2ADTD-D0212020Dual-tech Detector

1 Disassembling the Detector 2 The Printed Circuit Board（PCB） 3 45 Installation Hints 6 The 12 m Lens 7 Resistor Wiring 8 Choose the Connection Type 9 Powering up 10 11 Dimension and Weight (a) Lens(b) LED Light Pipe (c) Lens Holder (e) Nut (d) PCB (f) Casing Screw DS-PDD12-EG2 12 m Pet Immune Dual-Tech Detector (g) Alarm Resistor Headers 1K, 2K2, 4K7, 5K6, 6K8 (a) PIR Sensor (f) Terminals (h) Tamper Spring (e) Tamper Resisitor Headers 1K,2K2, 4K7,5K6 1 1 2 2 3 3 (1) Ceiling Bracket Fitting (Non EN compliant) (2) Wall Bracket Fitting (2) Single End of Line Wiring(1) Normally Closed(3) Double End of Line Wiring 99 g (3.5 oz) 1 2 3 4 The detector has two method for resistor wiring: (1) Using headers to select the End of Line resistance (Control panel dependent) on the ALARM/TAMPER header pins. (2) Select an resistance (Control panel dependent), and add the resistor to ALARM/TAMPER wiring ports of the detector. Note: If EOL (End of Line) wiring is not used, leave the headers OFF. If the headers and the header pins does not match, do not force the header, please select the method 2 to wire the resistor. Method 1 and method 2 should not be used on the ALARM/TAMPER at the same time. Technical Specification 85.9° (a) Detection Range (b) Mounting Height 52 zones 4 planes Mounting height range from 1.8 m to 2.4 m. The recommended mounting height is 2.2 m. = = (a) Alarm Resistance (b) Tamper Resistance 1K, 2K2, 4K7, 5K6, 6K8 1K, 2K2, 4K7, 5K6 ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info UD17437B IC Information CLASS B: CAN ICES-3 (B)/NMB-3(B) Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not ins talled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase …

Text truncated - open the document above for the full version.

Hangzhou Hikvision Digital Technology Co., Ltd. Date: 2020-07-02 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ADTD-D0212020 To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Xiuying Zhang Title: Senior Certification engineer Signature: On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +86-0571-88075998-62460

Hangzhou Hikvision Digital Technology Co., Ltd. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, angzhou 310052, China Regarding: Confidentiality Request regarding application for FCC ID: 2ADTD-D0212020 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature: Printed Name (on file with the FCC associated with the Grantee Code): Xiuying Zhang Title: Senior Certification engineer Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Hangzhou Hikvision Digital Technology Co., Ltd. Address No. 555 Qianmo Road, Binjiang District Hangzhou 310052, China Grantee Code 2ADTD FCC ID 2ADTD-D0212020 Authorized Contact Name Xiuying Zhang Contact Email [email protected] Contact Phone +86-571-88075998 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:2020/7/2 Print Name: Xiuying Zhang Title: Senior Certification engineer *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Page: 1 / 6 Report No.: T200519D09 Rev.: 00 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT Page: 2 / 6 Report No.: T200519D09 Rev.: 00 Page: 3 / 6 Report No.: T200519D09 Rev.: 00

Label location FCC Warning

Page: 4 / 6 Report No.: T200519D09 Rev.: 00 INTERNAL PHOTOGRAPHS OF EUT Page: 5 / 6 Report No.: T200519D09 Rev.: 00 Page: 6 / 6 Report No.: T200519D09 Rev.: 00 Antenna RF IC & Crystal

FCC ID: 2ADTD-D0212020 ISED No.: 20199- D0212020 Page: 1 / 49 Report No.: T200519D09-RP Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-210 Test Standard FCC Part 15.249 IC RSS-210 issue 10 and IC RSS-GEN issue 5 Trade name HIKVISION Product name Dual-tech Detector Model No. DS-PDD12-EG2, DS-PDD12P-EG2UHK, DS-PDD12P-EG2UVS, DS-PDD12P-EG2HUN, DS-PDD12-EG2CKV, DS-PDD12-EG2KVO, DS-PDD12-EG2UHK , DS-PDD12P-EG2CKV, DS-PDD12P-EG2KVO,DS-PDD12P-EG2, DS-PDD12-EG2UVS, DS-PDD12-EG2HUN Test Result Pass The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory) Approved by: Kevin Tsai Deputy Manager Page: 2 / 49 Report No.: T200519D09-RP Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 June 29, 2020 Initial Issue ALL Angel Cheng 01 July 24, 2020 1. Revised section 1.1. 2. Revised section 1.2. 3. Revised section 1.6. 4. Revised section 4.2. 5. Revised section 4.3. 6. Revised setup photo test report number. P.4, P.5, P.7, P.17~19, P.23~32, A-1~A-8 Angel Cheng Page: 3 / 49 Report No.: T200519D09-RP Rev.: 01 Table of contents 1. GENERAL INFORMATION .................................................................................................. 4 1.1 EUT INFORMATION ............................................................................................................ 4 1.2 EUT CHANNEL INFORMATION .......................................................................................... 5 1.3 ANTENNA INFORMATION .................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ....................................................................................... 6 1.5 FACILITIES AND TEST LOCATION .................................................................................... 7 1.6 INSTRUMENT CALIBRATION ............................................................................................. 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ........................................................... 9 2. TEST SUMMERY ............................................................................................................... 10 3. DESCRIPTION OF TEST MODES ..................................................................................... 11 3.1 THE WORST MODE OF MEASUREMENT ........................................................................ 11 4. TEST RESULT ................................................................................................................... 12 4.1 AC POWER LINE CONDUCTED EMISSION ..................................................................... 12 4.2 20dB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) .............................................. 17 4.3 FIELD STRENGTH OF FUNDAMENTAL AND RADIATION SPURIOUS EMISSION ........ 20 APPENDIX 1 - PHOTOGRAPHS OF EUT Page: 4 / 49 Report No.: T200519D09-RP Rev.: 01 1. GENERAL INFORMATION 1.1 EUT INFORMATION FCC Applicant Hangzhou Hikvision Digital Technology No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China IC Applicant No. 555 Qianmo Road, Binjiang District Hangzhou 310052 China (Peoples Republic Of) FCC Manufacturer Shanghai Kohler Electronics., Ltd. No. 1955, Fengxiang Road, Baoshan Area, Shanghai, PRC Post code: 200444 IC Manufacturer No. 555 Qianmo Road, Binjiang District Hangzhou 310052 China (Peoples Republic Of) Equipment Dual-tech Detector Model Name DS-PDD12-EG2, DS-PDD12P-EG2UHK, DS-PDD12P-EG2UVS, DS-PDD12P-EG2HUN, DS-PDD12-EG2CKV, DS-PDD12-EG2KVO, DS-PDD12-EG2UHK , DS-PDD12P-EG2CKV, DS-PDD12P-EG2KVO,DS-PDD12P-EG2, DS-PDD12-EG2UVS, DS-PDD12-EG2HUN Model Discrepancy Difference of the model numbers (list on this report) are just for marketing purpose only. Trade Name HIKVISION EUT Functions 24G Radar Received Date May 19, 2020 Date of Test May 25 ~ June 18, 2020 Output Power 24.1925GHz Peak : 94.81dBuV/m @1m Average : 94.26dBuV/m @1m 24.2125GHz Peak : 98.78dBuV/m @1m Average : 98.53dBuV/m @1m Power Operation . Hardware Version RPCB700E Software Version V1.0.0 SN A12S6A298 DC 12V by Adapt…

Text truncated - open the document above for the full version.

Page: A-1 / A-8 Report No.: T200519D09-RP Rev.: 01 APPENDIX-1 Test Photo 24.1925GHz Radiation (Below 1GHz) Page: A-2 / A-8 Report No.: T200519D09-RP Rev.: 01 Radiation (1GHz ~ 40GHz) Page: A-3 / A-8 Report No.: T200519D09-RP Rev.: 01 Radiation (40GHz ~ 50GHz) Radiation (50GHz ~ 75GHz) Page: A-4 / A-8 Report No.: T200519D09-RP Rev.: 01 Radiation (75GHz ~ 90GHz) Radiation (90GHz ~ 100GHz) Page: A-5 / A-8 Report No.: T200519D09-RP Rev.: 01 24.2125GHz Radiation (Below 1GHz) Page: A-6 / A-8 Report No.: T200519D09-RP Rev.: 01 Radiation (1GHz ~ 40GHz) Page: A-7 / A-8 Report No.: T200519D09-RP Rev.: 01 Radiation (40GHz ~ 50GHz) Radiation (50GHz ~ 75GHz) Page: A-8 / A-8 Report No.: T200519D09-RP Rev.: 01 Radiation (75GHz ~ 90GHz) Radiation (90GHz ~ 100GHz)