2ADNQFTF21BTInfrared Thermometer

- 1 - Instruction for Use lnfrared Thermometer (Contact Type) FT-F11-BT,FT-F21-BT, FT-F12-BT, FT-F22-BT FT-F11, FT-F21, FT-F12, FT-F22 UO8080, UO8080E - 2 - FT-F11-BT&FT-F11 FT-F21-BT & FT-F21 INFRARED THERMOMETER (FT-F11-BT, FT-F21-BT, FT-F12-BT, FT-F22-BT; FT-F11, FT-F21, FT-F12, FT-F22, UO8080, UO8080E) Operating Instruction Please read carefully before use. DESCRIPTION 1. Table of Contents 1. Product Listing 2. Product Overview 3. Outline Drawing 4. The Definition of Symbols 5. Measuring 6. Battery Voltage Display & Replacement 7. Operation Precautions 8. Precaution for Measuring Temperature 9. Product Specification 10. Common question concerning forehead temperature 2. Product Overview This infrared Thermometer measure the temperature. It can get more quick and accurate from human body temperature. This product has the following advantages: 1). Easy to Clean the Probe. 2). High speed & Accuracy scan the reading of temperature. 3). Convenience, Only one key operation. 4). 12 memories recall. 5). Last measured temperature data displayed, when you turn on the power. 3. Outline Drawing - 3 - FT-F12-BT &FT-F12 FT-F22-BT&FT-F22 4.The Definition of Symbols Reading Display Ear Measuring mode (Suitable for FT-F11, FT-F12 & FT-F21, FT-F22 FT-F11-BT, FT-F21-BT; FT-F12-BT, T-F22-BT; UO8080) Forehead Measuring mode (Suitable for FT-F21，FT-F22 & FT-F21-BT FT-F22-BT, UO8080E) Celsius Scale Fahrenheit Scale Low Battery Last Memorized Temperature Display 5. Measuring 1) Ear Measuring Mode (Figure 5.1) (Suitable for FT-F11, FT-F11-BT, FT-F21, FT-F21-BT, FT-F12,FT-F12-BT,FT-F22,FT-F22-BT,UO8080, UO8080E) ●Turn on the “power” button key of the IR Thermometer and then all displayed segments appear briefly as like on(Figure 5.2); the displayed screen appears last measured temperature data, please see on (Figure 5.3); after few seconds automatically change to the Ear Measuring Mode ” ” symbol appears on the displayed screen and the - 4 - temperature unit“” or “” blink it’s ready to measure, please see on( Figure 5.4) ●Insert the IR Thermometer probe into the ear canal as on the following (Figure 5.1); Pull the ear slightly back ward to straighten the ear canal. Then insert the probe into the ear as far as it goes. Be sure the probe fully seals the ear canal. Hold this position until the measurement is completed. ●Press the “ SCAN “ button key to wait about 1 second then you can hear the long “Bi--” sound that it’s finished the measurement in the meantime the measured temperature data appears on the displayed screen. (Figure 5.5) ●Remove the IR thermometer from the ear canal and read measured data on the displayed screen. If you don’t use again, the power will be automatically switch off within 60 seconds. Figure 5.1 Figure 5.2 Figure 5.3 Figure 5.4 Figure 5.5 2) Contact Type Forehead Measuring mode (Figure5.1A）(Suitable for FT-F21，FT-F22 & FT-F21-BT,FT-F22-BT, UO8080E) ●Turn on the “power” button key of the IR Thermometer and then all displayed segments appear briefly as like on(Figure 5.2A),the displayed screen appears last measured temperature data, please see on (Figure 5.3A),after few seconds automatically change to the Forehead Measuring Mode “ ” symbol appears on the displayed screen and the temperature unit “ ”or “” blink then it’s ready to measure, please see on (Figure 5.4A). ●Put the probe in the middle of forehead position and press the “SACN” button key then keep moving the IR thermometer from the middle of forehead to the side of forehead then you will hear long “Bi--” sound that It is finished the measurement in the meantime the measured temperature data appears on the displayed screen, the measuring time takes about 1 second .(see on Figure 5.5A). ●Remove the IR thermometer from the forehead and read measured data on the displayed screen. If you don’t use again, the power will be automatically switch off within 60 seconds. Figure 5.1A Figure 5.2A Figure 5.3A Figure 5.4A Figure 5.5A - 5 - 3）“” and“”adjust (Suitable for FT-F11，FT-F21,FT-F11-BT,FT-F21-BT, UO8080, UO8080E) ● On power off condition, press the “SCAN” button key about 5 seconds until the displayed screen appears “- - -” and “” or “” temperature unit blinks . In this condition, press the “SCAN” button key again to adjust “””or “” and then it is set up ready for use. “” and“”adjust (Suitable for FT-F12，FT-F22,FT-F12-BT,FT-F22-BT) ●On power off condition, press the “SCAN” button about 10 seconds until the displayed screen appears “ - - -” and “” or “” temperature unit blinks . In this condition, press the “SCAN” button key again to adjust “ ””or “” and then it is set up ready for use. 4）Ear and Forehead measuring mode switch ●On power off condition, press the “Power” button about 5 seconds until the displayed screen appears or then press the “Scan” button to switch to ear or forehead measuring mode. 5）Memory recall ●12 memories recall. ●Press “SCAN” button key to display “---M” on the displayed screen, in the power off condition and then memory recall displays. ●Press again “SCAN” button key to display previous memory in order and the memory will recall in one second. ●Press “Power” button key to be out of memory recall and then enter process condition to measure. 6. Battery Voltage Display & Replacement ●LOW battery: The low battery symbol will be shown at the lower batter on the displayed screen during the low battery power. Replace the battery as soon as possible. However you can continue to use it on short time. (Figure 6.1) Figure 6.1 ●Replace battery: 1). Open battery cover, remove the old battery out. 2). Insert new battery inside the bottom, please be careful the batteries polarity. - 6 - 7. Operation Precautions 1). Please insert the battery into the bracket when do you use the IR Thermometer on first time. 2). Please keep the probe clean after you used the IR Thermometer. 3). Please keep the IR Thermometer dry and never immerse it in water or any liquid. 4). Do not put the IR Thermometer under high temperature environment o…

Text truncated - open the document above for the full version.

Fudakang Industrial Co., Ltd Address :No.8 Yinghe Road, Yuanjiangyuan Management Zone, Changping Town, Dongguan City, Guangdong Province ,China Tel: 86-769-81098181 Fax: 86-769-81098187 Website: www.fudakang.com Email: [email protected] Request for Confidentiality Date: 2015/06/29 Subject: Confidentiality Request for: FCC ID 2ADNQFTF21BT Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ Fudakang Industrial Co., Ltd has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: Bob Yu (Signature/Title 3 ) (Print name)

1 Photographs - EUT Constructional Details Test model No.: FT-F21-BT

1 Photographs - EUT Constructional Details Test model No.: FT-F21-BT

UnitQ'ty PCS1 PCS1 PCS2 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS2 PCS3 21 PCS3 PCS1 PCS1 PCS1 PCS1 PCS7 PCS2 PCS2 PCS2 PCS1 PCS1 PCS1 PCS1 22.11 1R-S10330-01SMD Resistor 10KΩ ±1% 0603R 22.9 1P-F11122-03 FT-F11-BT PCB (BT version) FT-F11-BT PCB(BT version) 50.2*30.0*1.2mm version:FT-F11-BT4 22.10 1R-S10230-01SMD Resistor 1K ±1% 0603R 22.7 1C-S22050-01SMD Capacitor 22p F ±5% 50V 0603C 22.8 1D-SMSS34-01Diode SS34 D0-214AC 22.5 1C-S10516-01SMD Capacitor 1uF ±10% 16V 0805 22.6 1C-S10616-02SMD Capacitor 10uF +10/-10% X7R 16V 0805 22.3 1C-D10725-03Capacitor 100uF/ ± 20% 10V 4*7mm DIP 22.4 1C-S10450-03SMD Capacitor 0.1uF ±10% 50V Y5V 0603(100nF) 22.1 0A-BF1154-01MCU IC U1 HM104 DICE package (AKX) 22.2 0C-B24C02-01SMD IC HTL24C02,SO-8 4S-S23080-01Screw OD 2.3*8mm 22 7Z-CBF110-10FT-F11-BT COB with BT FT-F11-BT COB with Blue Tooth 19 4S-S15050-01Screw OD 1.5*5mm 20 4S-S20060-01Screw OD 2*6mm 17 4C-S20938-01"+/-" Spring (FT-F11) 21*9.7*1.5mm 18 4C-S70910-01"-" Spring (FT-F11) 9*14.5*1.5 15 3R-X38630-01Anti slip mat OD 6mm T3.0 16 4C-S15910-01"+" Spring(FT-F11) 9*14.5*1.5 13 3P-FF1169-05 Probe fixed base(FT- F11) ABS 14 3R-C28233-01Bus bar L28.5*W2.0*H3.3mm,P=0.1 11 3P-FF1169-20 Probe fixed cover(FT- F11) ABS 12 3P-FF2169-02 Forehead fixed cover(FT-F21) ABS 9 3P-FF1164-03Power button(FT-F11) ABS 10 3P-FF1169-06 Measuring button(FT- F11) ABS 7 3P-FF1139-01Upper case(FT-F11) ABS 8 3P-FF1149-01Buttom case(FT-F11) ABS 5 2W-A43022-05Jumping Wire (Black) 30*2*2mm,OD 0.8mm black 6 3P-FF1129-01Battery Cover(FT-F11) ABS 4 2W-A43022-04Wire (RED) 30*2*2mm OD 0.8mm,red 1 1L-292412-02LCD ET_LCD 29*24 (888.8 display) 2 2B-Y20154-01 BeepOD 20mm FT-F21-BT BOM ItemPart No.MaterialDescription 3 2W-A28022-04Wire (black) 80*2*2mm,OD 1.0mm black 第 1 页，共 2 页 UnitQ'ty FT-F21-BT BOM ItemPart No.MaterialDescription PCS1 PCS1 PCS1 PCS1 PCS2 PCS1 PCS1 PCS1 PCS2 PCS1 PCS1 PCS1 PCS1 PCS1 M0.072 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 PCS1 26 5L-FDKF11-02Display cover (FT-F11) Acrylic (PMMA) 25 7Z-SFBT41-01BT Modular Blue tooth modular SL02_V1 24.9 1S-WFTF41-02Thermopile 10TP583T Thermopile(Ishizuka) 24.10 4C-C50220-01 Positon fixed copper ring OD 5.05mm T 0.2mm H 1.85mm,copper 24.7 4C-A65560-02 Thermopile Modular(buttom) Copper plating nickal OD 6.5 x 5.6mm 24.8 4C-C86207-01Thermopile Modular(up) Alluminum OD 8.6, L 20.75mm 24.5 3R-X14000-01Heating tube OD 1.4mm 24.6 3S-X40500-01Silicon ring OD 4mm,wire diameter:0.5mm 24.3 2W-A25022-03Jumping Wire (Blue) 50*2*2mm,OD 1.0mm,blue 24.4 2W-A25022-04Jumping Wire (Green) 50*2*2mm,OD 1.0mm,Green 24.1 2W-A25022-01Wire (RED) 50*2*2mm,OD 1.0mm,red 24.2 2W-A25022-02Wire (Black) 50*2*2mm,OD 1.0mm,black 22.19 1Y-040003-02Crytal 4.0MHz ф3*8MM DIP 20PF 22.20 2S-TD13XA-01SMD Button TD-13XA 24 8Z-FDF11C-02Themoplie Modular FT-F21-BT Themoplie Modular 22.17 1R-S40430-01SMD Resistor 402KΩ ±1% 0603 22.18 1T-P85502-01Transistor SOT 23 8550(2TY) PNP typr hfe=200-350 22.15 1R-S20430-01SMD Resistor 200KΩ ±1% 0603 22.16 1R-S3003B-01SMD Resistor 30Ω 5% 0603 22.13 1R-S10521-01SMD Resistor 1MΩ ±5% 0603 22.14 1R-S20125-01SMD Resistor 200Ω ±5% 0603 22.12 1R-S10430-01SMD Resistor 100K ±1% 0603R 第 2 页，共 2 页

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150600347704 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1506003477CR (SGS GZ No.:GZME1506000491ME) Applicant: FUDAKANG INDUSTRIAL CO., LTD. Manufacturer/ Factory: FUDAKANG INDUSTRIAL CO., LTD. Product Name: Infrared Thermometer Model No.(EUT): FT-F21-BT Add Model No.: FT-F21, FT-F11-BT, FT-F11, UO-8080, UO-8080E Trade Mark: FDK FCC ID: 2ADNQFTF21BT Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05r02 Date of Receipt: 2015-06-16 Date of Test: 2015-07-03 to 2015-07-13 Date of Issue: 2015-07-20 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150600347704 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-07-20 Original Authorized for issue by: Tested By 2015-07-13 (Eric Fu) /Project Engineer Date Prepared By 2015-07-20 (Jade Chen) /Clerk Date Checked By 2015-07-20 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150600347704 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150600347703 Page: 1 of 62 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1506003477CR(SGS GZ No.:GZME1506000491ME) Applicant: FUDAKANG INDUSTRIAL CO., LTD. Manufacturer/ Factory: FUDAKANG INDUSTRIAL CO., LTD. Product Name: Infrared Thermometer Model No.(EUT): FT-F21-BT Add Model No.: FT-F21, FT-F11-BT, FT-F11, UO-8080, UO-8080E Trade Mark: FDK FCC ID: 2ADNQFTF21BT Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-06-16 Date of Test: 2015-07-03 to 2015-07-13 Date of Issue: 2015-07-20 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150600347703 Page: 2 of 62 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-07-20 Original Authorized for issue by: Tested By 2015-07-13 (Eric Fu) /Project Engineer Date Prepared By 2015-07-20 (Jade Chen) /Clerk Date Checked By 2015-07-20 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150600347703 Page: 3 of 62 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test m…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: FT-F21-BT 1.1 Radiated Emission 1.2 Radiated Spurious Emission