2ADGKRBPRT-1Bluetooth Receipt Printer

Royal Sovereign International, Inc. RBPRT-1 BLUETOOTH RECEIPT PRINTER Owner's Manual Please read and retain these instructions. www.royalsovereign.ca Français 9 Because our products are subject to continuous improvement, Royal Sovereign reserves the right to modify product design and specifications without notice and without incurring any obligation. E&OE 2 Safety Instructions∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 4 Interface∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 4 Installation and Operation∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙5 Self-checking∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6 Printer Maintenance∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6 Specification∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 7 Limited One Year Warranty ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 8 Français∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9 CONTENTS RBPRT-1 3 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a par ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.This device complies with par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be located or operating in conjunction with any other antenna or transmitter. IC warning statements: -English Warning Statement: -French Warning Statement: “Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The digital apparatus complies with Canadian CAN ICES ‐ 3 (B)/NMB ‐ 3(B). interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Operation is subject to the following two conditions: (1) this device may not cause This device complies with Industry Canada licence-exempt RSS standard(s). 4 SAFETY INSTRUCTIONS 1. Do not touch the printer cutter. 2. The print head is heating element. Do not touch it and its peripheral par ts during the printing process or when just finished printing. 3. To avoid possible damage to the unit, do not touch the surface of the print head or its connections. Other Notices: (1) To avoid possible vibration and shaking, place the printer on a flat surface. (2) Do not use the printer in a location with high temperature or humidity. (3) The power adapter should be connected to a power supply. Please try to avoid using the printer in a socket with other large electronic machines as this may cause voltage fluctuations. (4) Avoid contact with water or liquids. (5) Ensure the printer always has paper. Serious damage to the unit may occur if used without paper. (6) Disconnect the power supply if not used for an extended period of time. INTERFACE: USB: Universal USB interface (Standard B) USB Cash Drawer Power Supply RBPRT-1 5 INSTALLATION AND OPERATION 1. Connect the power supply to the back of the unit. Connect the RJ11 cable to the back of the unit 2. Connect the other end of the RJ11 cable to the cash drawer 3. Connect the power supply to an electrical outlet. Feeding the Receipt Paper (1) Open the top cover of printer. (2) Loading the paper roll as following picture. (3) Feed the paper and close the top cover of the printer. Description Power switch ON/OFF button Indicator Lights FEED Press to Feed the paper POWER Green light appears when unit is ON. ERROR The LED red light will appear in the following type of situations: No paper, Paper Jam, Print Head Overheat, etc. PAPER The red LED light will appear when the printer is out of paper. 6 Bluetooth pairing In order to have printer function with the Tab let , you will fir st need to pair the bluetooth printer with the tab let . Proceed as follows: 1. Ensure that the printer is turned 'ON' 2. On your tab let , in the setti ngs screen, turn ON the Bluetooth butto n 3. Pair the tab let with the printer . Enter the passcode 1234 3. You will see the unit is now Paired 4. Your receipt printer is now connected. Note: When pairin g, can not make multiple printers simul taneously turned on, otherwise it may not be possible to determine whi ch printer is successful pairing. Aft er the pairing is successful, the other PC can still be paired with the printer, each printer up with eight stage crew pairing, if more PC paired with the printer, then the earliest opportunity with the host printer printer from the pairing list automatically clear at this time if th…

Text truncated - open the document above for the full version.

Royal Sovereign International Inc Add: 2 Volvo Drive Rockleigh, NJ 07647 USA Tel: 201 750 1020 Fax: 201 750 1022 2014-10-27 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: 2ADGKRBPRT-1 We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics Diagram - Block Diagram - Operation description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Andrew Moon / QA Manager Contact information / address : 2 Volvo Drive Rockleigh, NJ 07647 USA Tel: 201 750 1020 Fax: 201 750 1022

IC: 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size:L:4cm*W:2cm Royal Sovereign International Inc Bluetooth Receipt Printer Model No.: RBPRT-1 FCC ID: 2ADGKRBPRT-1 IC: 12470A-RBPRT Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label location

IC : 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 4 1. INTERIOR PHOTOGRAPHS Fig.1 Fig.2 IC : 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 4 Fig.3 Fig.3 IC : 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 4 Fig.5 Fig.6 IC : 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 4 Fig.7 Fig.8 Antenna

IC: 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 37 FCC TEST REPORT For Royal Sovereign International Inc Bluetooth Receipt Printer Model No.: RBPRT-1 Prepared for : Royal Sovereign International Inc Address : 2 Volvo Drive Rockleigh, NJ 07647 USA Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Date of receipt of test sample : October 13, 2014 Number of tested samples : 1 Serial number : Prototype Date of Test : October 13, 2014 - October 24, 2014 Date of Report : October 24, 2014 IC: 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 37 FCC TEST REPORT FCC CFR 47 PART 15 C(15.247): 2013 Report Reference No. .............. : LCS1410130257E Date of Issue ................................ : October 24, 2014 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................ : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Testing Location/ Procedure ........ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : Royal Sovereign International Inc Address ........................................ : 2 Volvo Drive Rockleigh, NJ 07647 USA Test Specification Standard ....................................... : FCC CFR 47 PART 15 C(15.247): 2013 RSS-210 Issue 8/ RSS-Gen Issue 3 Test Report Form No. ................ : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : Bluetooth Receipt Printer Trade Mark .................................. : RS Model/ Type reference ................. : RBPRT-1 Ratings ......................................... : INPUT: AC100~240V, 0.5A, 50/60Hz OUTPUT: DC 12V/2.0A Result ......................................... : Positive Compiled by: Supervised by: Approved by: Tree Zhan/ File administrators Danny Huang / Technique principal Gavin Liang/ Manager IC: 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 37 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1410130257E October 24, 2014 Date of issue Type / Model........................... : RBPRT-1 EUT......................................... : Bluetooth Receipt Printer Applicant............................... : Royal Sovereign International Inc Address.................................. : 2 Volvo Drive Rockleigh, NJ 07647 USA Telephone............................... : / Fax.......................................... : / Manufacturer........................ : XIAMEN RONGTA TECHNOLOGY CO.,LTD. Address................................... : 3F-1/E Building, No.195 Gaoqishe, Gaodian Village, Dianqian Street Office, Huli District, Xiamen City Telephone............................... : / Fax.......................................... : / Factory................................... : XIAMEN RONGTA TECHNOLOGY CO.,LTD. Address................................... : 3F-1/E Building, No.195 Gaoqishe, Gaodian Village, Dianqian Street Office, Huli District, Xiamen City Telephone............................... : / Fax.......................................... : / IC: 12470A-RBPRT SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ADGKRBPRT-1 Report No.: LCS1410130257E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 37 TABLE OF CONTENTS Description ..................................................................................................................... Page 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................... 5 1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS ............................................................................................. 5 1.3. EXTERNAL I/O ...................................................................................................................................................... 5 1.4. DESCRIPTION OF TEST FACILITY ........................................................................................................................... 6 1.5. STATEMENT OF THE MEASUREMENT UNCERTAINTY ........................................................................................…

Text truncated - open the document above for the full version.