2ADK3-PR037Wireless Charging Pad

Function: 1. Wireless charging Pad 2. LED indicator 3. Type-C USB input Port What include: 1 x Wireless Charging Pad 1 x USB-C to Type-C Charging Cable 1 x Instruction Manual Specs. Input: 5V/2A; 9V/2A; Wireless Output: 5W/7.5W/10W/15W Instructions:  Connect the provided Type-C USB to USB-C cable to the Type-C USB input port (3), then connect the USB end of the cable to a power source ( not include) which can support 5V/2A or 9V/2A.  LED indicator(3) will flash BLUE&RED alternately 3 times, then glow RED to indicate the wireless charger is in standby mode and ready to begin charging.  Place the wireless charging supported mobile phone/device upright on the wireless charging surface(1) ,LED will glow BLUE when device is charging.  Phone will begin to charge automatically.  Once fully charged remove the device 1 2 3 Note: When wireless charging, if the Led indicator flash RED the device is either NOT a wireless charging device or there is an object between the the device and charging surface interfering with the charging process. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

(XING DA INTERNATIONAL ELECTRONICS LIMITED) (October 25, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2ADK3-PR037) [XING DA INTERNATIONAL ELECTRONICS LIMITED] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Sam Shen (XING DA INTERNATIONAL ELECTRONICS LIMITED) (October 25, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2ADK3-PR037) [XING DA INTERNATIONAL ELECTRONICS LIMITED] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Sam Shen

XING DA INTERNATIONAL ELECTRONICS LIMITED (October 25, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (Wireless Charging Pad / XY-PR037 / FCC ID: 2ADK3-PR037) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☒ Internal Photos ☐ NOTE 1 ☒ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Signature: Name: Sam Shen Title: Sales

XING DA INTERNATIONAL ELECTRONICS LIMITED (October 25, 2023) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen CTB Testing Technology Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature: Name: Sam Shen Title: Sales

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 5 Model: XY-PR037 External Photos Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 5 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 5 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 4 of 5

FCC ID LABEL: Label Location: FCC ID: 2ADK3-PR037 Model No.: XY-PR037

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 3 Model: XY-PR037 Internal Photos ANT Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 3 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 3

ANT PHTOT L W H 98mm±0.2 55mm±0.2 0.2mm±0.1 All measurements were performed radiated and therefore additional antenna gain documentation is not required.

TEST REPORT Compiled by: Reviewed by: Approved by: Arron Liu Bin Mei Rita Xiao / Director Note: If there is any objection to the inspection results in this report, please submit a written report to the company within 15 days from the date of receiving the report. The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. “*” indicates the testing items were fulfilled by subcontracted lab. “#” indicates the items are not in CNAS accreditation scope. Product Name: Wireless Charging Pad FCC ID: 2ADK3-PR037 Trademark: N/A Model Number: XY-PR037 Prepared For: XING DA INTERNATIONAL ELECTRONICS LIMITED Address: #98 LiWu Swan Industrial District,Qiao Tou Town,Dong Guan City,Guang Dong,China Manufacturer: Dongguan Xing Yue Electronic co., Ltd Address: #98 LiWu Swan Industrial District,Qiao Tou Town,Dong Guan City,Guang Dong,China Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: 1&2/F., Building A, No.26, Xinhe Road, Xinqiao, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: Oct. 13, 2023 Sample tested Date: Oct. 13, 2023 to Oct. 18, 2023 Issue Date: Oct. 18, 2023 Report No.: CTB231018042RFX Test Standards FCC Part 15 C Test Results PASS Remark: This is wireless charger radio test report. Shenzhen CTB Testing Technology Co., Ltd. Report No.:CTB231018042RFX Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 21 TABLE OF CONTENTS 1. GENERAL INFORMATION ........................................................................................................................ 3 1.1. Report information ................................................................................................................................. 3 1.2. Measurement Uncertainty ..................................................................................................................... 3 1.3. Test Facility ........................................................................................................................................... 3 1.4. Test Uncertainty .................................................................................................................................... 4 2. PRODUCT DESCRIPTION ......................................................................................................................... 5 2.1. EUT Description .................................................................................................................................... 5 2.2. Block Diagram of EUT Configuration ..................................................................................................... 5 2.3. Test Conditions ..................................................................................................................................... 5 2.4. DescriptionOfSupport Units (Conducted Mode) .................................................................................... 6 3. TEST RESULTS SUMMARY ...................................................................................................................... 6 4. TEST EQUIPMENT USED .......................................................................................................................... 7 4.1. MEASUREMENT INSTRUMENTS LIST ............................................................................................... 7 5. CONDUCTED EMISSION TEST ................................................................................................................. 9 5.1. Block Diagram of Test Setup ................................................................................................................. 9 5.2. Test Standard ........................................................................................................................................ 9 5.3. Conducted Emission Limit ..................................................................................................................... 9 5.4. EUT Configuration on Test .................................................................................................................... 9 5.5. Operating Condition of EUT ................................................................................................................ 10 5.6. Test Procedure .................................................................................................................................... 10 5.7. Test Result .......................................................................................................................................... 10 6. RADIATED EMISSION MEASUREMENT ................................................................................................ 13 6.1. Block Diagram of Test Setup ............................................................................................................... 13 6.2. Test Standard ...................................................................................................................................... 14 6.3. EMI Test Receiver Setup..................................................................................................................... 14 6.4. Test Procedure .................................................................................................................................... 14 6.5. Test Result .......................................................................................................................................... 14 7. OCCUPIED BANDWIDTH ........................................................................................................................ 18 7.1. Block Diagram of Test Setup ..........................................................................................…

Text truncated - open the document above for the full version.

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 3 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 3 Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 3 of 3

Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 2 Model: XY-PR037 Radiated Emission 9KHz-30MHz 30MHz-1GHz Shenzhen CTB Testing Technology Co., Ltd. Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 2 Conducted emissions