2ADQM-KMC50Weather-Resistant Gauge-Style Media Center with Bluetooth

KMC MEDIA CENTER Owner’s Manual KMC50 KMC MULTI-MEDIA RECEIVER WITH USB, BLUETOOTH and AUX Input. 2 KMC50 Owner’s Manual Media Center Multi-Media Receiver w/ USB, Bluetooth and AUX Input Thank you for purchasing the KMC50 Media Center. We recommend read- ing through the entire manual for detailed instructions on how to install and operate the unit. For support please call: 1-800-844-2774 Purchase Date: Serial Number: ITEMS INCLUDED: (1) KMC50 (1) Trim Ring (1) Wiring Harness (1) UV Cover (1) Mounting Gasket (1) Owner’s Manual FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide more reasonable protection against harmful interference in a residential installation. Operation is subjected to the following two conditions: (1) This device may not cause harmful interference, and (2) the device must accept any interference re- ceived, including interference that may cause undesired operation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, you are encouraged to try to correct the interference by one of the following measures: t
3FPSJFOU
PS
SFMPDBUF
UIF
SFDFJWJOH
BOUFOOB t
*ODSFBTF
UIF
TFQBSBUJPO
CFUXFFO
UIF
FRVJQNFOU
BOE
SFDFJWFS t
$POOFDU
UIF
FRVJQNFOU
JOUP
BO
PVUMFU
PO
B
DJSDVJU
EJGGFSFOU
GSPN
UIBU
UP
XIJDI
UIF
receiver is connected. t
$POTVMU
UIF
EFBMFS
PS
BO
FYQFSJFODFE
SBEJP57
UFDIOJDJBO
GPS
IFMQ $IBOHFT
PS
NPEJýDBUJPOT
OPU
FYQSFTTMZ
BQQSPWFE
CZ
UIF
QBSUZ
SFTQPOTJCMF
GPS
DPNQMJ- ance could void the user’s authority to operate the equipment. The equipment should be installed and operated with minimum distance 20cm between the radiator & your body. CE Operation temperature: (-25°C~55°C ) Bluetooth: 2402-2480MHz Bluetooth transmitter power: 3.01dBm Hereby declares that this equipment is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. All radio frequencies can be used in all EU member safe without restrictions. 3 KMC50 Installation Overview 3” Hole Cutout Main Harness 1- Red, Switched 12V+ 2- White/Blk, Left Front Spkr, Negative 3- White, Left Front Spkr, Positive 4- Orange, Dimmer 5- Grey/Blk, Right Front Spkr, Negative 6- Grey, Right Front Spkr, Positive 7- Blue, Amp Turn-on 8- Green/Blk, Left Rear Spkr, Negative 9- Green, Left Rear Spkr, Positive 10- Black, Ground 11- Purple/Blk, Right Rear Spkr, Negative 12- Purple, Right Rear Spkr, Positive 1 2 3 4 5 6 7 8 9 1. Main Harness 2. USB Port 3. Antenna Input 4. Remote Port 5. AUX Input 6. Front RCA Output 7. Rear RCA Output 8. Sub RCA Output 9. Zone 2 RCA Output 5.5” 3.5” en 4 OPERATION The button layout below will give you a quick overview of the button functionality. BUTTONS: 1 - Source 2 - Favorites 3 - Menu 4 - Sub/Zone 2 5 - Seek/Tune Down 6 - Play/Pause 7 - Seek/Tune Up 8 - Volume Knob Function: How To: Power On Press the Source (1) button. Power Off Hold the Source (1) button for 2 seconds. Volume Up Turn the knob (8) clockwise. Volume Down Turn the knob (8) counter-clockwise. Seek Up Press Seek Up (7) once. Seek Down Press Seek Down (5) once. Tune Up Hold down Seek Up (7). Tune Down Hold down Seek Down (5). Enter/Select Press the Knob (8) inward once. Play/Pause Press Play/Pause (6) once. Mute Press Play/Pause (6) once. Subwoofer Level Press Sub/Zone (4) once. Zone 2 Level Hold Sub/Zone (4) for 1 second. 1 2 3 84567 DISPLAY KMC50 Settings MENU To enter the Settings Menu : Hold the MENU (3) button for 2 seconds. Press the Menu (3) button to scroll between menu items and rotate the knob (7) to adjust the Menu setting. Available Settings are: Beep: Turns the audible key press on and off. Default is off. Loud: Turns the loudness function on and off. Default is off. Area: Changes the FM/AM Tuner region from USA to Europe. Default is USA. Zone 2: Turns Zone 2 volume control on and off. Default is off. Z2VOL: The Absolute and Relative setting for Zone 2 change the behavior of the Zone 2 volume control with regard to the main zone volume. a. Relative- When the main zone volume is increased or decreased, Zone 2 volume will adjust up or down accordingly. b. Absolute- When the main zone volume is increased or decreased, Zone 2 volume will remain at the same level until adjusted independently. HPF: Adjusts the high-pass crossover for internal channels and Front, Rear, Zone 2 RCA outputs. Your available options: OFF, 50Hz, 80Hz, 120Hz. Dimmer: The Dimmer allows you to adjust the brightness of the screen, and buttons. You can adjust the brightness from 0 to 10. 5 OPERATION SourcesSources Cont. To change any of the sources, press the Source (1) button on the KMC50. FM Source: AM Source: Weatherband (WX) Source: Function: How To: Seek Up: Press the Seek Up (7) button once. Seek Down: Press the Seek Down (5) button once. Tune Up: Hold the Tune Up (7) button for 2 seconds. Then press (7) once. Tune Down: Hold the Tune Down (5) button for 2 seconds. Then press (5) once. Mute: Press the Play/Pause (6) button. Function: How To: Seek Up: Press the Seek Up (7) button once. Seek Down: Press the Seek Down (5) button once. Tune Up: Hold the Tune Up (7) button for 2 seconds. Then press (7) once. Tune Down: Hold the Tune Down (5) button for 2 seconds. Then press (5) once. Mute: Press the Play/Pause (6) button. Function: How To: Seek Up: Press the Seek Up (7) button once. Seek Down: Press the Seek Down (5) button once. Tune Up: Hold the Tune Up (7) button for 2 seconds. Then press (7) once. Tune Down: Hold the Tune Down (5) button for 2 seconds. Then press (5) once. Mute: Press the Play/Paus…

Text truncated - open the document above for the full version.

Report No.: W EXHIBI EUT View 1 EUT View 2 WTX19X100 T 2 - EUT 1 2 74947W-1 T EXTER RNAL PH HOTOGR APHS Mo FCC P odel: KMC50 Part 15.247 Report No.: W EUT View 3 EUT View 4 WTX19X100 3 4 74947W-1 Mo FCC P odel: KMC50 Part 15.247 Report No.: W EUT View 5 EUT View 6 WTX19X100 5 6 74947W-1 Mo FCC P odel: KMC50 Part 15.247 Report No.: W EUT View 7 WTX19X100 7 74947W-1 Mo FCC P odel: KMC50 Part 15.247

Report No.: W EXHIBI Proposed Specificatio n silk-screened Proposed WTX19X100 T 1 - PRO FCC ID La ns: Text is b d onto the EU Label Loca 74947W-1 ODUCT L abel Forma FCC ID: This device Operation i (1) This de (2) this dev including i black in colo UT or shall be ation on EU LABELIN at 2ADQM-K e complies w is subject to t evice may not vice must acc nterference th r and justifie e affixed at a UT FCC NG KMC50 with Part 15 of the following t cause harmf cept any inter hat may caus ed. Labels ar conspicuous ID Label Lo f the FCC Ru g two conditio ful interferenc ference receiv e undesired o re printed in location on t cation ules. ons: ce, and ved, operation. indelible ink the EUT. Mo FCC P k on perman odel: KMC50 Part 15.247 nent adhesivee

Report No.: W EXHIBI EUT Housi n Solder Boa r WTX19X100 T 3 - EUT ng and Boar rd-Compone 74947W-1 T INTER rd View 1 ent View 1 NAL PHO OTOGRA APHS Mo FCC P odel: KMC50 Part 15.247 Report No.: W Solder Boa r Solder Boa r WTX19X100 rd-Compone rd-Compone 74947W-1 ent View 2 ent View 3 Mo FCC P odel: KMC50 Part 15.247 Report No.: W Solder Boa r Solder Boa r WTX19X100 rd-Compone rd-Compone 74947W-1 ent View 4 ent View 5 Mo FCC P odel: KMC50 Part 15.247 Report No.: W Solder Boa r Solder Boa r WTX19X100 rd-Compone rd-Compone 74947W-1 ent View 6 ent View 7 Mo FCC P odel: KMC50 Part 15.247 Report No.: W Solder Boa r Solder Boa r WTX19X100 rd-Compone rd-Compone 74947W-1 ent View 8 ent View 9 Mo FCC P odel: KMC50 Part 15.247 Report No.: W Antenna V i BT Ant WTX19X100 iew tenna 74947W-1 Mo FCC P odel: KMC50 Part 15.247

1. MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 General Information Client Information Applicant: CPS Distributors, Inc. Address of applicant: 6024 Parretta Dr. Kansas City, MO 64120, USA Manufacturer: Shenzhen Tokwa Precision Technology Co., Ltd Address of manufacturer: A5 Building,Tongxin Industry District, No. 87, Tongxin Road, Baolong Street, Longgang District, Shenzhen, Guangdong, China General Description of EUT: Product Name: Weather-Resistant Gauge-Style Media Center with Bluetooth Brand Name: Kicker Model No.: KMC50 Adding Model(s): KMC4 Rated Voltage: DC 12V Battery Capacity: / Power Adapter: / FCC ID: 2ADQM-KMC50 Technical Characteristics of EUT: Bluetooth Bluetooth Version: V2.1 (BDR/EDR mode) Frequency Range: 2402-2480MHz RF Output Power: 2.026dBm (Conducted) Data Rate: 1Mbps, 2Mbps, 3Mbps Modulation: GFSK, Pi/4 DQPSK, 8DPSK Quantity of Channels: 79 Channel Separation: 1MHz Type of Antenna: Integral Antenna Antenna Gain: -3.0dBi 1.2 Standard Applicable According to §1.1307(b)(1) and KDB 447498 D01 General RF Exposure Guidance v06, system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. (a) Limits for Occupational / Controlled Exposure Frequency range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times | E | 2 , | H | 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 / / F/300 6 1500-100000 / / 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times | E | 2 , | H | 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 / / F/1500 30 1500-100000 / / 1 30 Note: f = frequency in MHz: * = Plane-wave equivalents power density 1.3 MPE Calculation Method S = (30*P*G) / (377*R 2 ) S = power density (in appropriate units, e.g., mw/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mw) G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor is normally numeric gain. R = distance to the center of radiation of the antenna (in appropriate units, e.g., cm) 1.4 MPE Calculation Result Maximum Tune-Up output power: 3(dBm) Maximum peak output power at antenna input terminal: 2.000 (mW) Prediction distance: >20(cm) Prediction frequency: 2480(MHz) Antenna gain: -3 (dBi) Directional gain (numeric gain): 0.50 The worst case is power density at prediction frequency at 20cm: 0.0002(mw/cm 2 ) MPE limit for general population exposure at prediction frequency: 1 (mw/cm 2 ) Result: Pass

Model: KMC50 Report No.: WTX19X10074947W-1 Page 1 of 58 FCC Part 15.247 FCC Part 15C Measurement and Test Report For CPS Distributors, Inc. 6024 Parretta Dr. Kansas City, MO 64120, USA FCC ID: 2ADQM-KMC50 FCC Rule(s): FCC Part 15.247 Product Description: Weather-Resistant Gauge-Style Media Center with Bluetooth Tested Model: KMC50 Report No.: WTX19X10074947W-1 Sample Receipt Date: Oct.30, 2019 Tested Date: Oct.30, 2019 to May.13, 2020 Issued Date: May.13, 2020 Tested By: Jack Huang / Engineer Reviewed By: Lion Cai / RF Manager Approved & Authorized By: Silin Chen / Manager Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Waltek Testing Group (Shenzhen) Co., Ltd. Model: KMC50 Report No.: WTX19X10074947W-1 Page 2 of 58 FCC Part 15.247 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 11 3. RF EXPOSURE ....................................................................................................................................................... 12 3.1 STANDARD APPLICABLE ....................................................................................................................................... 12 3.2 TEST RESULT........................................................................................................................................................ 12 4. ANTENNA REQUIREMENT ................................................................................................................................ 13 4.1 STANDARD APPLICABLE ....................................................................................................................................... 13 4.2 EVALUATION INFORMATION ................................................................................................................................ 13 5. FREQUENCY HOPPING SYSTEM REQUIREMENTS ................................................................................... 14 5.1 STANDARD APPLICABLE ....................................................................................................................................... 14 5.2 FREQUENCY HOPPING SYSTEM............................................................................................................................. 14 5.3 EUT PSEUDORANDOM FREQUENCY HOPPING SEQUENCE .................................................................................... 15 6. QUANTITY OF HOPPING CHANNELS AND CHANNEL SEPARATION ................................................... 16 6.1 STANDARD APPLICABLE ....................................................................................................................................... 16 6.2 TEST PROCEDURE ................................................................................................................................................. 16 6.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 16 7. DWELL TIME OF HOPPING CHANNEL .......................................................................................................... 20 7.1 STANDARD APPLICABLE ....................................................................................................................................... 20 7.2 TEST PROCEDURE ................................................................................................................................................. 20 7.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 21 8. 20DB BANDWIDTH ............................................................................................................................................... 28 8.1 STANDARD APPLICABLE ....................................................................................................................................... 28 8.2 TEST PROCEDURE ................................................................................................................................................. 28 8.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 29 9. RF OUTPUT POWER ...........…

Text truncated - open the document above for the full version.

Report No.: W EXHIBI Radiation E Radiation E WTX19X100 T 4 - TES Emission Tes Emission Tes 74947W-1 ST SETUP st Setup (Belo st Setup (30M P PHOTO ow 30MHz) MHz to 1GHz OGRAPH z) HS Mo FCC P odel: KMC50 Part 15.247 Report No.: W Radiation E Radiation E WTX19X100 Emission Tes Emission Tes 74947W-1 st Setup (1GH st Setup (Abo Hz to 18GHz ove 18GHz) z) Mo FCC P odel: KMC50 Part 15.247