2ADTD-R010201113Wireless Repeater

2 1 2 1 2 2 2 4 2 3 3 Wireless Repeater Quick Start Guide 1 2 4 ENGLISH APPEARANCE ENROLLMENT 1. Fault Indicator 4. Tamper Switch5. Power Switch6. Serial Port INSTALLATION Specification 2. Signal Strength Indicator3. Power Indicator 7. Power Interface 1 4 5 6 7 2 3 xxxx Device I. Check siganl strength. II. Install the device. a. Route the cable through the bottom cable hole or knock-out cable hole. b. Mount the device. Signal Strength Test III a b Tamper-Proof1, Front and Back Auto ParingSupported PIRCAM ParingSupported Power Switch1 RF methodTwo way communication RF Modulation2GFSK RF Frequency 433.1 MHz and 433.7MHz Wireless SecurityAES-128 Power supply100VAC to 240VAC Battery typeBuilt in Lithium Battery Battery life spanUp to 35 hours LEDs Status3, Register/Signal (Green/Red), Power (Green), Fault (Amber) Operation temperature﹣10°C~+55°C Operation humidity10％~90％ Shell materialPlastic Dimension(WxHxD)150*150*25mm Weight372g ColorWhite Installation methodWall Mounting FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the se paration between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation 1 2 3 ESPAÑOL ASPECTO REGISTRO 1. Indicador de fallo 4. Interruptor antimanipulación 5. Interruptor de alimentación6. Puerto serie INSTALACIÓN I. Comprobar la intensidad de la señal. II. Instalar el dispositivo. a. Haga pasar el cable a través del orificio de la parte inferior o por el orificio pre-perforado a tal efecto. b. Monte el dispositivo. Especificación 2. Indicador de fuerza de señal3. Indicador de alimentación 7. Conexión de alimentación Antimanipulación1, Delante y detrás Emparejamiento automáticoCompatible Interruptor de alimentación1 Método de RFComunicación bidireccional Frecuencia de RF 433.1 MHz and 433.7MHz Fuente de alimentaciónde 100 a 240 VCA Tipo de bateríaBatería de litio integrada Duración de la bateríaHasta 35 horas Estados del led3, registro/señal (verde/rojo), encendido (verde), fallo (ámbar) Temperatura de funcionamiento -10 °C ~ +55 °C Humedad de funcionamiento10% ~ 90% Material de la carcasaPlástico Dimensiones (An × Al × F)150×150×25 mm Peso372 g Colorblanco Método de instalaciónMontaje en la pared 1 2 3 PORTUGUÊS APRESENTAÇÃO REGISTRO 1. Indicador de falha 4. Chave de violação5. Interruptor6. Porta serial INSTALAÇÃO I. Verifique a intensidade do sinal. II. Instale o dispositivo. a. Passe o cabo pelo orifício de cabo inferior ou pelo orifício do passa-cabos. b. Monte o dispositivo. Especificações 2. Indicador de intensidade do sinal 3. Indicador de energia 7. Entrada de alimentação Antiviolação1, Frente e verso Pareamento automáticoSuportado Interruptor1 Método de RFComunicação bidirecional Frequência de RF 433.1 MHz and 433.7MHz Fonte de alimentação100 VCA a 240 VCA Tipo de pilhaBateria de lítio integrada Vida útil das bateriasAté 35 horas Status dos LEDs 3, registrar/sinal (verde/vermelho), energia (verde), falha (âmbar) Temperatura de operação -10 °C a +55 °C Umidade de operação10% a 90% Material do invólucroPlástico Dimensões (L x A x P)150 mm x 150 mm x 25 mm Peso372 g Corbranco Método de instalaçãoMontagem na parede About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the company website. Trademarks Acknowledgement Trademarks and logos mentioned are the properties of their respective owners. LEGAL DISCLAIMER TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. OUR COMPANY MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL OUR COMPANY BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF OUR COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AN…

Text truncated - open the document above for the full version.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Hangzhou Hikvision Digital Technology Co., Ltd. Address No. 555 Qianmo Road, Binjiang District Hangzhou 310052, China Grantee Code 2ADTD FCC ID 2ADTD-R010201113 Authorized Contact Name Xiuying Zhang Contact Email [email protected] Contact Phone +86-571-88075998 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:2020/10/15 Print Name: Xiuying Zhang Title: Senior Certification engineer *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Hangzhou Hikvision Digital Technology Co., Ltd. Date: 2020-10-15 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ADTD-R010201113 To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Xiuying Zhang Title: Senior Certification engineer Signature: On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +86-0571-88075998-62460

Hangzhou Hikvision Digital Technology Co., Ltd. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, angzhou 310052, China Regarding: Confidentiality Request regarding application for FCC ID: 2ADTD-R010201113 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature: Printed Name (on file with the FCC associated with the Grantee Code): Xiuying Zhang Title: Senior Certification engineer Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.

Hangzhou Hikvision Digital Technology Co., Ltd. Current Date : 2020-10-15 To: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products *WE (Hangzhou Hikvision Digital Technology Co., Ltd.) HEREBY DECLARED THAT Product Description Wireless Repeater Model No. DS-PR1-WBUHK, DS-PR1-WBCKV, DS-PR1-WBUVS, DS-PR1-WBKVO, DS-PR1-WBHUN Manufacturer’s Name Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturer’s Address No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China *Except that the model number and appearance deviation, are identical with the original product as follows: Note: The definition of identical should be “electrically identical”. A device will be considered to be electrically identical if no changes are made to the devices’ schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical. Model No. (型号): DS-PR1-WB Manufacturer’s Name (生产商名称): Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturer’s Address（生产商商地址): No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Sincerely, Signature (签字): Printed Name (姓名): Xiuying Zhang Position/Title (职位): Senior Certification engineer Contact Number (联系电话): +86-571-88075998

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 4 Page 1 of 4 External Photos Applicant: Hangzhou Hikvision Digital Technology Co., Ltd. Address of Applicant: No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Equipment Under Test (EUT): Product Name: Wireless Repeater Model No.: DS-PR1-WB SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 4 Page 2 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 4 Page 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 4 of 4 Page 4 of 4 End

Label location FCC warning

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 6 Page 1 of 6 Internal Photos Applicant: Hangzhou Hikvision Digital Technology Co., Ltd. Address of Applicant: No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Equipment Under Test (EUT): Product Name: Wireless Repeater Model No.: DS-PR1-WB SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 6 Page 2 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 6 Page 3 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 4 of 6 Page 4 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 5 of 6 Page 5 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 6 of 6 Page 6 of 6 E EE En nn nd dd d

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM200900773101 Page: 1 of 25 Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. TEST REPORT Application No.: SHEM2009007731CR FCC ID: 2ADTD-R010201113 Applicant: Hangzhou Hikvision Digital Technology Co., Ltd. Address of Applicant: No.555 Qianmo Road,Binjiang District Hangzhou 310052,China Manufacturer: Hangzhou Hikvision Digital Technology Co., Ltd. Address of Manufacturer: No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Factory: Hangzhou Hikvision Electronics Co., Ltd. Address of Factory: No.299,Qiushi Road,Tonglu Economic Development Zone,Tonglu County, Hangzhou,Zhejiang,310052,China Equipment Under Test (EUT): EUT Name: Wireless Repeater Model No.: DS-PR1-WB,DS-PR1-WBUHK,DS-PR1-WBCKV,DS-PR1-WBUVS,DS-PR1- WBKVO,DS-PR1-WBHUN¤ ¤ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Standard(s) : 47 CFR Part 15, Subpart C 15.231 Date of Receipt: 2020-09-10 Date of Test: 2020-09-12 to 2020-10-09 Date of Issue: 2020-10-12 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM200900773101 Page: 2 of 25 Revision Record Version Description Date Remark 00 Original 2020-10-12 / Authorized for issue by: Micheal Niu / Project Engineer Parlam Zhan / Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM200900773101 Page: 3 of 25 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.231 N/A 47 CFR Part 15, Subpart C 15.203 Pass N/A: Not applicable Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emission Part 15.207 ANSI C63.10 (2013) Section 6.2 N/A Pass 20dB Bandwidth 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.231(c) Pass Dwell Time (15.231(a)) 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.231(a) Pass Field Strength of the Fundamental Signal (15.231(b)) 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.5 N/A Pass Radiated Emissions 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.4&6.5&6.6 N/A Pass N/A: Not applicable Note: Declaration of EUT Family Grouping: Note: There are series models mentioned in this report, and they are the similar in electrical and electronic characters. Only the model DS-PR1-WB was tested since their differences were the model number and appearance. SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM200900773101 Page: 4 of 25 3 Contents Page 1 COVER PAGE ........................................................................................................................................ 1 2 TEST SUMMARY .................................................................................................................................. 3 3 CONTENTS ........................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................... 5 4.1 DETAILS OF E.U.T. .......................................................................................................................... 5 4.2 DESCRIPTION OF SUPPORT UNITS ..................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY........................................................................................................... 5 4.4 TEST LOCATION ............................................................................................................................... 6 4.5 TEST FACILITY ................................................................................................................................. 6 4.6 DEVIATION FROM STANDARDS ........................................................................................................... 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS................................................................................... 6 5 EQUIPMENT LIST ................................................................................................................................. 7 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 8 6.1 ANTENNA REQUIREMENT .................................................................................................................. 8 7 RADIO SPECTRUM MATTER TEST RESULTS .................................................................................... 9 7.1 CONDUCTED EMISSIONS AT AC POWER LINE (150KHZ-30MHZ) ........................................................... 9 7.2 20DB BANDWIDTH ..........................................................................................................................13 7.3 DWELL TIME ...................................................................................................................................15 7.4 SPURIOUS EMISSIONS ..............................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 4 Page 1 of 4 Test Setup Photos-FCC Applicant: Hangzhou Hikvision Digital Technology Co., Ltd. Address of Applicant: No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Equipment Under Test (EUT): Product Name: Wireless Repeater Model No.: DS-PR1-WB SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 4 Page 2 of 4 1 Contents Page 1 CONTENTS............................................................................................................... 2 2 EQUIPMENT UNDER TEST PICTURES ............................................................. 3 2.1 Conducted Emissions at AC Power Line (150kHz-30MHz) Test Setup ......... 3 2.2 Spurious emissions ........................................................................................... 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 4 Page 3 of 4 2 EQUIPMENT UNDER TEST PICTURES 2.1 Conducted Emissions at AC Power Line (150kHz-30MHz) Test Setup 2.2 Spurious emissions 30MHz-1GHz SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 4 of 4 Page 4 of 4 Above 1GHz Zoom: End