2ADYY-BG6Mobile Phone

SPARK Go 2024 User Manual Explosion diagram specification 1 FL(CTP+LCM) 2 REC DECO 3 F HSG ASM 4 F FLASH HOOD 5 PS LENS 6 R CAM 8W AD 7 F CAM 8 R CAM 13M 9 R CAM 8W 10 PCBA MB 11 PS RUBBER 12 SIM CARD HOLDER 13 PCBA COPPER D 14 MI HOUSING 15 SCREW L3.5 16 BAT COVER ASM 17 R FLASHHOOD 18 R CAM DECO 13M 19 R FLASH LENS 20 R CAM 13M LENS 21 REC 22 RF CABLE 23 BATTERY 24 MOTOR LINEA 25 PCBA SUB 26 PCBA COPPER B 27 EARPHONE RUBBER 28 SPK 29 USB RUBBER 30 PCBA COPPER A 31 SIDE KEY 32 SPK CON CLOTH 33 SCREW L3.2 34 R CAM 13M CON FOAM 35 FP MYLAR 36 FP 37 R FLASH DECO 38 R CAM 8W DECO 39 R CAM 8W LENS Know your phone 1. Front camera 2. Volume + key 3. Volume - key 4. Power key & side fingerprint sensor SIM/SD card installation 1. Power off mobile. 2. Refer to the following picture for SIM / SD card installation. Charging the phone You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty. FCC Caution Labelling requirements. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Information to user. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information: This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: BG6(FCC ID:2ADYY-BG6) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.23 W/kg and when properly worn on the body is 0.74 W/kg. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. HiOS runs on Android TM OS. Android is a trademark of Google LLC.

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: 86-755-61803856 E-mail: [email protected] CFR 47 §2.911(d)(5)(i) Attestation Letter Attestation Letter Date: 2023-08-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: 2ADYY-BG6 TECNO MOBILE LIMITED certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature Yiting Luo Project Manager TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: 86-755-61803856 E-mail: [email protected] CFR 47 §2.911 (d)(5)(ii) Attestation Letter Attestation Letter Date: 2023-08-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: 2ADYY-BG6 TECNO MOBILE LIMITED certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Yiting Luo Project Manager TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG

U.S. AGENT LETTER OF ATTESTATION Date: 2023-08-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2ADYY-BG6 certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19- 25 SHAN MEI STREET FOTAN NT HONGKONG FRN: 0024206328 Email: [email protected] Signed by (printed name): Yiting Luo Signature: TECNO MOBILE LIMITED TECNO MOBILE LIMITED Tel: +86-0755-61803856

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: +86-0755-61803856 E-mail: [email protected] QA-FR-170-B FCC Authorization Date: 2023-08-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, TECNO MOBILE LIMITED hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature Yiting Luo Project Manager

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: +86-0755-61803856 E-mail: [email protected] FCC Confidential Authorization Date: 2023-08-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2ADYY-BG6 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, TECNO MOBILE LIMITED hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description • Software Security Description • Part list/Tune up Procedure (for licensed device) As well as short-term confidential treatment of information accompanying this application for a period of 180 days after grant is issued as outlined below: • Internal Photos • User’s Manual • External Photos • Test Set-up Photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Yiting Luo Project Manager

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-EXP Page 1 of 5 EUT EXTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-EXP Page 2 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-EXP Page 3 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-EXP Page 4 of 5 adapter China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-EXP Page 5 of 5

Label Label location

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 1 of 11 EUT INTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 2 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 3 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 4 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 5 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 6 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 7 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 8 of 11 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 9 of 11 AUX antenna China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 10 of 11 2.4Gwifi+BT+BLE+5G wifi +2+3+4G antenna China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-INP Page 11 of 11 battery

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-00B Page 60 of 62 5. RF EXPOSURE EVALUATION 5.1 Applicable Standard According to§15.247(i) and §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB447498 D01 General RF Exposure Guidance v06: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 5.2 Measurement Result The max conducted power including tune-up tolerance is 7.5 dBm (5.62 mW). [(max. power of channel, mW)/(min. test separation distance, mm)][√f(GHz)] =5.62/5*(√2.480) = 1.8< 3.0 Result: Compliant. The stand-alone SAR evaluation is not necessary.

Fea ※ ※ ※ A p ※G Zhej Ltd S Add Area ature High gain Omani-dir e Wide bandw pplication GSM850/90 LTE B1/ B Name and iang Haitong c Shanghai Bran ：1F，Buildin a，Shanghai ectional width n 0/DCS/PCS B2/B3/B4/B d address of th communicatio nch ng C5，No.255 S/WCDMA B5/B7/B8/B he antenna ma on electronic L 55 Xiupu Roa AB1/B2/B4/B 12/B17/B20 anufacturer Limited by Sha d，Pudong N B5/B8 0/B28/B38/ are ew /B40/B41/B Model num 3IN DIV MA 5G W B66 ber of the ante N1: BG6-ANT V: BG6-ANT IN: BG6-AN WIFI: BG6-A enna T1 T2 T3 NT4 A Transmitte Receiver Antenna Gain er Frequency Frequency ANT3 ANT1 ANT4 y G G DCS G G 4 GSM 850/W GSM 900/W S /WCDMA PCS/WC WCDM L L L LTE GSM 850/W GSM 900/W DCS/L WCDM PCS/WC WCDM L L L LTE GSM 85 GSM 90 DCS /WC PCS/W WC L L 2.4 WCDMA B5 WCDMA B8 A B4/LTE B DMA B2/L MA B1/LTE LTE B7 :24 LTE B40 :2 LTE B38: 2 LTE B41: 2 LTE B20: E B12/B17/ WCDMA B5 WCDMA B8 LTE B3/B66 MA 4/LTE B DMA B2/L MA B1/LTE LTE B7 :26 LTE B40:2 LTE B38: 2 LTE B41: 2 LTE B20: E B12/B17/B 50/WCDMA 00/WCDMA CDMA B4/L WCDMA B CDMA B1/ LTE B7/B3 LTE B4 LTE B2 LTE B12/B1 4G Wi-Fi/B 5G Wi- 5/LTE B5: 8 8/LTE B8 : B3/B4/B66 : LTE B2:185 B1 : 1920 – 496-2565M 2300-2400M 2570-2620M 2535-2655M 832-862MH /B28:710-75 5/LTE B5: 8 8/LTE B8 : 6 : 1805–1 B4 : 2110-2 LTE B2:193 B1 : 2110 – 620-2690M 300-2400M 2570-2620M 2535-2655M 791-821MH B28 :758-80 A B5/LTE B A B8/LTE B LTE B3/B4/ B2/LTE B2: /LTE B1: -1 8/B41: -0.2 40: -0.8dBi 20: -6.4dBi 17/B28: -6.2 Bluetooth:-3 Fi: -0.9dBi 824–849 M 880–915 M 1710–178 50-1910MH – 1980MHz MHz MHz MHz MHz Hz 55MHz 869–894 M 925–960 M 1880 MHz 2155 MHz 30-1990MH – 2170MHz MHz MHz MHz MHz Hz 03MHz B5: -5.0dBi B8: -5.2dBi /B66: -1.4dB : -1.3dBi 1.4dBi 2dBi 2dBi 3.1dBi MHz MHz 85 MHz Hz z MHz MHz Hz z i i Bi ※ AN T Antenna Ga T1 2.4GWIF ain FI&BT 2.4G 2.4G W WIFI&BT WIFI&BT Phi=0deg Phi=90deg ※ AN T Main Antenna Ga T3 n Antenna ain GSM 2.4G W M850 / WCDM WIFI&BT T MA B5 / LTE Theta=90deg E B5/B20 PPhi=0deg GSM GSM M850 / WCDM 850 / WCDM MA B5 / LTE MA B5 / LTE B B5/B20 Ph B5/B20 Th hi=90deg heta=90deg ※ Main Antenna Ga n Antenna ain L L LTE B40 Phi= LTE B40 Phi= =0deg =90deg ※ Main Antenna Ga n Antenna ain LT GSM900 / W TE B40 Theta= WCDMA B8 / L =90deg LTE B8 Phi=0deg G G GSM900 / WC GSM900 / WC CDMA B8 / L CDMA B8 / LT LTE B8 Phi=9 TE B8 Theta= 90deg =90deg ※ Main Antenna Ga n Antenna D ain DCS1800/PC DCS1800/PCS CS1900/WCD S1900/WCDM DMA B1/B2LT MA B1/B2LT TE B1/B2/B3/ TE B1/B2/B3/B /B4/B66Phi=0 B4/B66 Phi=9 0deg 90deg ※ Main D Antenna Ga n Antenna DCS1800/PCS ain S1900/WCDM LTE MA B1/B2LTE E B7/B38/41 P E B1/B2/B3/B Phi=0deg B4/B66Theta= =90deg LTE LTE B E B7/B38/41 P B7/B38/41 Th Phi=90deg heta=90deg ※ Main Antenna Ga n Antenna ain LTE B1 LTE B 12/B17/ B28 B12/B17/B28 Phi=0deg Phi=90deg ※ AN T Antenna Ga T4 ain LTE B 5G B12/B7/B28 T G WIFI Ph heta=90deg hi=0deg 5G 5G W G WIFI Phi WIFI Thet i=90deg ta=90deg Ant PRE tenna Photo EPARED BY : Y CHE Yu ECKEDBY uehua.sun YAPPROOVAL BY S.R DA .NO ATE: 2023/07/014

TEST REPORT Applicant: TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG FCC ID: 2ADYY-BG6 Product Name: Mobile Phone Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230847505-00B Date Of Issue: 2023/9/17 Reviewed By: Calvin Chen Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-00B Page 2 of 62 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-00B Page 3 of 62 CONTENTS TEST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY........................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 7 1.2.1 EUT Operation Condition: ............................................................................................................................. 7 1.2.2 Support Equipment List and Details .............................................................................................................. 7 1.2.3 Support Cable List and Details ...................................................................................................................... 7 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 8 1.3 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 2. SUMMARY OF TEST RESULTS .......................................................................................... 10 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 11 3.1.1 Applicable Standard ..................................................................................................................................... 11 3.1.2 EUT Setup .................................................................................................................................................... 12 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 12 3.1.4 Test Procedure ............................................................................................................................................. 13 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 13 3.2 RADIATED SPURIOUS EMISSIONS ...................................................................................................... 14 3.2.1 Applicable Standard ..................................................................................................................................... 14 3.2.2 EUT Setup .................................................................................................................................................... 14 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 15 3.2.4 Test Procedure ............................................................................................................................................. 15 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 15 3.3 20 DB EMISSION BANDWIDTH ..............................................................................…

Text truncated - open the document above for the full version.

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-00B-TSP TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View China Certification ICT Co., Ltd (Dongguan) Report No.: CR230847505-00B-TSP Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View