2AD8Q-SHSB2.4G Wireless Remote Controller

2.4G Wireless Remote Controller User Manual 1. Use description （1）Battery installation Unfastening the rear cover screw and remove it, install two NO.7 batteries. Be sure the correction of polarity of battery. The flash of the SPEED_INDICATOR & CAR_SELECT_INDICATOR will show it . （2）The CAR_SELECT key & CAR_SELECT_INDICATOR Use this key to ensure the unique correct corresponding of the remote to this car. Press the CAR_SELECT key for more then 2 to 3 seconds, the CAR_SELECT_INDICATOR will turn off, it shows that the remote can control this car .It can only control this car, and not defect others. Note: Be Sure the power of the car is on, and the Closer between the transmitter and the car. （3）STOP key The car will be stopped moving immediately as soon as this button is pressed in both remote and manual operator mode. （4）The SPEED_SLECT key & SPEED_SELECT indicator This button is used to select the speed grade of the car. The grade will change in the range of 3-level: low[one SPEED_INDICATOR flush ]、medium[two SPEED_INDICATOR flush] and high[three SPEED_INDICATOR flush] speed. The change of the order is LOW-MEDIUM-HIGH-MEDIUM-LOW as the button pressed. Note: Only the forward direction moving can own this function, , the back word not 5 FORWARD_KEY & BACKWORD_KEY Used to control the moving . Press one of the buttons, the car speed will ascend slowly to the setup speed grade. So the child in this car won't have the sudden shock and feel comfortable. （6）LEFT_LEY & RIGHT_LEY Used to control the left and right direction of the car. Receiver: 3. Notice （1）The transmitter owns energy-saving function. The power will automatic turn off as the remoter is idle for about 10 seconds . it will work as any of the button is pressed. （2）The CAR_SELECT Key must be operator once in the first time use of the remoter and replace the remoter batteries. （3）The performance of the remote will be affected with damp, wet. So keep it off . （4）The transmitter is only for adult use This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Add: No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Tel: +86-021 57339193 Fax: +86-021 57333688 Date: 2015-02-12 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA FCC ID: 2AD8Q-SHSB Dear Sir/Madam, We, SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Hereby declares the following statement for SIEMIC, INC, PCB board, circuit, structure and internal of these model(s) are the same, Only color and model number is different for these model: Product name: 2.4G Wireless Remote Controller Model no.: SHSB12VJD-3S,SHSB12VHH-9S,SHSB12VHH-3S,SHSB12VPJ-3S,SHSB6VJD-XS, SHSB12VHH-2S,SHSB6VPJ-2S Sincerely, Client’s name / title : Kang Sen / General Manager Contact information / address : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Tel: +86-021 57339193 Fax: +86-021 57333688 E-Mail: [email protected]

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Add: No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Tel: +86-021 57339193 Fax: +86-021 57333688 2015-02-11 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA FCC ID: 2AD8Q-SHSB Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (Product description, model name): 2.4G Wireless Remote Controller , SHSB12VJD -3S,SHSB12VHH-9S,SHSB12VHH-3S, SHSB12VPJ -XS,SHSB12VHH-2S,SHSB6VPJ-2S Sincerely, Client’s name / title : Kang Sen / General Manager Contact information / address : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Tel: +86-021 57339193 Fax: +86-021 57333688 E-Mail: [email protected] -3S SHSB6VJD

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Add: No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Tel: +86-021 57339193 Fax: +86-021 57333688 2015-02-11 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AD8Q-SHSB We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Kang Sen / General Manager Contact information / address : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Tel: +86-021 57339193 Fax: +86-021 57333688 E-Mail: [email protected]

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 4 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 4 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 4 Fig.5 Fig.6 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 4 Fig.7

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Product Name: 2.4G Wireless Remote Controller Model No.: SHSB12VJD-3S FCC ID: 2AD8Q-SHSB This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made In China Size:L:4cm*W:3cm Label location

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 21 FCC TEST REPORT FOR SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD 2.4G Wireless Remote Controller Model No.: SHSB12VJD-3S Additional Model No.: SHSB12VHH-9S,SHSB12VHH-3S, SHSB12VPJ-3S,SHSB6VJD-XS,SHSB12VHH-2S,SHSB6VPJ-2S Prepared for : SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Address : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Date of receipt of test sample : February 03, 2015 Number of tested samples : 1 Serial number : Prototype Date of Test : February 03, 2015 - February 11, 2015 Date of Report : February 11, 2015 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 21 FCC TEST REPORT FCC CFR 47 PART 15 C(15.249): 2014 Report Reference No. ............... : LCS1501271062E Date of Issue ................................. : February 11, 2015 Testing Laboratory Name ............. : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ......................................... : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure ......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Address ......................................... : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Test Specification Standard ........................................ : FCC CFR 47 PART 15 C(15.249): 2014 Test Report Form No. ................... : LCSEMC-1.0 TRF Originator ............................. : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ................ : 2.4G Wireless Remote Controller Trade Mark ................................... : SB Model/ Type reference.................. : SHSB12VJD-3S Ratings .......................................... : DC 3.0V by 2*AAA batteries Result ......................................... : Positive Compiled by: Supervised by: Approved by: Dick Su/ File administrators Danny Huang/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 21 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1501271062E February 11, 2015 Date of issue Type / Model........................... : SHSB12VJD-3S EUT......................................... : 2.4G Wireless Remote Controller Applicant............................... : SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD Address.................................. : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD. Address................................... : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Telephone............................... : / Fax.......................................... : / Factory................................... : SHANGHAI SENBO MACHINE MANUFACTURE CO., LTD. Address................................... : No.2005 Wanlian, Wanfeng Highway, Zhujing Town, Jinshang District, Shanghai, China Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 21 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................... 5 1.1. Description of Device (EUT) ................................................................................................................. 5 1.2. Host System Configuration List and Details .......................................................................................... 5 1.3. External I/O ............................................................................................................................................ 5 1.4. Description of Test Facility.................................................................................................................... 6 1.5. Statement of the measurement uncertainty ............................................................................................ 6 1.6. Measuremen…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD8Q-SHSB Report No.: LCS1501271062E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 1 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement (X Position) Fig.1 Fig.2