2ACHVMO-ST006MakeON Skin Light Therapy III

www. makeonbeauty.co.kr Product Name: Skin Light Therapy II Weight: 66g → 73g (based on design mock-up) Seller: Amore Pacific Co., Ltd. Manuf acturer: Amosense Co., Ltd. 100 Hangang-daero, Yongsan-gu, Seoul 90, 4sandan 5-gil, Jiksan- eup, Seobuk-gu, Cheonan-si, Chungcheongnam-doMADE IN KOREA Technology Energy that light of a specific wavelength transmits into the skinLIGHTActivation of skin energy + promotion of product absorptionMICRO CURRENT Make-up care for well-applied makeup 3min 3min Moisture supplementation care for dry skin Elasticity up care that keeps the skin firm 3min Hypoallergenic care optimized for sensitive skin 1 3min 1min 1min 1min Skin care device that cares from skin diagnosis to solution thr ough light and microcurrent Good to know before using! 2 1 Please recharge once after opening. Dry thoroughly with a towel and measure, do not apply skincare products for accurate results. Please select ‘Recommended Mode vs Selected Mode’. 2 3 Page 4 page Sweating or prolonged exposure to the sun may not produce the right results. ① Turn on the power.② Ready when the color of the button blinks③ A beep sounds at the center of the ball. Measurement is complete after a long time *Only the beep is repeated if the measurement is not successful. Wait until the sound stops without removing it from the measurement site. lack of moisture (Blink) In case of lack of oil (Blink In case of lack of elasticity Blink Measurement results After applying the cream, the sensor is placed on the face Automatically run the mode when touched Use Featured Mode (3 minutes ) ▷ Use after selecting a mode by pressing the button 측정모드 selection mode Featured Mode Product Introduction( Makeon Skin Light Therapy III A skin care device that provides a solution for skin change that is renewed by finding out the lack of skin 3 Touch sensor that recognizes skin A sensor that measures the condition of the skin on your face One button for easy use Long lasting use on a single charge  Works only when in contact with non-dry skin → Use after applying a sufficient amount of cream formulation.  If you measure the center of the ball for 3 seconds in the measurement mode, The most neces sary mode is automatically I f you want to use a mode other than t he recommended mode Press the button to change to the desired mode and use it.  Press the button once to proceed i n t he following order: mode is changed.  60 minutes of use with a full charge within 3 hours (can be used 20 times) • After opening, the power does not turn on because the battery is low. Pleaseuse it after charging. M E A S U RE M O I S T U RE S H I N E E L A S T I C I T Y S E N S I T I V E How to use 4 Select until you hearPress the button to turn on the power.. Point the device at the center of the cheek and hear a beep.wait until the end Check the required mode by the color of the side or button. moisture management Need for dead skin/gloss management Need to manage elasticity After sufficiently applying the product to enhance the effect, both cheeks (1 minute) ,Take care of the rest of the area, such as around the eyes, forehead (1 minute), around the mouth and neck 5 Result After 3 minutes of use, check the effect with the side LED. 1 Start 2 Measure 3 Check ※ Measurement results are visible only when used for 3 minutes in measurement mode 4 Care If the measurement is not performed properly, the alarm will co ntinue to sound, so please wait until the measurement is finished. enough carehas been done mode once moremode once more 4 PC 3PC How to use 5 select After the skin care step of toner and lotion, use after selecti ng the desired mode while applying enough cream to the face. Meas ure 2. I ntensive care for the area t o enhance the effect, and finis h with essence for moisturizing/soothing after use. START Skin care by part right after use Moisture content 98% corneo us Skin skin evenness skin clarity skin color 96%16% 9%3%1% eye wrinkles eye wrinkles skin elasticity face lifting skin density right after use 2% 25% 11% after 2 weeks of use 16% 14% 15% 2% 6% 10% moist ure shine elasti city sensi tive Can't you check the measurement result with the LED on the side after using the mode selection? Questions about use 모드 선택 사용 후 측정 결과가 옆면 LED로 확인이 안되나요? 6 Can the measurement mode be affected by the season? • Spring/Autumn: Due to dry weather, the frequency of moisture an d oil care is highly recommended. • Summer: Due to the intense heat, you sweat a lot, so firming care may be intensively recommended.. • Winter: Due to the cold and bitter wind, moisture and oil care are highly recommended. • After the normal measurement in the measurement mode and the us e of the automatically set mode is completed, the side LED You can se e how much better it is. (shows up to 4) Having a hard time checking if the use mode is working? • You can check which mode is active by checking the color of the button.. ((Example: LED color above the button → BLUE mode) • Use it so that it comes in contact with your skin, and if you f eel the light and vibration, you are using it correctly. • Safety was verified by conducting a skin safety evaluation test for skin irritation1 • If you feel uncomfortable with the stinging sensation, you can get a good e ffect when using it with a mask sheet attached. Questions about use • Completed certification of ‘photobiological safety test’ for ey es However, be careful not to look directly at the light for a long time.When using around the eyes, close your eyes to minimize glare. If you feel any discomfort around your eyes, such as eye fatigue, pain, foreign body sensation, etc., please stop using it temporarily. Do you feel a stinging sensation on your skin? Do you feel the light is too bright? Do you feel the light is too bright? 7 Precautions when using If you p ress it hard on your face, it may irritate your skin. Please ru b li g htly. • Do not use on areas with severe redness or swelling due to skin irritation duringuse. Please discontinu…

Text truncated - open the document above for the full version.

Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 20, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2ACHVMO-ST006 Amorepacific Corporation (“the applicant”) certifies that, as of the date of the filing of the application, AMOREPACIFIC US, INC is our designated U.S. agent for service of process for the above referenced FCC ID. Amorepacific Corporation accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. AMOREPACIFIC US, INC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Applicant Company name: Amorepacific Corporation Grantee FRN: 0023674070 Grantee Code: 2ACHV FCC ID: 2ACHVMO-ST006 Contact Name:Jinpyo Park Street Address: 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea City/Province/Zip: Seoul / Yongsan-gu / 04386 Telephone No: +82-2-542-0951 Email: [email protected] Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Designated U.S. Agent Information: Name: AMOREPACIFIC US, INC FRN number : 0034052704 Address: 1385 Broadway New York NEW YORK(10018) Contact Person: Ha-Young Jeon Tel.: 917 881 7289 Email: [email protected] Sincerely, Amore Pacific Co., Ltd AMOREPACIFIC US, INC Manager / Jinpyo Park Ha-Young Jeon (Applicant signature) (Applicant signature)

Rev 1/26/2023 Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 21, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2ACHVMO-ST006 Amorepacific Corporation (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Manager / Jinpyo Park Amorepacific Corporation Rev 1/26/2023 Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 21, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2ACHVMO-ST006 Amorepacific Corporation (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Manager / Jinpyo Park Amorepacific Corporation

Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Date: September 20, 2023 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID : 2ACHVMO-ST006 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules and IC regulation, we hereby request confidential treatment of information accompanying this application as outlined below: PERMANENT Exhibit Type File Name Part List Part List.pdf Schematics Diagram(s) Schematic.pdf Operation description Operation description.pdf Block diagram Block diagram.pdf And the above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Manager / Jinpyo Park Amore Pacific Co., Ltd

Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Date: September 20, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 FCC ID : 2ACHVMO-ST006 To whom it may concern: I, the undersigned, hereby authorize Young-Jin, Lee of KES Co., Ltd. and hereafter referred to as KES Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Young-Jin, Lee of KES Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KES Co., Ltd. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Manager / Jinpyo Park Amorepacific Corporation REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

Model No.: MO-ST006 Page 1 of 2 External photos Model No.: MO-ST006 Page 2 of 2 BLANK BLANK BLANK BLANK BLANK

Model No.: MO-ST006 Page 1 of 1 Label photo

Model No.: MO-ST006 Page 1 of 2 Internal photos Chip Antenna Model No.: MO-ST006 Page 2 of 2

Model No.: MO-ST006 Page 1 of 1 RF exposure FCC ID : 2ACHVMO-ST006 According to 447498 D01 General RF Exposure Guidance v06 The 1-g and 10-g SAR test exclusion thresholds for 100 ㎒ to 6 ㎓ at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ꞏ[√f(㎓)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, Where; f(㎓) is the RF channel transmit frequency in ㎓ Power and distance are rounded to the nearest ㎽ and mm before calculation The result is rounded to one decimal place for comparison Results Mode Frequency (㎓) Distance (mm) Max tune-up power (㏈m) Calculation value Exclusion Threshold (㏈m) (㎽) BLE 1 Mbps 2 402 5 1.00 1.26 0.39 ≤3.0 2 442 1.00 1.26 0.39 2 480 1.00 1.26 0.40

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (24) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) Mode: BLE_1 Mbps Channel 20 Distance of measurement: 3 meter - Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 001.30 47.50 Peak H -9.59 - 37.91 74.00 36.09 1 396.26 50.51 Peak V -6.88 - 43.63 74.00 30.37 1 595.24 52.94 Peak V -5.28 - 47.66 74.00 26.34 1 792.62 47.81 Peak V -3.39 - 44.42 74.00 29.58 4 883.10 48.19 Peak H 7.09 - 55.28 74.00 18.72 4 883.10 44.95 Peak V 7.09 - 52.04 74.00 21.96 4 884.60 34.51 Average H 7.10 1.76 43.37 54.00 10.63 시 점 확 인 필 정 부 시 점 확 인 센 터 진본 2023-08-30 14:59:28 KST KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (25) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) Horizontal // Peak for 1 ㎓ to 3 ㎓ Vertical // Peak for 1 ㎓ to 3 ㎓ Horizontal // Peak for 3 ㎓ to 18 ㎓ Vertical // Peak for 3 ㎓ to 18 ㎓ Horizontal // Average for 3 ㎓ to 18 ㎓ Vertical // Average for 3 ㎓ to 18 ㎓ N/A Note. 1. Average test would be performed if the peak result were greater than the average limit. KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (26) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) Mode: BLE_1 Mbps Channel 39 Distance of measurement: 3 meter - Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1199.68 49.14 Peak H -8.21 - 40.93 74.00 33.07 1393.26 48.17 Peak H -6.90 - 41.27 74.00 32.73 1396.86 52.24 Peak V -6.87 - 45.37 74.00 28.63 1597.84 52.47 Peak V -5.25 - 47.22 74.00 26.78 1797.22 48.31 Peak V -3.35 - 44.96 74.00 29.04 4961.10 49.53 Peak H 7.65 - 57.18 74.00 16.82 4961.10 46.26 Peak V 7.65 - 53.91 74.00 20.09 4961.10 37.83 Average H 7.65 1.76 47.24 54.00 6.76 - Band edge Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 2491.76 47.94 Peak V -0.56 - 47.38 74.00 26.62 2492.41 45.84 Peak H -0.56 - 45.28 74.00 28.72 Restricted band // Horizontal // Peak Restricted band // Vertical // Peak KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (27) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) Horizontal // Peak for 1 ㎓ to 3 ㎓ Vertical // Peak for 1 ㎓ to 3 ㎓ Horizontal // Peak for 3 ㎓ to 18 ㎓ Vrtical // Peak for 3 ㎓ to 18 ㎓ Horizontal // Average for 3 ㎓ to 18 ㎓ Vertical // Average for 3 ㎓ to 18 ㎓ N/A Note. 1. Average test would be performed if the peak result were greater than the average limit. KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (28) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) Test results (18 ㎓ to 30 ㎓) Mode: BLE_1 Mbps Channel: 00 (Worst case) Distance of easurement : 3 meter Horizontal Peak Vertical Peak Note. No spurious emission were detected above 18 ㎓. KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (29) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) 3.5 Conducted spurious emissions & band edge Test setup EUT Attenuator Spectrum analyzer Test procedure Band edge ANSI C63.10 – Section 11.11 1. Start and stop frequency were set such that the band edge would be placed in the center of the plot 2. Span was set large enough so as to capture all out of band emissions near the band edge 3. RBW = 100 ㎑ 4. VBW = 300 ㎑ 5. Detector = Peak 6. Trace mode = max hold 7. Sweep time = auto 8. The trace was allowed to stabilize Out of band emissions ANSI C63.10 – Section 11.11 1. Start frequency was set to 30 ㎒ and stop frequency was set to 25 ㎓ for 2.4 ㎓ frequencies and 40 ㎓ for 5 ㎓ frequencies 2. RBW = 100 ㎑ 3. VBW = 300 ㎑ 4. Detector = Peak 5. Trace mode = max hold 6. Sweep time = auto couple 7. The trace was allowed to stabilize Limit According to 15.247(d), in any 100 ㎑ bandwidth outside the …

Text truncated - open the document above for the full version.

Application Bluetooth Zigbee WLAN (IEEE 802.11 b/g) ISM 2.4GHz Wireless Devices Features PIFA Structure Small Size (3.0*1.5*1.2mm 3 ) Easy Optimizing with external lumped matching components SMT Available under Pb-free Condition RoHSCompliant DATASHEET DocumentDatasheet TypeDielectricChip Antenna Application2.4GHz Part No.AMAN301512ST01 Revision3.2 Notes The contents of this datasheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. AMOTECH Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 2 Rev. NoDateTitleContentsPage 0 08.09.30Newpublished 1 09.03.24Data Added Efficiencydata8 Changed carrier tapewidth (W16mm W12mm)12 1.109.04.07FormatChanged document format 1.214.08.06Correctedthe miswritten values3 214.09.26DataChangedAntenna Specification & Parameter3,5,6 2.115.08.01DataAdded Peak gain3, 6 2.215.12.23DataAdded Cautions (Recommendations)7 3.017.03.03DataChangedAntenna Specification & Parameter, PCB Design Guide3,4,5,6 3.118.06.01DataChanged Mechanical Specification (Operating Temperature)3 3.218.09.03DataReliability Test Condition for AEC-Q2007 Table of Content Revision History 1.Specifications 3 1.1 Electrical Specifications 3 1.2 Mechanical Specifications 3 1.3 Appearance and Material 3 2. PCB Design for Test 4 2.1 Evaluation BoardDimension 4 2.2 PCB Design Guide 4 3. Measurement Result 5 3.1 Typical Measurement Result (VSWR/RL,Smithchart) 5 3.2 Typical Measurement Result(Gain, Radiation Pattern) 6 4. Reliability 7 5. Cautions (Recommendations)7 6. Soldering Reflow Profile 7 7. Packaging 8 7.1 Carrier Tape Dimension 8 7.2 PackagingQuantity 8 7.3 Packaging Label 8 Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 3 NoItemSpec.Remark 1Frequency Range [MHz]2400 ~ 2485 2VSWRMax 3.0:1 3Avg. Gain [dBi] Typical-2.2 4Peak Gain[dBi] Max 3.3 5Efficiency [%]Min 63 6PolarizationLinear 7Impedance [Ω]Nominal 50 The results are measured on the 50x50mm 2 evaluation board(EVB). See Page 6. for more detail gain parameter NoItemSpec.Remark 1Dimensions (L*W*H)3.0*1.5*1.2 mm 3 2Unit WeightTypical 20 mg 3Operating Temperature-40 ~ +105 °C 1.1 Electrical Specifications 1.2 Mechanical Specifications NoItemFunctionMaterial ① Marking Feeding Index Ink ② MarkingWeek numberInk ③ ElectrodeRadiation ElementAg ④ Ceramic Body - Ceramic 1.3 Appearance & Material 1. Specifications ② ③ ① ④ [unit : mm] Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 4 2.1 Evaluation Board Dimension 2.2 PCB Design Guide 2. PCB Design for Test ② ③ ① NoPin Assignment ① Feeding ②GND ③ GND Matching Component 50 Ohm Feeding Line [unit : mm] Evaluation board size : 50*50 Fill Cut Area (GND Clearance) : 7.5*4.5 [PCB Solder Land] [unit : mm] Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 5 3.1 Typical Measurement Result (VSWR/RL, Smithchart) 3. Measurement Result The results are measured on the 50x50mm 2 evaluation board(EVB). ② ③ ① NoMatching Value ①100 pF ②4.7 pF ③ 2.7nH Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 6 [Eleviation1 plane @2.442GHz ] [Elevation2 plane @2.442GHz ] [Azimuth plane @2.442GHz ] [3D Radiation Pattern] Freq. [MHz] Efficiency (%) Avg. Gain (dBi) Peak Gain (dBi) 2400 74.2-1.32.6 2442 75.3-1.23.3 2485 63.9-2.03.0 3.2 Typical Measurement Result (Gain, Radiation Pattern) Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 7 NoItemTest ConditionTest Requirements 1 Adhesive Strength of Termination 1.Applied force on SMT chip till detached point from PCB. 1. No mechanical damage by applied force 2. Strength (F) > 3 kgf 2 Thermal Shock (Cycle) 1. Step 1 : -40 ±3°C, 30 min Step 2 : +125 ±3°C, 30 min 2. Number of cycle : 30 1. No visual damage 2. Within electric spec (VSWR) 3 High Temperature Resistance 1. Temperature : +125 ±5°C 2. Time : 1000 ±24 hrs 1. No visual damage 2. Within electric spec (VSWR) 4 Humidity 1. Humidity : 85 % RH Temperature : +85 ±3°C 2. Time : 1000 ±24 hrs 1. No visual damage 2. Within electric spec (VSWR) F SMD PAD PCB 4. Reliability 6. Soldering Reflow Profile 5. Cautions (Recommendations ) Storage environment of parts must be at ambient temperatures of 5 to 40°C and maximum 60%RH humidity The parts should be used within 6 months from the time of delivery. If stored for over 6 months, check for solder ability before use. Detail of AEC-Q200 measurement data would be available for request. Datasheet / Dielectric Chip Antenna / 2.4GHz AMAN301512ST01 (Rev 3.2) 8 ItemSpec.ItemSpec.ItemSpec. A01.80 ±0.10P04.00 ±0.10E1.75 ±0.10 B03.30 ±0.10P14.00 ±0.10F5.50 ±0.10 K01.35 ±0.10P22.00 ±0.10W12.00 ±0.30 D01.55 ±0.05--t0.30 ±0.05 Item QuantityDimension Reel2,500eaΦ7” * 12mm Inner Box7,500 ea (3 reel)185 * 185 * 68 (mm 3 ) Outer Box137,500 ea (5 Inner Box)365 * 200 * 200 (mm 3 ) Outer Box2105,000 ea (14 Inner Box)390 * 390 * 280 (mm 3 ) 7.1 Carrier Tape Dimension 7.2 Packaging Quantity 7.3 Packaging Label 7. Packaging AMOTECH Co., Ltd. 5BL-1Lot, 617, Namchon-Dong, Namdong-Gu, Incheon, Korea Dielectric Chip Antenna P/N : AMAN301512ST01 Lot No : Quantity : 2,500 pcs Date : 2009/04/09 ▲▲

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (1) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) TEST REPORT FCC Part 15.247 Equipment under test MmakeON Skin Light Therapy III Model name MO-ST006 FCC ID 2ACHVMO-ST006 Applicant Amorepacific Corporation Manufacturer AMOSENSE Co., Ltd. Date of test(s) 2023.07.17 ~ 2023.08.10 Date of issue 2023.08.29 Issued to Amorepacific Corporation 100, Hangang-daero, Yongsan-gu, Seoul, Republic of Korea Tel: +82-2-542-0951, Fax: +82-2-517-7183 Issued by KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea 473-21, Gayeo-ro, Yeoju-si, Gyeonggi-do, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 This test report is not related to KS Q ISO/IEC 17025 and KOLAS. Test and report completed by : Report approval by : Do-won, Ahn Test engineer Young-Jin Lee Technical manager 시 점 확 인 필 정 부 시 점 확 인 센 터 진본 2023-08-30 14:59:14 KST KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (2) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) Revision history Revision Date of issue Test report No. Description - 2023.08.29 KES-RF-23T0113 Initial KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-23T0113 Page (3) of (36) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP16-F01(00-23-01-01) TABLE OF CONTENTS 1. General information ..................................................................................................... 4 1.1. EUT description.............................................................................................. 4 1.2. Test configuration ............................................................................................ 5 1.3. Derivative Model Information............................................................................... 5 1.4. Accessory information ....................................................................................... 5 1.5. Sample calculation ........................................................................................... 5 1.6. Measurement Uncertainty ................................................................................... 5 1.7. Frequency/channel operations ............................................................................... 6 2. Summary of tests ........................................................................................................ 6 3. Test results ............................................................................................................ 7 3.1. 6 ㏈ bandwidth ............................................................................................. 7 3.2. Output power ................................................................................................ 9 3.3. Power spectral density ..................................................................................... 11 3.4. Radiated restricted band and emissions ................................................................... 13 3.5 Conducted spurious emissions & band edge .............................................................. 29 3.6. AC conducted emissions .................................................................................. 33 3.7. Antenna requirement ..............................................................................…

Text truncated - open the document above for the full version.