2ADINS6501LLTE Smart Phone

Getting Started With Your 4G LTE mobile phone Model: G5, S6501L 3 Front/Back G5 OverviewIndex G5 Overview 3 Setting up Your Phone 4 Safety information 6 Certificate 10 Warranty information & Registration 14 Customer Support 15 To p Bottom Wake/Sleep button Volume control Front camera Rear camera flash Type-C connector Headphone jack Main camera Secondary sensors Wide angle camera Earpiece Fingerprint sensor Speaker 45 Setting Up Your Phone Follow these step-by-step instructions to set up your G5. Power off the phone before inserting any cards! Remove SIM Tray • Remove the SIM tray by inserting a pin eject key/ paper clip in the small circular hole at the bottom of the tray. The tray will then eject from the phone. Configuration 2: microSD™ Card/SIM • Orient microSD/SIM card to match layout on tray. • microSD card supports up to 64GB • SIM 2 (Nano) supports 4GLTE connections. Configuration 1: Dual SIM Standby • Orient SIM card to match layout on tray. • SIM 1 (Nano) supports 4GLTE connections. • SIM 2 (Nano) supports 4GLTE connections. Replace SIM Tray • After placing the SIMs and/or memory card in the tray, slide it back into its slot. It will click and hold in place. Charge/Sync • Plug in the type C connector to charge the phone or transfer data. 1 3 2 4 5 Warning: SIM cards are small enough to become a choking hazard, so please keep them away from Children & Pets. SIM cards are also quite delicate. Please be careful when handling your card. 3 2 1 SIM 2SIM 1 SIM 1 MicroSD 67 Safety information • This section contains important information about the operation of your device, it also contains information about how to use the device safely. Read this information carefully before using your device. Electronic device Do not use your device if using the device is prohibited. Do not use the device if doing so causes danger or interference with other electronic devices. Interference with medical equipment • Follow rules and regulations set forth by hospitals and health care facilities. Do not use your device where prohibited. • Some wireless devices may affect the performance of hearing aids or pacemakers. Consult your service provider for more information. • Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket. Protecting your hearing when using a headset • To prevent possible hearing damage, do not listen at high volume levels for long periods. • Using a headset at high volumes may damage your hearing. To reduce this risk, lower the headset volume to a safe and comfortable level. • Exposure to high volumes while driving may cause distraction and increase your risk of an accident. Areas with flammables and explosives • Do not use the device where flammables or explosives are stored (in a gas station, oil depot, or chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. In addition, follow the instructions indicated in text or symbols. • Do not store or transport the device in containers with flammable liquids, gases, or explosives. Traffic security • Observe local laws and regulations while using the device. To reduce the risk of accidents, do not use your wireless device while driving. • Concentrate on driving. Your first responsibility is to drive safely. • Do not hold the device while driving. Use hands-free accessories. • When you must make or answer a call, pull off the road safely and park the vehicle first. • RF signals may affect the electronic systems of motor vehicles. For more information, consult the vehicle manufacturer. • Do not place the device over the air bag or in the air bag deployment area in a motor vehicle. Doing so may hurt you because of the strong force when the air bag inflates. • Wireless devices may interfere with the airplane’s flight system. Do not use your device where wireless devices are not allowed according to the airplane company’s regulations. Operating environment • Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in these environments may result in circuit malfunctions. Do not use your device during thunderstorms to protect your device against any danger caused by lightning. • Ideal operating temperatures are 0 °C to 35 °C. Ideal storage temperatures are -20 °C to 45 °C. Extreme heat or cold may damage your device or accessories. • Do not expose your device to direct sunlight (such as on a car dashboard) for prolonged periods. • To protect your device or accessories from fire or electrical shock hazards, avoid rain and moisture. • Keep the device away from sources of heat and fire, such as a heater, microwave oven, stove, water heater, radiator, or candle. • Do not place sharp metal objects, such as pins, near the earpiece or speaker. The earpiece may attract these objects and result in injury. • Stop using your device or applications for a while if the device is overheated. If skin is exposed to an overheated device for an extended period, low temperature burn symptoms, such as red spots and darker pigmentation, may occur. • Do not use your device’s camera flash directly in the eyes of people or pets. Otherwise temporary loss of vision or damage to the eyes may occur. • Do not touch the device’s antenna. Otherwise, communication quality may be reduced. • Do not allow children or pets to bite or suck the device or accessories. Doing so may result in damage or explosion. • Observe local laws and regulations, and respect the privacy and legal rights of others. Child safety • Comply with all precautions with regard to child’s safety. Letting children play with the device or its accessories may be dangerous. The device includes detachable parts that may present a choking hazard. Keep away from children. • The device and its accessories are …

Text truncated - open the document above for the full version.

Sun Cupid Technology (HK) Ltd DATE: 2020-07-16 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act asAgent On our behalf, I appoint Shenzhen Zhongjian Nanfang Testing Co.,Ltd.; 1st Floor, Block No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China；Bruce.Zhang, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Sun Cupid Technology (HK) Ltd , 16/F, CEO Tower, 77 Wing Hong Street, Cheung Sha Wan, Kowloon, Hong Kong. Dated this 2020-07-16 By: Danny Sit Signature Printed Title: Manager On behalf of : Sun Cupid Technology (HK) Ltd. Telephone: +852-2725 0161

Sun Cupid Technology (HK) Ltd DATE :2020-07-16 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ADINS6501L Product Name: LTE Smart phone Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operation description  BOM  Turn up These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2020-07-16 By: Danny Sit Signature Printed Title: Manager On behalf of : Sun Cupid Technology (HK) Ltd. Telephone: +852-2725 0161

Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 49 of 62 8 EUT Constructional Details Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 50 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 51 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 52 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 53 of 62

Label: Location:

Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 54 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 55 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 56 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 57 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 58 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 59 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 60 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 61 of 62 Report No: CCISE200607601 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282, Fax: +86-755-23116366 Page 62 of 62 ------End of report------

Shenzhen Zhongjian Nanfang Testing Co., Ltd. Report No: CCISE200607701 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the CCIS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC SAR REPORT Applicant: Sun Cupid Technology (HK) Ltd. Address of Applicant: 16/F, CEO Tower, 77 Wing Hong Street, Cheung Sha Wan, Kowloon, Hong Kong. Equipment Under Test (EUT) Product Name: LTE Smart phone Model No.: S6501L, G5 Trade mark NUU FCC ID: 2ADINS6501L Applicable standards: FCC 47 CFR Part 2.1093 Date of Test: 06 Jul., 2020 ~ 19 Jul., 2020 Test Result: Maximum Reported 1-g SAR (W/kg) Head: 0.719 Body: 0.558 Hotspot: 1.080 Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 2 of 213 2 Version Version No. Date Description 00 23 Jul., 2020 Original Tested by: Date: 23 Jul., 2020 Report Clerk Reviewed by: Date: 23 Jul., 2020 Project Engineer Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 3 of 213 3 Contents 1 COVER PAGE ....................................................................................................................................................... 1 2 VERSION ............................................................................................................................................................... 2 3 CONTENTS ........................................................................................................................................................... 3 4 SAR RESULTS SUMMARY ................................................................................................................................. 5 5 GENERAL INFORMATION .................................................................................................................................. 7 5.1 CLIENT INFORMATION ..................................................................................................................................................................... 7 5.2 GENERAL DESCRIPTION OF EUT ................................................................................................................................................... 7 5.3 MAXIMUM RF OUTPUT POWER ...................................................................................................................................................... 8 5.4 ENVIRONMENT OF TEST SITE ......................................................................................................................................................... 9 5.5 TEST LOCATION ............................................................................................................................................................................. 9 6 INTRODUCTION ................................................................................................................................................. 10 6.1 INTRODUCTION ............................................................................................................................................................................. 10 6.2 SAR DEFINITION .......................................................................................................................................................................... 10 7 RF EXPOSURE LIMITS ..................................................................................................................................... 11 7.1 UNCONTROLLED ENVIRONMENT ................................................................................................................................................... 11 7.2 CONTROLLED ENVIRONMENT ....................................................................................................................................................... 11 7.3 RF EXPOSURE LIMITS .................................................................................................................................................................. 11 8 SAR MEASUREMENT SYSTEM ....................................................................................................................... 12 8.1 E-FIELD PROBE............................................................................................................................................................................ 13 8.2 DATA ACQUISITION ELECTRONICS (DAE) .................................................................................................................................... 13 8.3 ROBOT ..........................................................................…

Text truncated - open the document above for the full version.

Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 101 of 213 Test Laboratory: CCIS Date/Time: 07.06.2020 13:45:29 DUT: LTE Smart phone; Type: S6501L; Serial: 1# Communication System: UID 0, UMTS-FDD(WCDMA) (0); Frequency: 1712.4 MHz; Duty Cycle: 1:1 Medium parameters used (interpolated): f = 1712.4 MHz; σ = 1.332 S/m; ε r = 41.178; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.4, 8.4, 8.4); Calibrated: 08.30.2019;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 08.09.2019  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) WCDMA 1700 Left Cheek/Low Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 0.0900 W/kg SAR(1 g) = 0.056 W/kg; SAR(10 g) = 0.034 W/kg Maximum value of SAR (measured) = 0.0764 W/kg WCDMA 1700 Left Cheek/Low Channel/Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.0953 W/kg 0 dB = 0.0953 W/kg = -10.21 dBW/kg Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 102 of 213 Test Laboratory: CCIS Date/Time: 07.06.2020 11:14:57 DUT: LTE Smart phone; Type: S6501L; Serial: 1# Communication System: UID 0, UMTS-FDD(WCDMA) (0); Frequency: 1907.6 MHz; Duty Cycle: 1:1 Medium parameters used (interpolated): f = 1907.6 MHz; σ = 1.426 S/m; ε r = 40.214; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.17, 8.17, 8.17); Calibrated: 08.30.2019;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 08.09.2019  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) WCDMA 1900 Left Cheek/High Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 0.0260 W/kg SAR(1 g) = 0.015 W/kg; SAR(10 g) = 0.008 W/kg Maximum value of SAR (measured) = 0.0218 W/kg WCDMA 1900 Left Cheek/High Channel/Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.0196 W/kg 0 dB = 0.0196 W/kg = -17.08 dBW/kg Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 103 of 213 Test Laboratory: CCIS Date/Time: 07.06.2020 14:16:57 DUT: LTE Smart phone; Type: S6501L; Serial: 1# Communication System: UID 0, LTE-Fdd(USA) 1RB QPSK (0); Frequency: 1860 MHz; Duty Cycle: 1:1 Medium parameters used (interpolated): f = 1860 MHz; σ = 1.412 S/m; ε r = 40.348; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.17, 8.17, 8.17); Calibrated: 08.30.2019;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 08.09.2019  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) LTE Band 2 1RB(20MHz) Left Cheek/Low Channel/Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.0303 W/kg LTE Band 2 1RB(20MHz) Left Cheek/Low Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 3.371 V/m; Power Drift = 0.17 dB Peak SAR (extrapolated) = 0.0290 W/kg SAR(1 g) = 0.011 W/kg; SAR(10 g) = 0.00619 W/kg Maximum value of SAR (measured) = 0.0138 W/kg 0 dB = 0.0138 W/kg = -18.60 dBW/kg Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: [email protected] Page 104 of 213 Test Laboratory: CCIS Date/Time: 07.06.2020 15:20:58 DUT: LTE Smart phone; Type: S6501L; Serial: 1# Communication System: UID 0, LTE-Fdd(USA) 1RB QPSK (0); Frequency: 1720 MHz; Duty Cycle: 1:1 Medium parameters used (interpolated): f = 1720 MHz; σ = 1.336 S/m; ε r = 41.05; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration:  Probe: EX3DV4 - SN3924; ConvF(8.4, 8.4, 8.4); Calibrated: 08.30.2019;  Sensor-Surface: 1.4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1373; Calibrated: 08.09.2019  Phantom: SAM 5.0; Type: QD000P40CD; Serial: TP:1765  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) LTE Band 4 1RB(20MHz) Left Cheek/Low Channel/Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.118 W/kg LTE Band 4 1RB(20MHz) Left Cheek/Low Channel/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 1.585 V/m; Power Drift = 0.36 dB Peak SAR (extrapolated) = 0.121 W/kg SAR(1 g) = 0.078 W/kg; SAR(10 g) = 0.048 W/kg Maximum value of SAR (measured) = 0.104 W/kg 0 dB = 0.104 W/kg = -9.83 dBW/kg Report No: CCISE200607701 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006077 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366, E-mail: inf…

Text truncated - open the document above for the full version.

EUT Photos (Model: S6501L) EUT Antenna Locations SAR Test Setup Photos Head Right Cheek Right Tilted Left Cheek Left Tilted Body Front side (10mm) Back side(10mm) Top side(10mm) Bottom side(10mm) Left side(10mm) Right side(10mm)

Shenzhen Zhongjian Nanfang Testing Co., Ltd. Report No: CCISE200607605 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the CCIS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC REPORT (UNII) Applicant: Sun Cupid Technology (HK) Ltd. Address of Applicant: 16/F, CEO Tower, 77 Wing Hong Street, Cheung Sha Wan, Kowloon, Hong Kong. Equipment Under Test (EUT) Product Name: LTE Smart phone Model No.: S6501L, G5 Trade mark: NUU FCC ID: 2ADINS6501L Applicable standards: FCC CFR Title 47 Part 15 Subpart E Section 15.407 Date of sample receipt: 24 Jun., 2020 Date of Test: 25 Jun., to 09 Jul., 2020 Date of report issued: 14 Jul., 2020 Test Result: PASS* * In the configuration tested, the EUT complied with the standards specified above. Report No: CCISE200607605 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 2 of 78 2 Version Version No. Date Description 00 14 Jul., 2020 Original Tested by: Date: 14 Jul., 2020 Test Engineer Reviewed by: Date: 14 Jul., 2020 Project Engineer Report No: CCISE200607605 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE2006076 No.110~116, Building B, Jinyuan Business Building, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 3 of 78 3 Contents Page 1 COVER PAGE ................................................................................................................................................... 1 2 VERSION ........................................................................................................................................................... 2 3 CONTENTS ....................................................................................................................................................... 3 4 TEST SUMMARY .............................................................................................................................................. 4 5 GENERAL INFORMATION .............................................................................................................................. 5 5.1 CLIENT INFORMATION .................................................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF E.U.T. ............................................................................................................................... 5 5.3 TEST ENVIRONMENT AND TEST MODE ........................................................................................................................... 7 5.4 DESCRIPTION OF SUPPORT UNITS ................................................................................................................................ 7 5.5 MEASUREMENT UNCERTAINTY...................................................................................................................................... 7 5.6 ADDITIONS TO, DEVIATIONS, OR EXCLUSIONS FROM THE METHOD .............................................................................. 7 5.7 RELATED SUBMITTAL(S) / GRANT (S) ........................................................................................................................... 7 5.8 LABORATORY FACILITY ................................................................................................................................................. 8 5.9 LABORATORY LOCATION ............................................................................................................................................... 8 5.10 TEST INSTRUMENTS LIST ............................................................................................................................................ 9 6 TEST RESULTS AND MEASUREMENT DATA ........................................................................................... 10 6.1 ANTENNA REQUIREMENT ............................................................................................................................................. 10 6.2 CONDUCTED EMISSION ............................................................................................................................................... 11 6.3 CONDUCTED OUTPUT POWER .................................................................................................................................... 14 6.4 OCCUPY BANDWIDTH .................................................................................................................................................. 22 6.5 POWER SPECTRAL DENSITY ................................................................................................…

Text truncated - open the document above for the full version.