2ADOV-IRULUU1PROMobile phone

Android Platform to introduce and use of guidance Mobile phone U1PRO iRULU July 2014 Version 4.4.2 FCC Regulations This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna. ‐Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. The antenna(s) used for this transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. RF Exposure Information (SAR) This mobile phone meets the government’s requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The highest SAR value for the model phone as reported to the FCC when tested for use at the ear is 0.567 W/kg and when worn on the body, as described in this user guide, is 0.965W/kg (Body‐worn measurements differ among phone models, depending upon available accessories and FCC requirements.) While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: 2ADOV-IRULUU1PRO. For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and the positions the handset a minimum of 1.0 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. If you do not use a body‐worn accessory and are not holding the phone at the ear, position the handset a minimum of 1.0 cm from your body when the phone is switched on. Please make sure the temperature for production unit will be between ‐10~50 ̊C. - 2 - CONTENTS How Introduction........................................................................................................ - 5 - Introduction phone keys........................................................................................... - 5 - Introduction widgets.................................................................................................. - 5 - Information Function................................................................................................. - 5 - Emoji Keyboard..................................................................................................-9- Contact Features................................................................................................... ....- 9 - Call History Features.............................................................................................. - 11 - Dail and caller ID display.............................................................................................-12- Paste the text / copy Features............................................................................... - 12 - E-mail Features....................................................................................................... - 14 - Desktop Features.................................................................................................... - 16 - New lock screen and color schemes................................................................-16- Wallpapers ......................................................................................................-17- Application packet................................................................................................... - …

Text truncated - open the document above for the full version.

USA111 INC. 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Tel: 614-8360241 DOC ATTESTATION LETTER FCC ID: 2ADOV-IRULUU1PRO Date: Jan. 22, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: I, the undersigned, hereby attest to the fact that I will apply the Declaration of Conformity procedure to the computer peripheral. I understand the following FCC requirements: 1. Devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. 3. Pt 2.1077 contains the list of information that must be included in the Declaration of Conformity, which must be supplied with each product sold. The DoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(c)(2), the responsible party is either the Manufacturer or if the product is imported the Importer. Sincerely, Carolyn Schafer / Director

USA111 INC. 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Tel: 614-8360241 DATE 01-22-2015 FCC ID: 2ADOV-IRULUU1PRO Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Shenzhen CTL Testing Technology Co., Ltd.(MR. Tracy Qi) at Floor 1-A, Baisha Technology Park, No. 3011, Shahexi Road, Nanshan, Shenzhen 518055 China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with USA111 INC. at 8F, Dawning Building, Hi-tech Industrial Park, Nanshan District, Shenzhen, China. Dated this 01-22-2015 Agency agreement expiration date: 01-21-2016 By: Carolyn Schafer Signature Printed Title: Director On behalf of : USA111 INC. Telephone: 614-8360241

USA111 INC. 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Tel: 614-8360241 DATE 01-22-2015 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ADOV-IRULUU1PRO Product Name: Mobile phone Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description • Tune up Procedure • BOM These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 01-22-2015 By: Carolyn Schafer Signature Printed Title: Director On behalf of : USA111 INC. Telephone: 614-8360241

USA111 INC. 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Tel: 614-8360241 Letter for Label Proposal FCC ID: 2ADOV-IRULUU1PRO Date: Jan. 22, 2015 Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Dear Sirs: USA111 INC. requests acceptance of the labeling proposal described below for transceivers bearing FCC identifier 2ADOV-IRULUU1PRO. The subject transceivers are compact handheld models as shown in figure 1, authorized under FCC Part 22/24 for mobile services. Figure 1. Because the majority of the transceiver housing is composed of display, speaker, operating controls, and a removable battery pack, there is extremely limited space available to attach the required label carrying the FCC identifier. Attaching the label to the battery pack is not acceptable because the battery pack is a removable item. For this reason, we propose placing the label carrying the FCC identifier inside the battery compartment as shown in figure 2. FCC ID Label USA111 INC. 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Tel: 614-8360241 Proposed Label Location on EUT Figure 2. The consumer packaging for these models includes the battery pack as a separate item, NOT installed on the radio. As such, the FCC identifier will be readily visible to the user before the battery pack is installed and whenever the battery pack is removed or replaced. In this location, the label will also be protected from physical abuse and remain readable for the anticipated life of the device. The consumer packaging for these models is a "gift box" which does not allow the transceiver to be seen at time of purchase. In order to meet the requirements of 47CFR Part 2.925 (d), We will add the FCC identifier "2ADOV-IRULUU1PRO" to the outside of the consumer "gift box" packaging. Sincerely yours, Carolyn Schafer / Director

External Photos of EUT

FCC ID Label Information 1. Label location: 2. FCC ID Label: iRULU Model: U1PRO GSM/GPRS 850/900/1800/1900 WCDMA/HSPA 850/1900/2100 FCC ID: 2ADOV-IRULUU1PRO FCC ID Label

Internal Photos of EUT

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-26636041 SAR TEST REPORT Report Reference No. .................... : FCC ID. ............................................ : CTL1412193074-SAR 2ADOV-IRULUU1PRO Compiled by ( position+printed name+signature) .. : File administrators Happy Guo Supervised by ( position+printed name+signature) .. : Test Engineer Jacky Chen Approved by ( position+printed name+signature) .. : Manager Tracy Qi Date of issue ..................................... : Dec 30, 2014 Representative Laboratory Name . : Shenzhen CTL Electromagnetic Technology Co., Ltd. Address............................................. : Floor 1-A, Baisha Technology Park, No. 3011, Shahexi Road, Nanshan, Shenzhen 518055 China. Testing Laboratory Name .............. : The Testing and Technology Center for Industrial Products of Shenzhen Entry-Exit Inspection and Quarantine Bureau Address............................................. : No.289, 8th Industry Road, NanshanDistrict,Shenzhen,Guangdong Applicant’s name ............................ : USA 111 INC. Address............................................. : 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Test specification .......................... : Standard ........................................... : ANSI C95.1–1999 47CFR §2.1093 TRF Originator .................................. : Shenzhen CTL Electromagnetic Technology Co., Ltd. Master TRF ....................................... : Dated 2011-01 Shenzhen CTL Electromagnetic Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Electromagnetic Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Electromagnetic Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Mobile phone Trade Mark ....................................... : iRULU Manufacturer ................................... : Shenzhen Allland Networking Co., Ltd. Model/Type reference ....................... : U1PRO Operation Frequency ......................... GSM 850MHz/PCS1900MHz/WiFi/BT/UMTS Band II/V Modulation Type ................................ GSM(GMSK, 8PSK), Bluetooth(GFSK,8DPSK,Π/4DQPSK), DSSS(CCK,DQPSK,DBPSK),OFDM(64QAM,16QAM,QPSK, BPSK), UMTS(QPSK) Hardware version ............................. : G807 J3 V1.3 Software version .............................. : G807_J3_ZX_N2_U1PRO_1028 Rating ............................................... : DC 3.80V Android version ................................. : Android 4.4.2 Result ................................................ : PASS V1.0 Page 2 of 102 Report No.: CTL1412193074-SAR T E S T R E P O R T Test Report No. : CTL1412193074-SAR Dec 30, 2014 ______________________________________________________________________________________________ Date of issue Equipment under Test : Mobile phone Model /Type : U1PRO Listed Models : / Applicant : USA 111 INC. Address : 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Manufacturer : Shenzhen Allland Networking Co., Ltd. Address : Fourth Floor, #B Building, Weiyulong Industrial Park, Xuegang North Road #16, Bantian Street, Longgang District, Shenzhen Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. V1.0 Page 3 of 102 Report No.: CTL1412193074-SAR ** Modifited History ** Revison Description Issued Data Remark Revsion 1.0 Initial Test Report Release 2014-12-30 Tracy Qi V1.0 Page 4 of 102 Report No.: CTL1412193074-SAR Contents 1. T E S T S T A N D A R D S 6 2. S U M M A R Y 7 2.1. General Remarks 7 2.2. Product Description 7 2.3. Statement of Compliance 8 2.4. Equipment under Test 9 2.5. EUT configuration 9 3. T E S T E N V I R O N M E N T 10 3.1. Address of the test laboratory 10 3.2. Test Facility 10 3.3. Environmental conditions 10 3.4. SAR Limits 10 3.5. Equipments Used during the Test 11 4. S A R M E A S U R E M E N T S S Y ST E M C O N F I G U R A T I O N 12 4.1. SAR Measurement Set-up 12 4.2. DASY5 E-field Probe System 13 4.3. Phantoms 13 4.4. Device Holder 14 4.5. Scanning Procedure 14 4.6. Data Storage and Evaluation 15 4.7. Tissue Dielectric Parameters for Head and Body Phantoms 17 4.8. Tissue equivalent liquid properties 17 4.9. System Check 18 4.10. SAR measurement procedure 19 4.11. Power Reduction 26 5. T E S T C O N D I T I O N S A N D R E S U L T S 27 5.1. Conducted Power Results 27 5.2. Simultaneous TX SAR Considerations 31 5.3. SAR Measurement Results 34 5.4. SAR Measurement Variability 37 5.5. General description of test procedures 37 5.6. Measurement Uncertainty (300MHz-3GHz) 38 5.7. System Check Results 40 5.8. SAR Test Graph Results 46 6. C A L I B R A T I O N C E R T I F I CA T E 56 6.1. Probe Calibration Certificate 56 6.2. D835V2 Dipole Calibration Certificate 67 6.3. D1900V2 Dipole Calibration Certificate 75 6.4. D2450V2 Dipole Calibration Ceriticate 83 6.5. DAE4 Calibration Certificate 91 7. T E S T S E T U P P H O T O S 94 V1.0 Page 5 of 102 Report No.: CTL1412193074-SAR 8. E X T E R N A L P H O T O S O F T H E E U T 100 V1.0 Page 6 of 102 Report No.: CTL1412193074-SAR 1. T E S T S T A N D A R D S The tests were performed according to following standards: IEEE Std C95.1, 1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 KHz to 300 GHz. It specifies the maximum exposure limit of 1.6 W/kg as averaged over any 1 gram of tissue for portable devices being used within 20 cm of the user in the uncontrolled environment. IEEE Std 1528™-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wir…

Text truncated - open the document above for the full version.

V1.0 Page 72 of 102 Report No.: CTL1412193074-SAR V1.0 Page 73 of 102 Report No.: CTL1412193074-SAR V1.0 Page 74 of 102 Report No.: CTL1412193074-SAR V1.0 Page 75 of 102 Report No.: CTL1412193074-SAR 6.3. D1900V2 Dipole Calibration Certificate V1.0 Page 76 of 102 Report No.: CTL1412193074-SAR V1.0 Page 77 of 102 Report No.: CTL1412193074-SAR V1.0 Page 78 of 102 Report No.: CTL1412193074-SAR V1.0 Page 79 of 102 Report No.: CTL1412193074-SAR V1.0 Page 80 of 102 Report No.: CTL1412193074-SAR V1.0 Page 81 of 102 Report No.: CTL1412193074-SAR V1.0 Page 82 of 102 Report No.: CTL1412193074-SAR V1.0 Page 83 of 102 Report No.: CTL1412193074-SAR 6.4. D2450V2 Dipole Calibration Ceriticate V1.0 Page 84 of 102 Report No.: CTL1412193074-SAR V1.0 Page 85 of 102 Report No.: CTL1412193074-SAR V1.0 Page 86 of 102 Report No.: CTL1412193074-SAR V1.0 Page 87 of 102 Report No.: CTL1412193074-SAR V1.0 Page 88 of 102 Report No.: CTL1412193074-SAR V1.0 Page 89 of 102 Report No.: CTL1412193074-SAR V1.0 Page 90 of 102 Report No.: CTL1412193074-SAR V1.0 Page 91 of 102 Report No.: CTL1412193074-SAR 6.5. DAE4 Calibration Certificate V1.0 Page 92 of 102 Report No.: CTL1412193074-SAR V1.0 Page 93 of 102 Report No.: CTL1412193074-SAR V1.0 Page 94 of 102 Report No.: CTL1412193074-SAR 7. T e s t S e t u p P h o t o s Photograph of the depth in the Head Phantom (850MHz) Photograph of the depth in the Body Phantom (850MHz) Photograph of the depth in the Head Phantom (1900MHz) V1.0 Page 95 of 102 Report No.: CTL1412193074-SAR Photograph of the depth in the Body Phantom (1900MHz) Photograph of the depth in the Head Phantom (2450MHz) Photograph of the depth in the Body Phantom (2450MHz) V1.0 Page 96 of 102 Report No.: CTL1412193074-SAR Right Head Tilt Setup Photo Right Head Cheek Setup Photo Left Head Tilt Setup Photo V1.0 Page 97 of 102 Report No.: CTL1412193074-SAR Left Head Cheek Setup Photo 10mm Body-worn Rear Side Setup Photo 10mm Body-worn Front Side Setup Photo V1.0 Page 98 of 102 Report No.: CTL1412193074-SAR 10mm Body-worn Left SideSetup Photo 10mm Body-worn Right Side Setup Photo 10mm Body-worn Top Side Setup Photo V1.0 Page 99 of 102 Report No.: CTL1412193074-SAR 10mm Body-worn Bottom Side Setup Photo V1.0 Page 100 of 102 Report No.: CTL1412193074-SAR 8. E x t e r n a l P h o t o s o f t h e EUT V1.0 Page 101 of 102 Report No.: CTL1412193074-SAR V1.0 Page 102 of 102 Report No.: CTL1412193074-SAR .....................End of Report.........................

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-26636041 TEST REPORT FCC Part 22 Subpart H / Part 24 Subpart E Report Reference No......................: CTL1412193074-WU Compiled by ( position+printed name+signature)..: File administrators Jacky Chen Name of the organization performing the tests ( position+printed name+signature)..: Test Engineer Tracy Qi Approved by ( position+printed name+signature)..: Manager Tracy Qi Date of issue.....................................: Jan. 20, 2015 Test Firm..........................................: Shenzhen CTL Testing Technology Co., Ltd. Address.............................................: Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 Applicant’s name............................: USA 111 INC. Address.............................................: 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Test specification: Standard ...........................................: FCC CFR Title 47 Part 2, Part 22H, Part 24E EIA/TIA 603-C: 2004 Master TRF.......................................: Dated 2011-01 Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : Mobile phone FCC ID.......................................: 2ADOV-IRULUU1PRO Trade Mark.......................................: iRULU Model/Type reference.......................: U1PRO GSM/WCDMA Transmit ...........................................: 2G:GSM 850: 824~849MHz, PCS 1900: 1850~1910MHz 3G:WCDMA Band II: 1850-1910MHz, WCDMA Band V: 824~849MHz Receive ............................................: 2G:GSM 850: 869~894MHz, PCS 1900: 1930~1990MHz 3G:WCDMA Band II: 1930~1990MHz, WCDMA Band V: 869~894MHz Release Version .............................: 2G:R99 3G:Rel-6 V1.0 Page 2 of 65 Report No.: CTL1412193074-WU Type of modulation...........................: 2G: GMSK for GSM/GPRS, EDGE only for downlink 3G: QPSK GPRS Type ......................................: Class B GPRS Class ...................................: Class 12 GPS work frequency ................................: 1575.42MHz Type of modulation ...........................: BPSK Bluetooth Work frequency................................: 2402~2480MHz Version..............................................: V3.0, V4.0 Type of modulation ...........................: FHSS Data Rate..........................................: 1Mbps(GFSK), 2Mbps(Pi/4 DQPSK), 3Mbps(8DPSK) Wi-Fi Work frequency ................................: 802.11b/g/n(20MHz): 2412~2462MHz, 802.11n(40MHz): 2422~2452MHz Type of modulation ...........................: 802.11b DSSS, 802.11g/n: OFDM Data Rate..........................................: 802.11b: 1/2/5.5/11 Mbps 802.11g: 6/9/12/18/24/36/48/54 Mbps 802.11n: up to 150 Mbps Antenna Gain ...................................: -2.0 dBi for GSM850 and WCDMA Band V -2.0 dBi for PCS1900 and WCDMA Band II -3.0 dBi for Bluetooth and Wi-Fi Antenna type ....................................: Internal Harware version ...............................: G807 J3 V1.3 Software version ...............................: G807_J3_ZX_N2_U1PRO_1028 Result................................................: Positive V1.0 Page 3 of 65 Report No.: CTL1412193074-WU T E S T R E P O R T Test Report No. : CTL1412193074-WU Jan. 20, 2015 ______________________________________________________________________________________________ Date of issue Equipment under Test : Mobile phone Model /Type : U1PRO Applicant : USA111 INC. Address : 5885 Green Pointe Dr. Suite B Groveport OH, 43125 Manufacturer Shenzhen Allland Networking Co., Ltd. Address Fourth Floor, #B Building, Weiyulong Industrial Park, Xuegang North Road #16, Bantian Street, Longgang District, Shenzhen, China Test Result according to the standards on page 5: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. V1.0 Page 4 of 65 Report No.: CTL1412193074-WU Contents 1 . TEST STANDARDS.......................................................................5 2 . SUMMARY...................................................................................6 2.1. General Remarks .........................................................................................................................................6 2.2. Equipment Under Test ................................................................................................................................6 2.3. Short description of the Equipment under Test (EUT) ............................................................................6 2.4. EUT operation mode ...................................................................................................................................6 2.5. EUT configuration .......................................................................................................................................6 2.6. Related Submittal(s) / Grant (s)..................................................................................................................7 2.7. Modifications ...............................................................................................................................................7 3 . TEST ENVIRONMENT ....................................................................8 3.1. Address of the test laboratory .........................................................................................................…

Text truncated - open the document above for the full version.

Test Setup Photos of the EUT