16511, Trojan Way, La Miranda, California 90638, United States City: California Country: United States Declare that: Name Representative of agent: Tracy Qi Agent Company name: Shenzhen CTL Testing Technology Co., Ltd. Address: Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 City: Shenzhen Country: China is authorized to apply for Certification of the following product(s): Product description: Mighty Bluetooth Speaker Type designation: 136796 Trademark: / on our behalf. Date: July 28, 2015 City: California Name: Selwyn Prince Function: Compliance Manager Signature:

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: Cotton On USA Inc Address : 16511, Trojan Way, La Miranda, California 90638, United States City: California Country: United States To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2AC9N-136796 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: (notes 2, 3, 4, 5) Date: July 28, 2015 Name and signature of applicant: Selwyn Prince Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

FCC ID: 2AC9N‐136796

FCC ID: 2AC9N-136796 1. Reference According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, Where: f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison 2. Result 1) According to the output power measurement, and the tune-up statement by manufacturer, the calculated value can obtained. Test Frequency (MHz) Minimum Separation Distance (mm) Max. Output Power (dBm) Output Power with tune up (dBm) Output Power (mW) calculated value exclusion thresholds BT 2441.00 5.00 0.2881.01.260.40 3 2) .Conclusion: No SAR is required.

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-26636041 FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No.: CTL1507171986-WF Compiled by: ( position+printed name+signature) Jacky Chen (File administrators) Tested by: ( position+printed name+signature) Allen Wang (Test Engineer) Approved by: ( position+printed name+signature) Tracy Qi (Manager) Product Name..............................: Mighty Bluetooth Speaker Model/Type reference..................: 136796 List Model(s)................................: / Trade Mark....................................: / FCC ID...........................................: 2AC9N-136796 Applicant’s name....................: Cotton On USA Inc Address of applicant...................: 16511, Trojan Way, La Miranda, California 90638, United States Test Firm..................................: Shenzhen CTL Testing Technology Co., Ltd. Address of Test Firm...................: Floor 1- A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 Test specification........................: Standard........................................: FCC Part 15.247: Operation within the bands 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz. TRF Originator..........................: Shenzhen CTL Testing Technology Co., Ltd. Master TRF..............................: Dated 2011-01 Date of Receipt.............................: July 15, 2015 Date of Test Date..........................: July 16, 2015 –July 23, 2015 Data of Issue................................: July 24, 2015 Result............................................: Positive Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. V1.0 Page 2 of 41 Report No.: CTL1507171986-WF TEST REPORT Test Report No. : CTL1507171986-WF July, 24, 2015 Date of issue Equipment under Test : Mighty Bluetooth Speaker Model /Type : 136796 Listed Models : / Applicant : Cotton On USA Inc Address : 16511, Trojan Way, La Miranda, California 90638, United States Manufacturer : Cotton On USA Inc Address : 16511, Trojan Way, La Miranda, California 90638, United States Test result Pass * *In the configuration tested, the EUT complied with the standards specified page 5. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. V1.0 Page 3 of 41 Report No.: CTL1507171986-WF ** Modifited History ** Version Description Issued DataReport No. Remark Version 1.0 Initial Test Report Release2015-07-24 CTL1507171986-WF Tracy Qi V1.0 Page 4 of 41 Report No.: CTL1507171986-WF Table of Contents Page 1. SUMMARY............................................................................................................................................................ 5 1.1. TEST STANDARDS ..................................................................................................................................................... 5 1.2. TEST DESCRIPTION ........................................................................................................................................................ 5 1.3. TEST FACILITY .............................................................................................................................................................. 6 1.4. STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................................... 6 2. GENERAL INFORMATION ....................................................................................................................................... 7 2.1. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 7 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 7 2.3. DESCRIPTION OF TEST MODES AND TEST FREQUENCY .......................................................................................................... 7 2.4. EQUIPMENTS USED DURING THE TEST .............................................................................................................................. 8 2.5. RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................................................ 8 2.6. MODIFICATIONS ........................................................................................................................................................... 8 3. TEST CONDITIONS AND RESULTS ........................................................................................................................... 9 3.1. CONDUCTED EMISSIONS TEST ......................................................................................................................................... 9 3.2. RADIATED EMISSIONS AND BAND EDGE .......................................................................................................................... 12 3.3. MAXIMUM PEAK OUTPUT POWER ................................................................................................................................ 18 3.4. 20DB BANDWIDTH ..................................................................................................................................................... 19 3.5. FREQUENCY SEPARATION ....................................…

Text truncated - open the document above for the full version.