2ADYY-BG6SMobile Phone

SPARK Go 2024 User Manual Explosion diagram specification 1 FL(CTP+LCM) 2 REC DECO 3 F HSG ASM 4 F FLASH HOOD 5 PS LENS 6 R CAM 8W AD 7 F CAM 8 R CAM 13M 9 R CAM 8W 10 PCBA MB 11 PS RUBBER 12 SIM CARD HOLDER 13 PCBA COPPER D 14 MI HOUSING 15 SCREW L3.5 16 BAT COVER ASM 17 R FLASHHOOD 18 R CAM DECO 13M 19 R FLASH LENS 20 R CAM 13M LENS 21 REC 22 RF CABLE 23 BATTERY 24 MOTOR LINEA 25 PCBA SUB 26 PCBA COPPER B 27 EARPHONE RUBBER 28 SPK 29 USB RUBBER 30 PCBA COPPER A 31 SIDE KEY 32 SPK CON CLOTH 33 SCREW L3.2 34 R CAM 13M CON FOAM 35 FP MYLAR 36 FP 37 R FLASH DECO 38 R CAM 8W DECO 39 R CAM 8W LENS Know your phone 1. Front camera 2. Volume + key 3. Volume - key 4. Power key & side fingerprint sensor SIM/SD card installation 1. Power off mobile. 2. Refer to the following picture for SIM / SD card installation. Charging the phone You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty. FCC Caution Labelling requirements. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. ( ( 2 2 ) ) T T h h i i s s d d e e v v i i c c e e m m u u s s t t a a c c c c e e p p t t a a n n y y i i n n t t e e r r f f e e r r e e n n c c e e r r e e c c e e i i v v e e d d , , i i n n c c l l u u d d i i n n g g i i n n t t e e r r f f e e r r e e n n c c e e t t h h a a t t m m a a y y c c a a u u s s e e u u n n d d e e s s i i r r e e d d o o p p e e r r a a t t i i o o Information to user. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information: This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types:BG6s (FCC ID:2ADYY-BG6S) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.13 W/kg and when properly worn on the body is 0.72 W/kg. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. HiOS runs on Android TM OS. Android is a trademark of Google LLC.

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: 86-755-61803856 E-mail: [email protected] CFR 47 §2.911(d)(5)(i) Attestation Letter Attestation Letter Date: 2023-10-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: 2ADYY-BG6S TECNO MOBILE LIMITED certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature Yiting Luo Project Manager TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: 86-755-61803856 E-mail: [email protected] CFR 47 §2.911 (d)(5)(ii) Attestation Letter Attestation Letter Date: 2023-10-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: 2ADYY-BG6S TECNO MOBILE LIMITED certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Yiting Luo Project Manager TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG

U.S. AGENT LETTER OF ATTESTATION Date: 2023-10-24 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2ADYY-BG6S TECNO MOBILE LIMITED certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. TECNO MOBILE LIMITED accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19- 25 SHAN MEI STREET FOTAN NT HONGKONG FRN: 0024206328 Tel: Email: [email protected] Signed by (printed name): Yiting Luo Signature: +86-0755-61803856

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: +86-0755-61803856 E-mail: [email protected] QA-FR-170-B FCC Authorization Date: 2023-10-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, TECNO MOBILE LIMITED hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature Yiting Luo Project Manager

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: +86-0755-61803856 E-mail: [email protected] FCC Confidential Authorization Date: 2023-10-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2ADYY-BG6S In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, TECNO MOBILE LIMITED hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description • Software Security Description • Part list/Tune up Procedure (for licensed device) As well as short-term confidential treatment of information accompanying this application for a period of 180 days after grant is issued as outlined below: • Internal Photos • User’s Manual • External Photos • Test Set-up Photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Yiting Luo Project Manager

TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG Tel.: +86-0755-61803856 E-mail: [email protected] Date: 2023-10-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, The Main chip, model: UMS9230 installed in our product Mobile Phone, model: BG6s, FCC ID: 2ADYY-BG6S, this chip supports LTE function, but for marketing purpose, this chip only supports LTE Band 2/4/5/7/12/13/17/26/38/40/41(2535-2655MHz)/66, not support other LTE bands. The other LTE bands was disabled to use by manufacture in the software, the end user has no capability to activate it. The RF chip, model: UMW2631 installed in our product Mobile Phone, model: BG6s, FCC ID: 2ADYY-BG6S, supports 5G Wi-Fi function, but for marketing purpose, this chip only supports 5G Wi-Fi(5150-5250 MHz; 5725-5850 MHz). The 5G Wi-Fi (5250-5350 MHz, 5470-5725 MHz) was disabled to use by manufacture in the software, the end user has no capability to activate it. Signature: Yiting Luo Project Manager

China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-EXP EUT EXTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-EXP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-EXP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-EXP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-EXP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-EXP

China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP EUT INTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP Antenna China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-INP

APPENDIX C CALIBRATION CERTIFICATES DIPOLE CALIBRATION CERTIFICATES

Report No.: CR231058425-20 Page 1 of 6 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm Phantom Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 Report No.: CR231058425-20 Page 2 of 6 Head Left Cheek Setup Photo (0mm) Head Left Tilt Setup Photo (0mm) Report No.: CR231058425-20 Page 3 of 6 Head Right Cheek Setup Photo (0mm) Head Right Tilt Setup Photo (0mm) Report No.: CR231058425-20 Page 4 of 6 Body Front Setup Photo (10mm) Body (Worn) Back Setup Photo (10mm) 10mm 10mm Report No.: CR231058425-20 Page 5 of 6 Body Left Setup Photo (10mm) Body Right Setup Photo (10mm) 10mm 10mm Report No.: CR231058425-20 Page 6 of 6 Body Top Setup Photo (10mm) 10mm

Report No.: CR231058425-20 Page 1 of 229 Test Plot 1#: GSM 850_Low_Head Left Cheek DUT: Mobile Phone; Type: BG6s; Serial: 2BYR-4 Communication System: Generic GSM; Frequency: 824.2 MHz;Duty Cycle: 1:8 Medium parameters used: f = 824.2 MHz; σ = 0.91 S/m; ε r = 43.569; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration: • Probe: EX3DV4 - SN7522; ConvF(9.9, 9.9, 9.9) @ 824.2 MHz; Calibrated: 2023/5/29 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1354; Calibrated: 2022/10/31 • Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.631 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 27.86 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 1.01 W/kg SAR(1 g) = 0.655 W/kg; SAR(10 g) = 0.443 W/kg Maximum value of SAR (measured) = 0.695 W/kg 0 dB = 0.695 W/kg = -1.58 dBW/kg Report No.: CR231058425-20 Page 2 of 229 Test Plot 2#: GSM 850_Mid_Head Left Cheek DUT: Mobile Phone; Type: BG6s; Serial: 2BYR-4 Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.914 S/m; ε r = 43.438; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration: • Probe: EX3DV4 - SN7522; ConvF(9.9, 9.9, 9.9) @ 836.6 MHz; Calibrated: 2023/5/29 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1354; Calibrated: 2022/10/31 • Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.881 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 29.82 V/m; Power Drift = -0.14 dB Peak SAR (extrapolated) = 1.24 W/kg SAR(1 g) = 0.827 W/kg; SAR(10 g) = 0.550 W/kg Maximum value of SAR (measured) = 0.874 W/kg 0 dB = 0.874 W/kg = -0.58 dBW/kg Report No.: CR231058425-20 Page 3 of 229 Test Plot 3#: GSM 850_High_Head Left Cheek DUT: Mobile Phone; Type: BG6s; Serial: 2BYR-4 Communication System: Generic GSM; Frequency: 848.8 MHz;Duty Cycle: 1:8 Medium parameters used: f = 848.8 MHz; σ = 0.949 S/m; ε r = 43.208; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration: • Probe: EX3DV4 - SN7522; ConvF(9.9, 9.9, 9.9) @ 848.8 MHz; Calibrated: 2023/5/29 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1354; Calibrated: 2022/10/31 • Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.882 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 20.81 V/m; Power Drift = 0.11 dB Peak SAR (extrapolated) = 4.01 W/kg SAR(1 g) = 1.07 W/kg; SAR(10 g) = 0.462 W/kg Maximum value of SAR (measured) = 1.07 W/kg 0 dB = 1.07 W/kg = 0.29 dBW/kg Report No.: CR231058425-20 Page 4 of 229 Test Plot 4#: GSM 850_Mid_Head Left Tilt DUT: Mobile Phone; Type: BG6s; Serial: 2BYR-4 Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.914 S/m; ε r = 43.438; ρ = 1000 kg/m 3 Phantom section: Left Section DASY5 Configuration: • Probe: EX3DV4 - SN7522; ConvF(9.9, 9.9, 9.9) @ 836.6 MHz; Calibrated: 2023/5/29 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1354; Calibrated: 2022/10/31 • Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.687 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 29.15 V/m; Power Drift = -0.12 dB Peak SAR (extrapolated) = 1.12 W/kg SAR(1 g) = 0.683 W/kg; SAR(10 g) = 0.431 W/kg Maximum value of SAR (measured) = 0.715 W/kg 0 dB = 0.715 W/kg = -1.46 dBW/kg Report No.: CR231058425-20 Page 5 of 229 Test Plot 5#: GSM 850_Low_Head Right Cheek DUT: Mobile Phone; Type: BG6s; Serial: 2BYR-4 Communication System: Generic GSM; Frequency: 824.2 MHz;Duty Cycle: 1:8 Medium parameters used: f = 824.2 MHz; σ = 0.91 S/m; ε r = 43.569; ρ = 1000 kg/m 3 Phantom section: Right Section DASY5 Configuration: • Probe: EX3DV4 - SN7522; ConvF(9.9, 9.9, 9.9) @ 824.2 MHz; Calibrated: 2023/5/29 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1354; Calibrated: 2022/10/31 • Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.974 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 27.23 V/m; Power Drift = -0.15 dB Peak SAR (extrapolated) = 2.14 W/kg SAR(1 g) = 0.998 W/kg; SAR(10 g) = 0.580 W/kg Maximum value of SAR (measured) = 1.05 W/kg 0 dB = 1.05 W/kg = 0.21 dBW/kg Report No.: CR231058425-20 Page 6 of 229 Test Plot 6#: GSM 850_Mid_Head Right Cheek DUT: Mobile Phone; Type: BG6s; Serial: 2BYR-4 Communication System: Generic GSM; Frequency: 836.6 MHz;Duty Cycle: 1:8 Medium parameters used: f = 836.6 MHz; σ = 0.914 S/m; ε r = 43.438; ρ = 1000 kg/m 3 Phantom section: Right Section DASY5 Configuration: • Probe: EX3DV4 - SN7522; ConvF(9.9, 9.9, 9.9) @ 836.6 MHz; Calibrated: 2023/5/29 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1354; Calibrated: 2022/10/31 • Phantom: Twin SAM; Type: Twin SAM V5.0; Serial: TP:1470 • Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7470) Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.852 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8m…

Text truncated - open the document above for the full version.

Pro Mod S The abo China C Repo Da R Test Applica Add FCC oduct Nam del Numb Standard ove device ha Certification I ort Numb ate Of Iss Reviewed B T Laborato SA ant: TEC ress: FLA T SHAN ID: 2AD me: Mob ber: BG6 d(s): 47 C as been tested ICT Co., Ltd ber: CR2 sue: 2023 By: Kar Title: SAR ory: Chin No. 1 Guan Tel: + AR T CNO MO T N 16/F BL N MEI STRE DYY-BG6 bile Phon 6s CFR Part d and found d (Dongguan 23105842 3-11-03 rl Gong Engineer na Certifi 113, Pingkan ngdong, Chin +86-769-820 EST R OBILE LIM LOCK B UNI EET FOTAN 6S e 2(2.1093 ) compliant w n) 5-20 fication IC ng Road, Dala na 016888 REPO MITED IVERSAL IN N NT HONG ) with the requi CT Co., L ang Town, D ORT NDUSTRIA GKONG irement of th Ltd (Dong Dongguan, AL CENTRE he relative sta guan) 19-25 andards by China Certification ICT Co., Ltd (Dongguan) Report No.:CR231058425-20 Page 2 of 102 SAR TEST RESULTSSUMMARY Operation Frequency Bands Highest Reported 1g SAR (W/kg) Limits (W/kg) Head SAR Body SAR (Gap 10mm) GSM 850 1.09 0.36 1.6 PCS 1900 1.13 0.63 WCDMA Band 2 0.69 0.43 WCDMA Band 4 0.99 0.37 WCDMA Band 5 0.73 0.33 LTE Band 2 0.77 0.24 LTE Band 7 0.93 0.59 LTE Band 12&17 0.30 0.17 LTE Band 13 0.51 0.18 LTE Band 26&5 0.54 0.16 LTE Band 40A 0.39 0.23 LTE Band 40B 1.02 0.72 LTE Band 41&38 0.74 0.43 LTE Band 66&4 0.85 0.26 WLAN 2.4G 0.22 0.14 WLAN 5.2G 0.40 0.19 WLAN 5.8G 0.47 0.24 Maximum Simultaneous Transmission SAR Items Head SAR Body SAR (Gap 10mm) Hotspot (Gap 10mm) Limits Sum SAR(W/kg) 1.53 0.96 0.96 1.6 SPLSR NA NA NA 0.04 EUT Received Date: 2023/10/2 Tested Date: 2023/10/7~2023/10/15 Tested Result: Pass China Certification ICT Co., Ltd (Dongguan) Report No.:CR231058425-20 Page 3 of 102 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.:CR231058425-20 Page 4 of 102 CONTENTS DOCUMENT REVISION HISTORY .......................................................................................... 6 1. GENERAL INFORMATION .................................................................................................... 7 1.1 PRODUCT DESCRIPTION FOR DEVICE UNDER TEST (EUT) ............................................................... 7 1.2TEST SPECIFICATION, METHODS AND PROCEDURES ......................................................................... 8 1.3 SAR LIMITS .......................................................................................................................................... 9 2. SAR MEASUREMENTSYSTEM ........................................................................................... 10 3. EQUIPMENT LIST AND CALIBRATION .......................................................................... 17 3.1 EQUIPMENTS LIST & CALIBRATION INFORMATION ....................................................................... 17 4. SAR MEASUREMENT SYSTEM VERIFICATION ........................................................... 18 4.1 LIQUID VERIFICATION ...................................................................................................................... 18 4.2 SYSTEM ACCURACY VERIFICATION ................................................................................................. 21 4.3 SAR SYSTEM VALIDATION DATA ............................................................................................. 22 5. EUT TEST STRATEGY AND METHODOLOGY .............................................................. 31 5.1 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR ......................................... 31 5.2 CHEEK/TOUCH POSITION .................................................................................................................. 32 5.3 EAR/TILT POSITION ........................................................................................................................... 32 5.4 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS ................................................ 33 5.5 TEST DISTANCE FOR SAR EVALUATION .......................................................................................... 34 5.6 SAR EVALUATION PROCEDURE ....................................................................................................... 35 6. CONDUCTED OUTPUT POWER MEASUREMENT ........................................................ 36 6.1 DESCRIPTION OF TEST CONFIGURATION ......................................................................................... 37 6.2 MAXIMUM TARGET OUTPUT POWER ............................................................................................... 43 6.3 TEST RESULTS: .................................................................................................................................. 45 7. Sta…

Text truncated - open the document above for the full version.

Fea ※ ※ ※ Ap ※G LTE Zhej Ltd S Add Area ature High gain Omani-dir e Wide bandw pplication GSM850/90 E B1/B2/B3 Name and iang Haitong c Shanghai Bran ：1F，Buildin a，Shanghai ectional width n 0/DCS/PCS 3/B4/B5/B7 d address of th communicatio nch ng C5，No.255 SWCDMAB 7/B8/B12/B he antenna ma on electronic L 55 Xiupu Roa B1/B2/B4/B 13/B17/B26 anufacturer Limited by Sha d，Pudong N B5/B8 6/B28/B38/ are ew /B40/B41/B Model num 3IN DIV MA 5G W B66 ber of the ante N1: BG6-ANT V: BG6-ANT IN: BG6-AN WIFI: BG6-A enna T1 T2 T3 NT4 Rec An G Transmitte Frequency ceiver Frequ ntenna Gain A A A er y uency ANT3 ANT1 ANT4 GSM GSM DCS /WC PC W LT GSM GSM DCS//W PC W LT G G DC 850/WCD M 900/WCDM CDMA B4/ CS/WCDMA WCDMA B LTE LTE LTE LTE TE B12/B17 850/WCDM 900/WCDM WCDMA B WCDMA 4 CS/WCDMA WCDMA B LTE LTE LTE LTE TE B12/B17 GSM 850/W GSM 900/W S /WCDMA PCS/WCD WCDM LTE L L LTE B12/B 2.4G W 5 MA B5/LTE MA B8/LTE /LTE B3/B4 A B2/LTE B 1/LTE B1: E B7: 2496-2 B40: 2300- B38: 2570- B41: 2535- 7/B13/B28/ MA B5/LTE MA B8/LTE B4/LTE B3/B 4/LTE B4: 2 A B2/LTE B 1/LTE B1: E B7: 2620-2 B40: 2300- B38: 2570- B41: 2535- 7/B13/B28/B WCDMA B5 WCDMA B8 A B4/LTE B DMA B2/LT MA B1/LTE B7/B38/B4 LTE B40: -0 LTE B20:-6 B17/B13/B2 Wi-Fi/Blueto 5G Wi-Fi:-0 E B5: 824– E B8: 880– 4/B66: 1710 B2: 1850-19 1920 – 198 2565MHz -2400MHz -2620MHz -2655MHz /B26:710-75 E B5: 869– E B8: 925– B66: 1805– 2110-2155 M B2:1930-19 2110 – 217 2690MHz -2400MHz -2620MHz -2655MHz B26: 758-8 /LTE B5: -5 /LTE B8: -5 B3/B4/B66 TE B2: -1.3 E B1: -1.4dB 41: -0.2dBi 0.8dBi 6.4dBi 26/B28: -6.2 ooth: -3.1dB 0.9dBi –849 MHz –915 MHz 0–1785 MH 910MHz 0MHz 55MHz –894 MHz –960 MHz –1880 MH MHz 990MHz 0MHz 03MHz 5.0dBi 5.2dBi : -1.4dBi 3dBi Bi 2dBi Bi Hz z ※ ANT Antenna Ga T1 2.4G WI ain IFI&BT 2.4G 2.4G W WIFI&BT WIFI&BT Phi=0deg Phi=90deg ※ ANT Antenna Ga T3 Main Ante ain enna G 2.4G W GSM850 / WC WIFI&BT T CDMA B5 / LT Theta=90deg TE B5 Phii=0deg G G S SM850 / WCD SM850 / WCD DMA B5 / LT DMA B5 / LTE TE B5 Phi= E B5 Theta =90deg a=90deg ※ Main Antenna Ga n Antenna ain L L LTE B40 Phi= LTE B40 Phi= =0deg =90deg ※ Main Antenna Ga n Antenna ain LT GSM900 / W TE B40 Theta= WCDMA B8 / L =90deg LTE B8 Phi=0deg G G GSM900 / WC GSM900 / WC CDMA B8 / L CDMA B8 / LT LTE B8 Phi=9 TE B8 Theta= 90deg =90deg ※ Main Antenna Ga n Antenna D D ain DCS1800/PCS DCS1800/PCS S1900/WCDM S1900/WCDM MA B1/B2 L MA B1/B2LT LTE B1/B2/B3 TE B1/B2/B3/B 3/B4/B66 Phi= B4/B66 Phi=9 =0deg 90deg ※ Main D Antenna Ga n Antenna DCS1800/PCS ain 1900/WCDM LTE MA B1/B2LTE E B7/B38/41 P E B1/B2/B3/B Phi=0deg B4/B66 Theta= =90deg LTE LTE B E B7/B38/41 P B7/B38/41 Th Phi=90deg heta=90deg ※ Main Antenna Ga n Antenna ain LTEB12/B1 LTE B12/B 17/B13/B26/B B17/B13/B26/ B28 Phi=0d /B28 Phi=90d deg deg ※ ANT Antenna Ga T4 ain LTE B12/B 5 G 17/B13/B26/B G WIFI Ph B28 Theta=90 hi=0deg 0deg 5G 5G W G WIFI Phi WIFI Thet i=90deg ta=90deg Ant PRE tenna Photo EPARED BY : Y CHE Yu ECKEDBY uehua.sun YAPPROOVAL BY S.R DA .NO ATE: 2023/09/21

TEST REPORT A pplicant: TECNO MOBILE LIMITED Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG FCC ID: 2ADYY-BG6S Product Name: Mobile Phone Standard(s): 47 CFR Part 15, Subpart E(15.407) ANSI C63.10-2013 KDB 789033 D02 General U-NII Test Procedures New Rules v02r01 The above device has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR231058425-00D Date Of Issue: 2023/11/03 Reviewed By: Calvin Chen Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-00D Page 2 of 86 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR231058425-00D Page 3 of 86 CONTENTS DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION ......…

Text truncated - open the document above for the full version.