2AEIM-WC1Wireless Phone Charger

Model S/X Wireless Charger The Model S/X wireless phone charger can charge your Qi-enabled smartphone at up to 7.5W of power for Model S/X. Once installed, simply push on the center console rear bin lid to open and place your smartphone in the phone charger, which is located on the back of the bin cover. The wireless phone charger uses one of the front USB ports to charge. Installing Wireless Phone Charger To install: 1. Open the rear bin storage area in the center console. This area is the storage portion closest to the cup holders, where the 12V power socket and USB ports are located. 2. Remove the rubber mat from the bottom of the console. 3. Lower the wireless phone charger onto the back of the console storage cover while open. You will hear a snap when it has secured tightly. 4. Locate the USB ports and insert the charger into either port. 5. Route the wire through the wiring indent and ensure the wire does not stick up. 6. Reinstall the plastic mat in the center console. 7. Place your smartphone into the wireless phone charger. It should fit snugly and will automatically start charging. Model S/X will charge your smartphone only when the vehicle is powered on (i.e., the touchscreen is on, and you are in your vehicle). You smartphone will not continue to charge if you leave it plugged in after exiting the vehicle. Model S/X will not charge your smartphone if the vehicle’s battery is discharged. NOTE: The wireless phone charger many not work if your phone case is too large or made of medal. Take the phone out of the case and place the phone on the charger. FCC and IC Certification Component Manufacturer Model Operating Frequency (KHz) FCC ID IC Wireless charger Tesla WC1 127.7 2AEIM-WC1 20098-WC1 The devices listed above comply with Part 15 of the FCC rules and Industry Canada's license- exempt RSS Standard(s) and EU Directive 2014/53/EU. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Changes or modifications not expressly approved by Tesla could void your authority to operate the equipment Note: Radiation Exposure Statement The product comply with the FCC/IC RF Exposure for Low Power Consumer Wireless Power Transfer. RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure that compliance was demonstrated at 20cm and greater separation from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme à l'exposition RF IC pour le transfert de puissance sans fil de consommateurs de faible puissance. La limite d'exposition RF fixée pour un environnement non contrôlé est sans danger pour le fonctionnement prévu tel que décrit dans ce manuel. L'exposition RF supplémentaire que la conformité a été démontrée à 20cm et plus de séparation du corps de l'utilisateur ou de mettre l'appareil à la puissance de sortie inférieure si une telle fonction est disponible. Canada CAN ICES-3 (B)/NMB-3(B) Caution: This equipment and its antennas must not be co-located or operated with another antenna or transmitter. Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. EU Declaration of Conformity Hereby, Tesla Motors, Inc. , declares that the radio equipment Wireless Charging, WC1, is in compliance with Directive 2014/53/EU. The full test of the EUT declaration of conformity is available at the following. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radiation Exposure Statement: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Frequency band in which the radio equipment operates: 127.7 kHz Maximum power transmitted: < 0.01mW Mexico La Operación de Este Equipo no está Sujeta a las dos condiciones siguientes: Es Posible Que Este Equipo o Dispositivo no causar interferenciaperjudicial. Este Equipo o Dispositivo debe Aceptar Cualquier interferencia. Incluyendo La Que Pueda causar do Operación no Deseada. Model name: Wireless Phone Charger Manufacturer: Tesla, Inc. Model Number: WC1 Max. output: 7.5W Input:5V 3.5A

Date: 2019-11-28 FCC ID:2AEIM-WC1 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Peng Zhang, Sr Certification Engineer Tesla Motors, Inc Tel: 650-681-5000 Fax: 650-681-5000 E-mail: [email protected]

Date: 2019-11-28 FCC ID:2AEIM-WC1 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Peng Zhang, Sr Certification Engineer Te s l a M o t o r s , I n c Tel: 650-681-5000 Fax: 650-681-5000 E-mail: [email protected]

Date: 2019-11-28 FCC ID:2AEIM-WC1 AUTHORIZATION LETTER To Whom It May Concern: Tesla Motors, Inc hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on Tesla Motors, Inc‘s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Peng Zhang, Sr Certification Engineer Tesla Motors, Inc Tel: 650-681-5000 E-mail: [email protected]

Tesla, Inc. 3500 Deer Creek Road, Palo Alto, CA 94304 p +650 681 5100 f +650 681 5101 Federal Communications Commission Office of Engineering & Technology Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Via Electronic Filing Date: Oct 3, 2019 Re: Authorized Personnel for Grantee Code 2AEIM To Whom It May Concern: I currently serve as Tesla, Inc’s (Tesla) grantee contact (Grantee Code 2AEIM) for Federal Communications Commission (FCC) equipment authorizations. As prescribed in KDB 852134 Authorized Policy Form 731, I authorize the following personnel to act on Tesla’s behalf with regard to all matters that relate to FCC equipment authorization (i.e., signing Form 731, attestation letters, and confidentiality request letters). This (these) individual(s) also is (are) authorized to assign additional persons to act on Tesla’s behalf as authorized agents. Authorized Personnel:  Peng Zhang This authorization is valid until further written notice from any of Tesla’s authorized grantee contact(s). Sincerely Yours, Sean Lui Sr. Staff Charging Compliance Engineer 3500 Deer Creek Road, Palo Alto, California US 94304 Phone: (650)681-5109 [email protected]

Reference No.: 191111D05-ExtPho Page 1 / 3 CONSTRUCTION PHOTOS OF EUT Reference No.: 191111D05-ExtPho Page 2 / 3 Reference No.: 191111D05-ExtPho Page 3 / 3

REV. DESCRIPTION 更改說明 PRODUCT LABEL 6.TO BE PRINTED IN PRODUCTION USING DMX300 RIBBON ; 7.THE DIMENSIONS (2) ARE INCOMING INSPECTION AND CRITICAL. 8. ALL TOLERANCE ARE +/-0.01MM . 9.Requirement of PRIMAX Part: 1).Comply with PRIMAX QW-5Q002 Green Product Chemical Substances Specification . 2).Follow customer's specification as required. Follow Halogen- Free requirement : Br<900 ppm, Cl<900 ppm, Br+Cl< 1500 ppm if required. "Product must be halogen free" ENG.APPROVAL 修改人 審核 3). 3 WCI_T75 Zhibing.Wu Becky.Liu 2019/12/2 致伸科技股份有限公司 PRIMAX ELECTRONICS LTD. NOTE : 2.MATERIAL : White PET 50g 3.PRINT COLOR: BLACK CODE QR CODE 4.THE BARCODE ARRANGEMENT IS FOLLOWING THE STANDARD ASII CODES. 5.BARCODE ARRANGEMENT : 1546873-00-A: S AOV 19295 000001 19295==>Build DateYYJJJ YY=(18=2018,19=2019...) 000001== >Unique ID CCCCCC (DIGITS 0~9 AND CAPITAL LETTERS A~Z) Unique ID Part Number Build Date * JJJ=Refer to TABLE A1&TABLE A2 Build Site Code AOV= :Build Site CodeSSS P Fixed code Fixed code 二維碼掃出來的信息是:P:SAOV192950000011546873-00-A 2019/12/2 1 產品後蓋上2pcs label(1:1) 1.All fonts is 4pt 1 Model Name: Wireless Phone Charger Manufacturer: Tesla, Inc. 76mm 12mm XXXXXXXXXX R-C-Tsa-WC1 FCC ID: 2AEIM-WC1 IC: 20098-WC1 Input:5V 3.5A Model Number: WC1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device mu st accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B) TRC/XX/XXXX/XXX Made in China (P)1546873-00-A (S)AOV19295000001 2 A910000000920V7.PDF A910000000920 R3D160 RoHS TRC/XX/XXXX/XXX CAN ICES-3 (B)/NMB-3(B) Made in China (P)1546873-00-A (S)AOV19295000001 R3D160 RoHS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3 2 1 致伸科技股份有限公司 PRIMAX ELECTRONICS LTD. REV. DESCRIPTION 更改說明 ENG.APPROVAL 修改人審核 RequirementofPRIMAXPart: 1).ComplywithPRIMAXQW-5Q002GreenProduct ChemicalSubstancesSpecification. 2).Followcustomer'sspecificationasrequired. FollowHalogen-Freerequirement:Br<900ppm,Cl<900ppm, Br+Cl<1500ppmifrequired. ? "Product must be halogen free" 3). bÄòJanFebMarAprMayJunJulAugSepOctNovDec 11326091121152182213244274305335 22336192122153183214245275306336 33346293123154184215246276307337 44356394124155185216247277308338 55366495125156186217248278309339 66376596126157187218249279310340 77386697127158188219250280311341 88396798128159189220251281312342 99406899129160190221252282313343 10104169100130161191222253283314344 11114270101131162192223254284315345 12124371102132163193224255285316346 13134472103133164194225256286317347 14144573104134165195226257287318348 15154674105135166196227258288319349 16164775106136167197228259289320350 17174876107137168198229260290321351 18184977108138169199230261291322352 19195078109139170200231262292323353 20205179110140171201232263293324354 21215280111141172202233264294325355 22225381112142173203234265295326356 23235482113143174204235266296327357 24245583114144175205236267297328358 25255684115145176206237268298329359 26265785116146177207238269299330360 27275886117147178208239270300331361 28285987118148179209240271301332362 292988119149180210241272302333363 303089120150181211242273303334364 313190151212243304365 TABLE A1: Julian Date Calendar WCI_T75 Zhibing.Wu Becky.Liu PRODUCT LABEL A910000000920 A910000000920V7.PDF 2019/12/2 2019/12/2 3 3 1 致伸科技股份有限公司 PRIMAX ELECTRONICS LTD. REV. DESCRIPTION 更改說明 ENG.APPROVAL 修改人審核 RequirementofPRIMAXPart: 1).ComplywithPRIMAXQW-5Q002GreenProduct ChemicalSubstancesSpecification. 2).Followcustomer'sspecificationasrequired. FollowHalogen-Freerequirement:Br<900ppm,Cl<900ppm, Br+Cl<1500ppmifrequired. ? "Product must be halogen free" 3). bÄòJanFebMarAprMayJunJulAugSepOctNovDec 11326192122153183214245275306336 22336293123154184215246276307337 33346394124155185216247277308338 44356495125156186217248278309339 55366596126157187218249279310340 66376697127158188219250280311341 77386798128159189220251281312342 88396899129160190221252282313343 994069100130161191222253283314344 10104170101131162192223254284315345 11114271102132163193224255285316346 12124372103133164194225256286317347 13134473104134165195226257287318348 14144574105135166196227258288319349 15154675106136167197228259289320350 16164776107137168198229260290321351 17174877108138169199230261291322352 18184978109139170200231262292323353 19195079110140171201232263293324354 20205180111141172202233264294325355 21215281112142173203234265295326356 22225382113143174204235266296327357 23235483114144175205236267297328358 24245584115145176206237268298329359 25255685116146177207238269299330360 26265786117147178208239270300331361 27275887118148179209240271301332362 28285988119149180210241272302333363 29296089120150181211242273303334364 303090121151182212243274304335365 313191152213244305366 TABLE A2: Julian Date Calendar Leap Year WCI_T75 Zhibing.Wu Becky.Liu PRODUCT LABEL A910000000920 A910000000920V7.PDF 2019/12/2 2019/12/2

Reference No.: 191111D05-IntPho Page 1 / 3 CONSTRUCTION PHOTOS OF EUT Reference No.: 191111D05-IntPho Page 2 / 3 Reference No.: 191111D05-IntPho Page 3 / 3

Report No.: SA191111D05 Page No. 1 / 16 Report Format Version: 6.1.1 RF Exposure Test Report Report No.: SA191111D05 FCC ID: 2AEIM-WC1 Test Model: WC1 Received Date: Nov. 11, 2019 Test Date: Dec. 26, 2019 Issued Date: Dec. 27, 2019 Applicant: Tesla Motors, Inc Address: 3500 Deer Creek Road Palo Alto California United States 94304 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan FCC Registration / Designation Number: 198487 / TW2021 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA191111D05 Page No. 2 / 16 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 General Information .............................................................................................................................. 5 2.1 General Description of EUT ................................................................................................................ 5 3 RF Exposure .......................................................................................................................................... 6 3.1 Description of Support Units ............................................................................................................... 6 3.1.1 Configuration of System under Test .................................................................................................... 6 3.2 Test Setup ........................................................................................................................................... 7 3.3 Test Instruments .................................................................................................................................. 7 3.4 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 8 3.5 EUT Configuration and Test Point Description .................................................................................... 9 4 Calculation Result of Maximum Conducted Power .......................................................................... 11 5 Photographs of the Test Configuration ............................................................................................ 16 Report No.: SA191111D05 Page No. 3 / 16 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA191111D05 Original release. Dec. 27, 2019 Report No.: SA191111D05 Page No. 4 / 16 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Wireless Phone Charger Brand: Tesla Test Model: WC1 Sample Status: Engineering sample Applicant: Tesla Motors, Inc Test Date: Dec. 26, 2019 Standards: FCC Part 2 (Section 2.1091) FCC Part 1 (Section 1.1307(c) and (d), Section 1.1310) KDB 680106 D01 RF Exposure Wireless Charging v03 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Dec. 27, 2019 Annie Chang / Senior Specialist Approved by : , Date: Dec. 27, 2019 Rex Lai / Associate Technical Manager Report No.: SA191111D05 Page No. 5 / 16 Report Format Version: 6.1.1 2 General Information 2.1 General Description of EUT Product Wireless Phone Charger Brand Tesla Test Model WC1 Sample Status Engineering sample Power Supply Rating I/P rating: 5Vdc O/P rating: 7.5W Modulation Type FSK Operating Frequency 127.7 kHz Antenna Type Coil antenna Field Strength 91.53dBuV/m Dimensions 43.45cm 2 (diameter = 47mm) Accessory Device N/A Data Cable Supplied Shielded USB cable (0.3m) attached on EUT Maximum Power Output from the Charging Coil 7.5W Note: The EUT is a Wireless Phone Charger with Qi function. Report No.: SA191111D05 Page No. 6 / 16 Report Format Version: 6.1.1 3 RF Exposure 3.1 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID…

Text truncated - open the document above for the full version.

Report No.: RF191111D05 Page No. 1 / 30 Report Format Version: 6.1.1 FCC Test Report Report No.: RF191111D05 FCC ID: 2AEIM-WC1 Test Model: WC1 Received Date: Nov. 11, 2019 Test Date: Nov. 28, 2019 Issued Date: Nov. 29, 2019 Applicant: Tesla Motors, Inc Address: 3500 Deer Creek Road Palo Alto California United States 94304 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan FCC Registration / Designation Number: 198487 / TW2021 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF191111D05 Page No. 2 / 30 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 6 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 7 3.3 Description of Support Units ............................................................................................................... 8 3.3.1 Configuration of System under Test .................................................................................................... 8 3.4 General Description of Applied Standards .......................................................................................... 9 4 Test Types and Results ...................................................................................................................... 10 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 10 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 10 4.1.2 Test Instruments ................................................................................................................................. 11 4.1.3 Test Procedures ................................................................................................................................. 12 4.1.4 Deviation from Test Standard ............................................................................................................ 12 4.1.5 Test Set Up ........................................................................................................................................ 13 4.1.6 EUT Operating Conditions ................................................................................................................. 13 4.1.7 Test Results ....................................................................................................................................... 14 5 Pictures of Test Arrangements .......................................................................................................... 29 Appendix – Information of the Testing Laboratories ................................................................................. 30 Report No.: RF191111D05 Page No. 3 / 30 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued RF191111D05 Original release. Nov. 29, 2019 Report No.: RF191111D05 Page No. 4 / 30 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Wireless Phone Charger Brand: Tesla Test Model: WC1 Sample Status: Engineering sample Applicant: Tesla Motors, Inc Test Date: Nov. 28, 2019 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.209) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., …

Text truncated - open the document above for the full version.

Reference No.: SA191111D05 Page No. 1 / 7 PHOTOGRAPHS OF THE TEST CONFIGURATION Charging Mode EUT Side Left Right Top Bottom Z-axis Actual Distance install in the Vehicular (cm) 8 8 0 2.77 1.044 Measurement Distance (cm) 8 8 7 2 1 Test result defined it as 0 cm, please see report page 11. Test result defined it as 0 cm, please see report page 11. When cell phone plug in to the EUT, that have 7 cm gap between transmitter and human body. Te s t result defined it as 0 cm, please see report page 11. Test result defined it as 0 cm, please see report page 11. Test result defined it as 0 cm, please see report page 11. Reference No.: SA191111D05 Page No. 2 / 7 Standby Mode EUT Side Left Right Top Bottom Z-axis Actual Distance install in the Vehicular (cm) 8 8 Not perform. Since the EUT will not open the case during the standby mode. 2.77 1.044 Measurement Distance (cm) 8 8 2 1 Test result defined it as 0 cm, please see report page 13. Test result defined it as 0 cm, please see report page 13. Test result defined it as 0 cm, please see report page 13. Test result defined it as 0 cm, please see report page 13. Reference No.: SA191111D05 Page No. 3 / 7 H-Field (Charging Mode - Left) H-Field (Charging Mode - Right) Reference No.: SA191111D05 Page No. 4 / 7 H-Field (Charging Mode - Bottom) H-Field (Charging Mode - Z- axis) Reference No.: SA191111D05 Page No. 5 / 7 H-Field (Charging Mode - Top) Reference No.: SA191111D05 Page No. 6 / 7 H-Field (Standby Mode - Left) H-Field (Standby Mode - Right) Reference No.: SA191111D05 Page No. 7 / 7 H-Field (Standby Mode - Bottom) H-Field (Standby Mode - Z-axis) --- END ---

Reference No.: RF191111D05 Page No. 1 / 6 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST (Mode A) <Frequency Range below 30MHz> Reference No.: RF191111D05 Page No. 2 / 6 RADIATED EMISSION TEST (Mode B) <Frequency Range below 30MHz> Reference No.: RF191111D05 Page No. 3 / 6 RADIATED EMISSION TEST (Mode C) <Frequency Range below 30MHz> Reference No.: RF191111D05 Page No. 4 / 6 RADIATED EMISSION TEST (Mode A) <Frequency Range above 30MHz> Reference No.: RF191111D05 Page No. 5 / 6 RADIATED EMISSION TEST (Mode B) <Frequency Range above 30MHz> Reference No.: RF191111D05 Page No. 6 / 6 RADIATED EMISSION TEST (Mode C) <Frequency Range above 30MHz>