2ACSVHF-LPT271Wi-Fi+BLE Module

HF-LP271 Wi-Fi&BLE Module User Manual HF-LPT271 Low Power Wi-Fi +BLE Module User Manual V1.4 Overview of Characteristic Support Wi-Fi IEEE 802.11b/g/n and BLE 5.0 Wireless Standards  Based on RISC SOC, 160MHz CPU, 276KB RAM,2MB Flash  Support UART Data Communication with Wi-Fi or BLE  Support Wi-Fi STA/AP Mode  Support BLE Smart BLE Link Config  Support Wi-Fi AP Smart AP Linkand Sniffer Smart Link V8 Config Support Wi reless and Remote Firmware Upgrade Function Support Software SDK for Develop  PCB antenna only supported HF-LPT271 ：Internal PCB  Single +3.3V Power Supply for HF-LPT271 Si ze: HF-LPT271 ：24mmx 16mmx 3 mm, SMT16 package Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)- 1 - TABLE OF CONTENTS LIST OF FIGURES ................................................................................................................................... 3 LIST OF TABLES .................................................................................................................................... 4 HISTORY .................................................................................................................................................. 5 1.PRODUCT OVERVIEW ................................................................................................................ 6 1.1. General Description ................................................................................................................. 6 1.1.1 Key Application ................................................................................................................... 7 1.1.2 Device Paremeters ............................................................................................................. 7 1.2. Hardware Introduction ............................................................................................................. 8 1.2.1. HF-LPT271 Pins Definition ................................................................................................. 9 1.2.2. Electrical Characteristics .................................................................................................. 11 1.2.3. HF-LPT271 Mechanical Size ............................................................................................ 12 1.2.4. On-board Chip Antenna .................................................................................................... 13 1.2.5. Evaluation Kit .................................................................................................................... 13 1.2.6. Order Information .............................................................................................................. 15 APPENDIX D: CONTACT INFORMATION ...................................................................................... 16 Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)- 2 - OEM/Integrators Installation Manual..................................................................................................17 LIST OF FIGURES Figure 1. Block Diagram ........................................................................................................................ 6 Figure 2. HF-LPT271 Appearance ........................................................................................................ 8 Figure 3. HF-LPT271 Pins Map ............................................................................................................. 9 Figure 4. HF-LPT271 Mechanical Dimension...................................................................................... 12 Figure 5. Suggested Module Placement Region ................................................................................. 13 Figure 6. HF-LP271 EVK Type One .................................................................................................... 14 Figure 7. HF-LP271 EVK Type Two .................................................................................................... 14 Figure 8. HF-LPT271 Order Information .............................................................................................. 15 Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)- 3 - LIST OF TABLES Table1. HF-LPT271 Module Technical Specifications ........................................................................ 7 Table2. HF-LPT271 Pins Definition ..................................................................................................... 9 Table3. Absolute Maximum Ratings: ................................................................................................. 11 Table4. Evaluation Kit Interface Description ..................................................................................... 14 Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)- 4 - HISTORY Ed.V1.006-09-2020 FirstVersion. Ed.V1.106-10-2020 Updatesomeerror description Ed.V1.207-16-2020 Update 1MB and 2MB software difference. Ed.V1.409-16-2020 Delete 1MB version, and Add HF-LPT271 type. Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)- 5 - 1. PRODUCT OVERVIEW 1.1. General Description The HF-LPT271module is a fully self-contained small form-factor, single stream, 802.11b/g/n Wi-Fi +BLE module, which provide a wireless interface to any equipment with a Serial interface for data transfer.This module integrate MAC, baseband processor, RF transceiver with power amplifier in hardware and all Wi-Fi protocol and configuration functionality and networking stack, in embedded firmwar e to make a fully self-contained 802.11b/g/n Wi-Fi and BLE solution for a variety of applications. The HF-LPT271 moduleemploys the world's lowest power consumption embedded architecture. It hasbeen optimized for all kinds of client applications in the home automation, smart grid, handheld device, personal medical application and industrial control that have lower data rates, andtransmit or receive data on an infrequen…

Text truncated - open the document above for the full version.

QA-FR-170-B Company: High-Flying Electronics Technology Co., Ltd. Add: Room 1002, Building 1, No.3000, Longdong Avenue, Pudong New Area, Shanghai, 201203 China Tel: 400-189-3108 Fax: 021-31291158-8089 FCC Authorization Date: 2020-11-23 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 74 35 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, High-Flying Electronics Technology Co., Ltd., the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. o n our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Secti on 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Typed or Printed Name: Sen Xie Title: General Manager

Company: High-Flying Electronics Technology Co., Ltd. Add: Room 1002, Building 1, No.3000, Longdong Avenue, Pudong New Area, Shanghai, 201203 China Tel: 400-189-3108 Fax: 021-31291158-8089 E-mail: [email protected] FCC Confidential Authorization Date:2020-11-23 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 74 35 Oakland Mills Road Columbia, MD 21 046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2ACSVHF-LPT271 To: whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commission’s Ru les, High-Flying Electronics Technology Co., Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Typed or Printed Name: Sen Xie Title: General Manager

Applicant High-Flying Electronics Technology Co., Ltd. FCC ID: 2ACSVHF-LPT271 Section 15.212 Modular Transmitters Request for Modular Approval  Request for Limited Modular Approval   RequirementsEUT ConditionsComply(Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Refer to external photos. This module does have shield cover. Y 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over‐modulation. All inputs to the modules are buffered through logic or microprocessor inputs. Refer to Schematics. Y 3 The modular transmitter must have its own power supply regulation. The Module uses the chip BL602C20 with built-in power management components, the module rated power is 3.3V power, Refer to schematics. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of §§15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of §15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter has a PCB antenna arrangement for 2.4G WiFi&BLE, Refer to internal photo. Y Company: High-Flying Electronics Technology Co., Ltd. Add: Room 1002, Building 1, No.3000, Longdong Avenue, Pudong New Area, Shanghai, 201203 China Tel: 400-189-3108 Fax: 021-31291158-8089 E-mail: [email protected] 5 The modular transmitter must be tested in a stand‐alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of th ese lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and co mmercially available (see §15.31(i)). The modular transmitter is connected to the controlled board when testing. Please refer to setup photo. Y 6 If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:“ContainsTransmitter Module FCC ID: 2ACSVHF-LPT271” Any similar wording that expresses t he same meaning may be used. The Grantee ma y eit her provide such a label, an example of which must be included Refer to the label. Y in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Refer to manual Y 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Y Sincerely Yours, Sig nature: Typed or Printed Name: Sen Xie Title: General Manager The EUT comply with RF exposure requireme nts § 2.1091.If the device built into a host as a portable usage, the RF exposure evaluation may be required as specifie d by § 2.1093.

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS

Wi‐Fi+BLE Module HF-LPT271 FCC ID: 2ACSVHF-LPT271

EXHIBIT B - EUT INTERNAL PHOTOGRAPHS 2.4G Wi-Fi/BLE Antenna

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHD201123001-00A FCC Part 15.247 Page 14 of 73 FCC §15.247 (I) & §1.1310 & §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart 15.247 (i) and subpart 1.1310, 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f²) 30 30-300 27.5 0.073 0.2 30 300-1500 / f/1500 30 1500-100,000 / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density Calculated Formulary: Predication of MPE limit at a given distance S = PG/4πR² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); Calculated Data: Mode Frequency Range (MHz) Maximum Antenna Gain Tune-up Conducted Power Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric) (dBm) (mW) 802.11b 2412-2462 2.00 1.58 26.00 398.11 20 0.1251 1.0 802.11g 2.00 1.58 24.50 281.84 20 0.0886 1.0 802.11n- HT20 2.00 1.58 24.50 281.84 20 0.0886 1.0 BLE 2402-2480 2.00 1.58 17.00 50.12 20 0.0158 1.0 Note: Wi-Fi and BLE can't transmit simultaneously. Conclusion: The EUT meets exemption requirement- RF exposure evaluation greater than 20cm distance specified in § 2.1091. If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by§ 2.1093.

FCC PART 15.247 TEST REPORT For High-Flying Electronics Technology Co., Ltd. Room 1002, Building 1, No.3000, Longdong Avenue, Pudong New Area, Shanghai, 201203 China FCC ID: 2ACSVHF-LPT271 Report Type: Original Report Product Type: Wi-Fi+BLE Module Project Engineer: Jack Jiao Re port Number: RSHD201123001-00A Re port Date: 2021-01-04 Reviewed B y: Oscar Ye EMC Manager Prepared By: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road, Kunshan, Jiangsu province, China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHD201123001-00A FCC Part 15.247 Page 2 of 73 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 9 EXTERNAL I/O CABLE ................................................................................................................................................ 10 BLOCK DIAGRAM OF TEST SETUP .............................................................................................................................. 10 SUMMARY OF TEST RESULTS ............................................................................................................................. 12 TEST EQUIPMENT LIST ......................................................................................................................................... 13 FCC §15.247 (I) & §1.1310 & §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE (MPE) .................................. 14 APPLICABLE STANDARD ............................................................................................................................................ 14 CALCULATED FORMULARY: ....................................................................................................................................... 14 CALCULATED DATA: .................................................................................................................................................. 14 FCC §15.203 - ANTENNA REQUIREMENT ........................................................................................................... 15 APPLICABLE STANDARD ............................................................................................................................................ 15 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 15 FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS ..................................................................................... 16 APPLICABLE STANDARD ............................................................................................................................................ 16 EUT SETUP ................................................................................................................................................................ 16 EMI TEST RECEIVER SETUP ....................................................................................................................................... 16 TEST PROCEDURE ...................................................................................................................................................... 17 FACTOR & OVER LIMIT CALCULATION ...................................................................................................................... 17 TEST RESULTS SUMMARY .......................................................................................................................................... 17 TEST DATA ................................................................................................................................................................ 17 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS ............................................................................. 22 APPLICABLE STANDARD ............................................................................................................................................ 22 EUT SETUP ................................................................................................................................................................ 22 EMI TEST RECEIVER SETUP ....................................................................…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS Conducted Emissions (Front View) Conducted Emissions (Side View) RadiatedEmissions (Below 1GHz) RadiatedEmissions (Above 1GHz)