2AE66-KGE33Commentary Receiver

The KRUSEGO Multilingual System OPERATING INSTRUCTIONS PLEASE READ THIS IMPORTANT INFORMATION BEFORE USING THE KRUSEGO SYSTEM CHARGING THE KRUSEGO RECEIVERS When charging the KRUSEGO Receivers, ALWAYS ENSURE THE CASE IS OPEN. If the case lid is closed during recharging the air movement restriction will cause heat build-up and result in overheating and render the system unusable. Note: When charging, a red light glows in the headphone connector socket. When fully charged the red light goes out. KRUSEGO RECEIVERS When placing the KRUSEGO Receivers in and out of the recharger, they simply slot in with a VERY GENTLE push. Do not force the KRUSEGO Receivers into the recharger case as this will break the connectors in the base of the recharger case. If a connector breaks it cannot be replaced easily. THE KRUSEGO TOUR MASTER SETTING UP FOR EACH TOUR 1. Attach and lock the KRUSEGO Tour Master and suction mount to the vehicle windscreen by turning the levers on the base of the suction mount until they click and lock into place 2. Squeeze two of the vertical the X-GRIP levers to open the X-GRIP and insert the KRUSEGO Tour Master as demonstrated in the picture. Once released, the X-GRIP will hold the KRUSEGO Tour Master as shown in the bottom picture. 3. Turn on the KRUSEGO Tour Master using the ORANGE Power button at the bottom left of the keypad. The KRUSEGO Tour Master will now display “SYSTEM READY”. Push the BLUE “TOUR” Button. The display will now read “SELECT TOUR” with the default “NONE”. Push the ARROW UP button until the desired tour is reached. Press the PLAY/PAUSE Button and the display will now read “ON TOUR” for the selected tour. Shortly the screen will blink intermittently; this is “power save mode” to save battery power. 4. When the KRUSEGO Tour Master has obtained GPS lock, the GPS Icon at the top right of the screen display will change from GPS X to GPS . 5. When the KRUSEGO Receivers have been turned on, set to the required tour and languages, given to the passengers and the tour is ready to commence. (Instructions for setting up the KRUSEGO Receivers for a tour are on the following pages) If the selected tour commences with manually triggered “INTRODUCTION” commentary, the procedure to manually play the Introduction commentary is as follows:  Push the SAFETY button at the bottom right of the KRUSEGO Tour Master. If the display is flashing, the KRUSEGO Tour Master is in “power save mode”. To activate and play an Introduction commentary in “power save” mode, push the Safety button 2 X until the display shows “Select Safety Msg”. Use the ARROW UP and ARROW DOWN buttons to scroll through the list of manually triggered commentaries until the desired “INTRODUCTION” commentary is displayed.  Firmly push the BLUE Play/Pause button ONCE to play the “INTRO” commentary. “Triggered” appears in the display to confirm the instruction to play the “INTRO” commentary has been transmitted to the KRUSEGO Receivers. Once activated, the KRUSEGO Tour Master Screen will revert to blinking and display “ON TOUR” and the selected tour and the GPS status. GPS COMMENTARY TRIGGERING When GPS Lock is obtained (GPS ) the KRUSEGO Tour Master will automatically send the instruction to the KRUSEGO Receivers to play the commentary relating to the vehicle’s location as the vehicle passes through a GPS trigger point. MANUAL COMMENTARY TRIGGERING All manually triggered commentaries are stored under the SAFETY button. To activate ANY manually triggered commentary the procedure is basically the same as Step 6 above. i.e. Push the SAFETY button at the bottom right of the KRUSEGO Tour Master. If the display is flashing, the KRUSEGO Tour Master is in “power save mode”. To activate and play any manually triggered commentary when the KRUSEGO Tour Master is in “power save mode”, push the Safety button 2 X until the display shows “Select Safety Msg”. Use the ARROW UP and ARROW DOWN buttons to scroll through the list of manually triggered commentaries until the required commentary is displayed. Once the required commentary is displayed, firmly push the BLUE Play/Pause button ONCE to play the selected commentary (“triggered” appear in the display to confirm the instruction to play the selected commentary has been transmitted to the KRUSEGO Receivers). Once activated, the KRUSEGO Tour Master Screen will revert to blinking and display “ON TOUR”, the selected tour and the GPS status. THE KRUSEGO RECEIVERS SETTING THE LANGUAGE 1. Turn the KRUSEGO Receivers on by SIMULTANEOUSLY pushing the MENU and POWER buttons. The KRUSEGO Receivers screen will default to “Select Tour” and one of the tour names”. 2. Scroll through the tours using the volume up/volume down button until the desired tour is displayed. Then press the MENU Button to confirm the tour. 3. The screen will now display SELECT Language and the last language that the KRUSEGO Receiver was set too. 4. Use the “Volume Up” and “Volume Down” buttons to toggle though the languages until the desired language is displayed. Once the desired language is displayed, push the MENU button to confirm the language choice. The Kruse Receiver screen will display the word “READY” and is now set for the tour. Note: If the receivers are collected back partway through the tour and placed back in the recharger they will automatically turn off. When resuming the tour, STEPS 1 and 2 to set the language will need to be configured again. SETTING THE VOLUME 1. To adjust the volume, use the Volume up and Volume down buttons. The Kruse Guide screen will display the volume level as it is changed 2. At the end of each tour, the Kruse Master Controller and Kruse Receivers are shut down either by holding the POWER button (the display will show “SHUTDOWN” and then count down 3 seconds before finally powering off) or simply place the Kruse Master Controller and Kruse receivers into the recharger and they will shut down automatically. FCC Compliance This device complies with part 15 of the FCC rules and regu…

Text truncated - open the document above for the full version.

KRUSE MULTILINGUAL SYSTEMS LIMITED PO BOX 41169 ST LUKES AUCKLAND 1346 1st September 2015 EMC Technologies (NZ) Ltd PO Box 68-307, Newton Auckland 1145 New Zealand Re: Authorisation to Act for Kruse Multilingual Systems Limited for FCC Certification Dear Mr Cutler, Kruse Multilingual Systems Limited wishes to appoint Andrew Cutler, Managing Director of EMC Technologies (NZ) Ltd to act on its behalf to obtain formal IC and FCC certification of our KRUSEGO Receiver. Any correspondence or additional information can be requested from me c/o: [email protected] Kind regards Jonathan Kruse Managing Director

____________________________________________________________________________________________________________________________________________________________________________ Page 11 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. 9. PHOTOGRAPHS External views ____________________________________________________________________________________________________________________________________________________________________________ Page 12 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Power supply unit

1. 50 channel frequency hopping spread spectrum RF signal from Tour Master 2. RF receiver with main oscillator of 30Mhz 3. Microcontroller running at 16Mhz as master processor 4. Keypad to control operation of controller 5. 128x32 OLED graphical display 6. Digital audio decoder with 12.288Mhz oscillator 7. Micro SD memory card 8. Power supply with 3.7V lithium cell, charger IC and switching regulator running at 4MHz 9. Analog audio output to headphones 10. 5v External power source from USB or wall adaptor for charging. FCC Labeling Standard warning text will not be placed on label as small size of text would make it very difficult to read. Figure 7: Explorer Label Placement Figure 8: Label Placement

____________________________________________________________________________________________________________________________________________________________________________ Page 13 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Internal views ____________________________________________________________________________________________________________________________________________________________________________ Page 14 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full.

____________________________________________________________________________________________________________________________________________________________________________ Page 1 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. EMC Technologies (NZ) Ltd PO Box 68-307, Newton Auckland 1145 47 MacKelvie Street, Grey Lynn, Auckland 1021 New Zealand Phone 09 360 0862 Fax 09 360 0861 E-Mail Address: [email protected] Web Site: www.emctech.com.au TEST REPORT Kruse GO Explorer Receiver tested to 47 Code of Federal Regulations Part 15 - Radio Frequency Devices Subpart A + B for Kruse Multilingual Systems Ltd Testing carried out by : ________________________________________ Andrew Cutler- General Manager Test Report issued with the authority of: ________________________________________ Andrew Cutler- General Manager ____________________________________________________________________________________________________________________________________________________________________________ Page 2 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Table of Contents 1. STATEMENT OF COMPLIANCE 3 2. RESULTS SUMMARY 3 3. INTRODUCTION 3 4. CLIENT INFORMATION 4 5. DESCRIPTION OF TEST SAMPLE 4 6. SETUPS AND PROCEDURES 6 7. TEST EQUIPMENT USED 10 8. ACCREDITATIONS 10 9. PHOTOGRAPHS 11 ____________________________________________________________________________________________________________________________________________________________________________ Page 3 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. 1. STATEMENT OF COMPLIANCE The Kruse GO Explorer Receiver complies with FCC Part 15 Subpart A + B as a Receiver when the methods as described in ANSI C63.4 - 2003 are applied. 2. RESULTS SUMMARY The results from testing, carried out between September 12 th and September 17 th 2013 are summarised in the following table: Clause Parameter Result 15.101 Equipment authorisation requirement. Certification required as the device would be categorised as a “Receiver”. 15.103 Exempted devices. Device is not exempt as it contains a digital device. 15.107 Conducted Emissions 0.15 - 30 MHz Complies with a 7.7 dB margin at 432.0 kHz (Quasi Peak) 15.109 Radiated Emissions 30 - 5000 MHz Complies with a 2.9 dB margin at 99.220 MHz (Vertical) 15.111 Antenna Terminal Disturbance 30 – 950 MHz Not applicable. Receiver does not have an external antenna port. 3. INTRODUCTION This report describes the tests and measurements performed for the purpose of determining compliance with the specification. The client selected the test sample. This report relates only to the sample tested. This report contains no corrections or erasures. Measurement uncertainties with statistical confidence intervals of 95% are shown below test results. Both Class A and Class B uncertainties have been accounted for, as well as influence uncertainties where appropriate. ____________________________________________________________________________________________________________________________________________________________________________ Page 4 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. 4. CLIENT INFORMATION Company Name Kruse Multilingual Systems Ltd Address PO Box 41169 St Lukes City Auckland 1346 Country New Zealand Contact Mr Shaun O’Donnell 5. DESCRIPTION OF TEST SAMPLE Brand Name Kruse Model Number GO Product Explorer Receiver Manufacturer Kruse Multilingual Systems Ltd Country of Origin New Zealand Serial Number Sample not serialized FCC ID 2AE66-KGE33 Product Description The device tested is part of a system that consists of one master unit and one or many receiver units. The receiver is powered using a re-chargable lithium polymer battery pack at 3.7 Vdc. The receiver plays an audio commentaries that is held on the receiver which is triggered by a pulse from the master unit. This pulse can be generated automatically by the master unit assessing its location using a GPS receiver or manually by the operator using the keypad on the master unit. ____________________________________________________________________________________________________________________________________________________________________________ Page 5 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Band of Operation: 902 – 928 MHz Modulation: Frequency hopping spread spectrum Number of channels: 50 Operating frequencies: 922.0 – 926.9 MHz Channel spacing: 100 kHz Rated Conducted Power: +10 dBm (10 mW) Frequencies in use: Microcontroller 16.000 MHz, Audio Decoder 12.288 MHz RF Module 30.000 MHz LCD power supply 4.000 MHz Main power supply 850.0 kHz Antenna Type: Internal antenna Power Supply: 3.7 Vdc internal lithium polymer battery pack Ports: Battery charger port Audio output port RF Module Hope RF RFM22B Transceiver that operates in receive mode only ____________________________________________________________________________________________________________________________________________________________________________ Page 6 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. 6. SETUPS AND PROCEDURES Standard The sample was tested in accordance with 47 CFR Part 15 Subpart A and B. Methods and Procedures The following measurement methods and procedures have been applied: - ANSI C63.4 – 2003 Section 15.101: Equipment authorisation requirement Certification as detailed in Subpart J of Part 2 is required for this device as it would be classed as a Class B computer peripheral. Section 15.107: Conducted limits Conducted Emissions testing was carried out over the frequency range of 150 kHz to 30 MHz which was carried out at the laboratory’s MacKelvie Street premises in a 2.4 m x 2.4 m x 2.4 m screened room Testing was carried out using a representative AC power supply s…

Text truncated - open the document above for the full version.

____________________________________________________________________________________________________________________________________________________________________________ Page 15 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Conducted emissions test setup ____________________________________________________________________________________________________________________________________________________________________________ Page 16 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Radiated emissions setup – Standing up right ____________________________________________________________________________________________________________________________________________________________________________ Page 17 of 17 Test Report No 130901.3 26 th September 2013 This report may not be reproduced except in full. Laying flat Edge on ____________________________________________________________________________________________________________________________________________________________________________ Page 30 of 32 Test Report No 130901.1 26 h September 2013 This report may not be reproduced except in full. Radiated emissions test set up photos – Below 30 MHz Radiated emissions test set up photos – Above 30 MHz