2ADVA-X10MT87TABLET PC

USER MANUAL ENGLISH MANUAL Tablet PC Introduction To avoid failure of device, battery and charger, please prevent the device, battery, charger of all over heating or too cold circumstance Announcements Preventive maintainance Please always keep the MID dry. To avoid the device short trouble, corrosion fault and electric short, please prevent the device, battery and charger from water and moisture, and don’t operate the device or charger by wet hand. To avoid failure of device, battery and charger, please prevent the device, battery, charger from violent shock or shake. Never shock, throw, prod the MID, or drop, extrude, bend the MID. Never disassemble the device and accessories arbitrarily, otherwise the device and accessories are not in our company warranty scope. Safety Instruction Before the operation of the MID, please read this chapter and teach your kids about these information. For further details, please refer to the safety instructions and announcement. Never use the MID when driving car, in order to ensure safe driving. In the medical area, please abide by related rules and regulations. Please shut down the MID when it is near to the medical area. To avoid the wireless signal to interrupt the plane- controlled signal, please shut down the MID or using airplane mode when you are boarding a flight, 1 To avoid electronic equipment failure, please shut down the MID in the vicinage of high-accuracy electronic equipments. Please don’t disassemble the MID and accessories. Only authorized agent has access to service the MID. Please keep the MID far away from magnetic equipments, the radiation of MID may erase the data stored in the magnetic equipments. Never use the MID in the vicinage of high temperature, inflammable gas ( gas station). Protect the MID and accessories from kids reach scope, and avoid the kids to use the MID without parents’ supervision. Please comply with related rules and regulations, and respect others’ privacy and legal rights while using the MID. Please strictly adhere to related instructions in the manual when using USB cable to ensure the safety of the MID or PC. Never use the MID in bathroom or other humid environment, and please protect the MID from liquid wash or wet. 2 Unit at a Glance 1. POWER 2. VOL+ / VOL- 3. RESET 4. HEADPHONE 5. SIM / Micro SD Card slot 6. USB 7.FRONT CAMERA 8. REAR CAMERA 9. FLASHING LIGHT 10. SPEAKER 3 8 123 4 5 7 6 10 10 9 4 Charge the battery Before using the device for the first time, you must charge the battery. 1. You can charge the device with a travel adapter or by connecting the device to a PC with a USB cable. 2. Battery full icon is shown when finished if your device is off. Warning：Use only original batteries and chargers. Unapproved chargers or cables can cause batteries to explode or damage your device. Install the SIM card You need to insert a SIM card to use the Phone function when the tablet turning off. To install the SIM card, follow the instructions below. 1.Make sure that the card's gold contacts face into the device. 2.Push the SIM card into the slot until it clicks when it turning off. Install the memory card To store additional multimedia files, you need insert a memory card when it turning off. 1.Insert a memory card with the gold contacts facing downwards. 2.Push the memory card into the slot until it clicks, when it turning off. Notice: Our company uses approved industry standards for memory cards, but some brands may not be fully compatible with your device. 5 Getting started Turn your device on and off To turn on your device, press and hold the power key. To turn off your device, press and hold the power key, and then tap OK. Switch to flight mode To use only your device's non-network services, switch to flight mode. Please follow the instructions below to turn on flight mode: Tap Settings--WIRELESS & NETWORKS--More--Airplane mode --Turn on/off Home screen The home screen has multiple panels. Scroll left or right to the panels on the home screen, you can view indicator icons, widgets, shortcuts to applications, and other items. 123 4 Task bar The task bar is shown at the bottom of the screen. It displays commonly used option buttons, battery level indicator, current time and other indicator icons. 1. Return to previous screen. 2. Return to home screen. 3. View the applications you have accessed recently. 4. Display notification icons. Tap the notifications area to open the notification panel. 6 Indicator icons Icon Definition Icon Definition Open Wi-Fi available Flight mode activated Wi-Fi connected New email Signal strength New text or multimedia message Roaming mode Call in progress Uploading data Missed call Downloading data Call on hold Connected to PC Call diverting activated Alarm activated Battery power level Music being played 7 Phone To use calling functions, tap Phone from application list. Press to show the dial numbers, and to make the call. Ringtone & Vibrate You can set different ringtones for incoming calls. Select SettingsSound & notification General Phone ringtone to open a list of ringtones, select the desired ringtone, and then select OK to confirm. Turn on Vibrate to create a checkmark and the tablet vibrates to notify you of incoming calls Connectivity USB Connection You can connect your device to a PC by a micro USB cable and use it as a removable disk, which allows you access the file directory. Wi-Fi With Wi-Fi, you can connect to the internet or other network devices anywhere an access point or wireless hotspot is available. Activate the Wi-Fi feature 1. Select Settings Wi-Fi, 2.Turn on the Wi-Fi button, and select a network. Web Browser Tap Browser from application list to access to the web. Browser webpages Communication 1.Select Browser to launch a specified homepage. 2.To access a specific webpage, select the URL input field, enter the web address of the webpage, and select Go. 3.To zoom in, place two fingers on the screen and spread them apart. To zoom out, move your fingers cl…

Text truncated - open the document above for the full version.

QA-FR-170-B XTRATECH COMPUTERS S.A. Add: Ciudadela Profesor Aguirre Abad,solar 40, manzana 118 Guayaquil Ecuador Tel: 0755-86265237 Fax: 0755-86265237 Email:[email protected] FCC Authorization Date: 2021-01-19 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , XTRATECH COMPUTERS S.A. .Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Jeff Sun Title: Manager

QA-FR-171-A XTRATECH COMPUTERS S.A. Add: Ciudadela Profesor Aguirre Abad,solar 40, manzana 118 Guayaquil Ecuador Tel: 0755‐86265237 Fax: 0755‐86265237 Email:[email protected] FCC Confidential Authorization Date: 2021-01-19 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2ADVA-X10MT87 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, XTRATECH COMPUTERS S.A. hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description  Parts List/Tune up procedure (for licensed devices) The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Jeff Sun Title: Manager

XTRATECH COMPUTERS S.A. Add: Ciudadela Profesor Aguirre Abad,solar 40, manzana 118 Guayaquil Ecuador Tel: 0755-86265237 Fax: 0755-86265237 Email:[email protected] DECLARATION OF SIMILARITY Date: 2021-01-19 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We, XTRATECH COMPUTERS S.A., hereby declare that the product: TABLET PC, FCC ID: 2ADVA-X10MT87, model: M16Q3M, X10MT87 is electrically identical with the model: M16Q3M-4G which was tested by BACL with the same electromagnetic emissions and electromagnetic compatibility characteristics. A description of the differences between those models and that are declared similar are as follows: They are the same product, and just the different model name, the rest are the same. Please contact me should there be need for any additional clarification or information. Best Regards, Signature: Printed Name: Jeff Sun Title: Manager

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS LTE AUX Antenna BT&Wifi Antenna WWAN Main Antenna Chip1 Chip2

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “*”. SAR EVALUATION REPORT For XTRATECH COMPUTERS S.A. Ciudadela Profesor Aguirre Abad,solar 40, manzana 118 Guayaquil Ecuador FCC ID: 2ADVA-X10MT87 Report Type: Original Report Product Type: TABLET PC Report Number: RDG200824010-20 Report Date: 2021-01-13 Reviewed By: Brave Lu SAR Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Dongguan) No.12, Pulong East 1 st Road, Tangxia Town, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG200824010-20 SAR Evaluation Report 2 of 57 Attestation of Test Results EUT Information EUT Description TABLET PC Tested Model M16Q3M-4G Multiple Models M16Q3M,X10MT87 FCC ID 2ADVA-X10MT87 Serial Number RDG200824010-SA-S1 Test Date 2020/12/22 ~ 2020/12/23 MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) GSM 850 1g Body SAR 0.77 1. 6 PCS 1900 1g Body SAR 0.67 WCDMA Band 2 1g Body SAR 0.71 WCDMA Band 5 1g Body SAR 0.48 LTE Band 2 1g Body SAR 0.77 LTE Band 4 1g Body SAR 0.96 WLAN 2.4G 1g Body SAR 0.07 Simultaneous 1g Body SAR 1.09 1g Body SAR 1.03(Hotspot) Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices RF Exposure Procedures: TCB Workshop April 2019 IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-1:2016 Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 941225 D01 3G SAR Procedures v03r01 KDB 941225 D05 SAR for LTE Devices v02r05 KDB 616217 D04 SAR for laptop and tablets v01r02 KDB 248227 D01 802 11 Wi-Fi SAR v02r02 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG200824010-20 SAR Evaluation Report 3 of 57 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ............................................................................................................................ 4 EUT DESCRIPTION ........................................................................................................................................................ 5 TECHNICAL SPECIFICATION............................................................................................................................................. 5 REFERENCE, STANDARDS, AND GUIDELINES .................................................................................................... 6 SAR LIMITS ..................................................................................................................................................................... 7 FACILITIES ...................................................................................................................................................................... 8 DESCRIPTION OF TEST SYSTEM ............................................................................................................................. 9 5, IN THIS CASE, IEC PARAMETERS APPLIED.EQUIPMENT LIST AND CALIBRATION ........................... 14 EQUIPMENT LIST AND CALIBRATION ................................................................................................................ 15 EQUIPMENTS LIST & CALIBRATION INFORMATION ...................................................................................................... 15 SAR MEASUREMENT SYSTEM VERIFICATION ................................................................................................ 16 LIQUID VERIFICATION ................................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION .............................................................................................................................. 18 SAR SYSTEM VALIDATION DATA ........................................................................................................................ 19 EUT TEST STRATEGY AND METHODOLOGY .................................................................................................... 23 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR ......................................................................... 23 CHEEK/TOUCH POSITION .............................................................................................................................................. 24 EAR/TILT POSITION ....................................................................................................................................................... 24 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS .......................................................................…

Text truncated - open the document above for the full version.

APPENDIX C PROBE CALIBRATION CERTIFICATES DIPOLE CALIBRATION CERTIFICATES

Report No.: RDG200824010-20 Page 1 of 27 Plot 1#: GSM 850_Body Back_Mid DUT: TABLET PC; Type: M16Q3M-4G; Serial: RDG200824010-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 836.6 MHz;Duty Cycle: 1:2 Medium parameters used: f = 836.6 MHz; σ = 0.902 S/m; ε r = 41.524; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration: • Probe: EX3DV4 - SN7329; ConvF(10.13, 10.13, 10.13) @ 836.6 MHz; Calibrated: 2020/11/30 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn772; Calibrated: 2020/11/23 • Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.36 W/kg Zoom Scan (6x6x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.745 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 2.04 W/kg SAR(1 g) = 0.756 W/kg; SAR(10 g) = 0.378 W/kg Maximum value of SAR (measured) = 0.804 W/kg 0 dB = 0.804 W/kg = -0.95 dBW/kg Report No.: RDG200824010-20 Page 2 of 27 Plot 2#: GSM 850_Body Right_Mid DUT: TABLET PC; Type: M16Q3M-4G; Serial: RDG200824010-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 836.6 MHz;Duty Cycle: 1:2 Medium parameters used: f = 836.6 MHz; σ = 0.902 S/m; ε r = 41.524; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration: • Probe: EX3DV4 - SN7329; ConvF(10.13, 10.13, 10.13) @ 836.6 MHz; Calibrated: 2020/11/30 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn772; Calibrated: 2020/11/23 • Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (41x141x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.284 W/kg Zoom Scan (6x7x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.426 V/m; Power Drift = -0.13 dB Peak SAR (extrapolated) = 0.292 W/kg SAR(1 g) = 0.122 W/kg; SAR(10 g) = 0.065 W/kg Maximum value of SAR (measured) = 0.142 W/kg 0 dB = 0.142 W/kg = -8.48 dBW/kg Report No.: RDG200824010-20 Page 3 of 27 Plot 3#: GSM 850_Body Top_Mid DUT: TABLET PC; Type: M16Q3M-4G; Serial: RDG200824010-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 836.6 MHz;Duty Cycle: 1:2 Medium parameters used: f = 836.6 MHz; σ = 0.902 S/m; ε r = 41.524; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration: • Probe: EX3DV4 - SN7329; ConvF(10.13, 10.13, 10.13) @ 836.6 MHz; Calibrated: 2020/11/30 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn772; Calibrated: 2020/11/23 • Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (51x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.537 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 7.226 V/m; Power Drift = -0.13 dB Peak SAR (extrapolated) = 1.13 W/kg SAR(1 g) = 0.295 W/kg; SAR(10 g) = 0.110 W/kg Maximum value of SAR (measured) = 0.624 W/kg 0 dB = 0.624 W/kg = -2.05 dBW/kg Report No.: RDG200824010-20 Page 4 of 27 Plot 4#: PCS 1900_Body Back_Mid DUT: TABLET PC; Type: M16Q3M-4G; Serial: RDG200824010-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 1880 MHz;Duty Cycle: 1:2 Medium parameters used: f = 1880 MHz; σ = 1.401 S/m; ε r = 40.037; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration: • Probe: EX3DV4 - SN7329; ConvF(8.14, 8.14, 8.14) @ 1880 MHz; Calibrated: 2020/11/30 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn772; Calibrated: 2020/11/23 • Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (91x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.21 W/kg Zoom Scan (6x6x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 3.809 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 2.00 W/kg SAR(1 g) = 0.648 W/kg; SAR(10 g) = 0.291 W/kg Maximum value of SAR (measured) = 1.31 W/kg 0 dB = 1.31 W/kg = 1.17 dBW/kg Report No.: RDG200824010-20 Page 5 of 27 Plot 5#: PCS 1900_Body Right_Mid DUT: TABLET PC; Type: M16Q3M-4G; Serial: RDG200824010-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 1880 MHz;Duty Cycle: 1:2 Medium parameters used: f = 1880 MHz; σ = 1.401 S/m; ε r = 40.037; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration: • Probe: EX3DV4 - SN7329; ConvF(8.14, 8.14, 8.14) @ 1880 MHz; Calibrated: 2020/11/30 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn772; Calibrated: 2020/11/23 • Phantom: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (41x141x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.128 W/kg Zoom Scan (6x6x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.522 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 0.375 W/kg SAR(1 g) = 0.151 W/kg; SAR(10 g) = 0.072 W/kg Maximum value of SAR (measured) = 0.149 W/kg 0 dB = 0.149 W/kg = -8.27 dBW/kg Report No.: RDG200824010-20 Page 6 of 27 Plot 6#: PCS 1900_Body Top_Mid DUT: TABLET PC; Type: M16Q3M-4G; Serial: RDG200824010-SA-S1 Communication System: Generic GPRS-4 slots; Frequency: 1880 MHz;Duty Cycle: 1:2 Medium parameters used: f = 1880 MHz; σ = 1.401 S/m; ε r = 40.037; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration: • Probe: EX3DV4 - SN7329; ConvF(8.14, 8.14, 8.14) @ 1880 MHz; Calibrated: 2020/11/30 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Elect…

Text truncated - open the document above for the full version.

Report No.: RDG200824010-20 Page 1 of 3 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm Phantom Type: SAM (30deg probe tilt) with CRP v5.0_20150321; Type: QD000P40CD; Serial: TP:1874 Report No.: RDG200824010-20 Page 2 of 3 Body Back Setup Photo (0mm) Body Right Setup Photo (0mm) Report No.: RDG200824010-20 Page 3 of 3 Body Top Setup Photo (0mm)

FCC PART 15.247 TEST REPORT For XTRATECH COMPUTERS S.A. Ciudadela Profesor Aguirre Abad,solar 40, manzana 118 Guayaquil Ecuador Report Type: Original Report Product Name: TABLET PC Report Number: RDG200824010-00B Re port Date: 2020-12-16 Reviewed By: Ivan Cao Assistant Manager Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.12, Pulong East 1 st Road, Tangxia Town, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn FCC ID: 2ADVA-X10MT87 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG200824010-00B Page 2 of 64 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 DECLARATIONS ............................................................................................................................................................ 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 SUPPORT CABLE LIST AND DETAILS .......................................................................................................................... 10 BLOCK DIAGRAM OF TEST SETUP .............................................................................................................................. 11 SUMMARY OF TEST RESULTS ............................................................................................................................. 12 FCC §15.247 (i) & §1.1310 & §2.1093- RF EXPOSURE .......................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 FCC §15.203 - ANTENNA REQUIREMENT ........................................................................................................... 14 APPLICABLE STANDARD ............................................................................................................................................ 14 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 14 FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS ..................................................................................... 15 APPLICABLE STANDARD ............................................................................................................................................ 15 EUT SETUP ................................................................................................................................................................ 15 EMI TEST RECEIVER SETUP ....................................................................................................................................... 15 TEST PROCEDURE ...................................................................................................................................................... 16 CORRECTED AMPLITUDE & MARGIN CALCULATION ................................................................................................. 16 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 16 TEST DATA ................................................................................................................................................................ 17 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS ............................................................................. 19 APPLICABLE STANDARD ............................................................................................................................................ 19 EUT SETUP ................................................................................................................................................................ 19 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP .............................................................................................. 20 TEST PROCEDURE ...................................................................................................................................................... 20 CORRECTED AMPLITUDE & MARGIN CALCULATION ................................................................................................. 20 TEST EQUIPMENT LIST AND DETAILS ......................................................................................................................... 21 TEST DATA ......…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emission -front View Conducted Emission -Side View Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View