2AEKR-TF10EA2Tablet PC

Quick Start Guide For TF10EA2 1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation 2 RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The highest SAR value for the device as reported to the FCC is 1.22 W/kg when placed next to the body. CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. ATTENTION RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉ E PAR UN TYPE INCORRECT. RECYCLEZ LES BATTERIES USAGÉ ES SELON LES INSTRUCTIONS. To prevent possible hearing damage, do not listen at high volume levels for long periods. Attention: Teachers, Parents and Adult Supervisors This product is an educational tool designed for school children, ages 6 and up. There must be supervision by an adult on school children under 10 when using this tablet. It is a must to have a thorough explanation to students on safe and proper handling of the tablet, power supply, battery pack, and power cord. 3 Be sure to keep the power cord away from younger children Please ensure that students understand the following:  As with all electrical products, precautions should be observed during handling and use to prevent electric shock. The power supply (adapter) should not be handled by the children.”  Emphasize to students that this device is an educational tool and not a toy. The computer, power supply, battery pack or power cord should not be dropped, crushed, stepped on or otherwise abused.  Ensure students understand the safe and proper handling of power cord and power supply. Misuse could result in serious injury.  The teacher, parent or adult supervisor should periodically inspect the computer; power supply and power cord for damage and replace it, if necessary.  Students should report any damage or loose parts to their teacher, parents or adult supervisor, immediately.  Do not leave the tablet plugged in or “on” when enclosed in a non-vented container, such as a school backpack, as overheating may occur.  It is recommended that students should take a 5 minute break every 30 minutes of use. Safety Precautions The following are lists of precautionary measure the students must understand before using this computer inside the classroom or home environment: 4 1. Do not place near the fire or other sources of heat. 2. Do not expose to magnetic fields. 3. Do not expose to direct sunlight. 4. Do not expose to rain or moisture. 5. Do not place heavy objects to add heavy pressure on the computer. 6. Do not drop the computer. Package contents Carefully unpack your box and take out the items listed below. If any of the items are missing or damaged, please contact your dealer immediately: • One tablet • One keyboard docking • One USB cable • One AC adapter • One stylus •This guide 5 Tablet layout No. Name No. Name 1 Front facing camera 5 Input/output cabinet (See page 7) 2 Power lock 6 Touchscreen 3 Microphone 7 Stylus holder 4 Volume up/down 8 Stylus 6 No. Name No. Name 1 Power lock 3 Docking connector 2 Rear facing camera 4 Stylus holder 7 No. Name No. Name 1 Rubber cover 4 Micro SIM card slot 2 Micro USB DC IN / Micro USB port 5 Micro HDMI port 3 Micro SD card slot 6 Headphone jack 8 No. Name No. Name 1 Docking connector 3 Touchpad 2 Windows Key button 9 Charging your tablet If your tablet is just being unpacked from the box, you need to charge the tablet first. It will take around 4 to 5 hours to be fully charged. 1. Plug the USB head of the cable into the adapter. 2. Plug the micro-USB head of the cable - with the side marked with “B” or an icon facing down - into the micro-USB port on your tablet. 3. Plug the adapter into a wall-socket. Note: If the remaining power in your battery capacity is 90% or above, plugging the adapter will not fully charge your battery. 10 Powering ON/OFF your tablet To power on your tablet Press down the power button (normally 1 to 2 seconds) until you see the screen turn on. To power off your tablet For And…

Text truncated - open the document above for the full version.

RF_160, Issue 03 Declaration of Authorization We Name: ELITEGROUP COMPUTER SYSTEMS CO., LTD Address: No.239, Sec. 2, Tiding Blvd., Neihu Dist, Taipei City 14, Taiwan City: Taipei ........................................... Country: Taiwan ....................................................... Declare that: Name Representative of agent: Miro Chueh. (1) Agent Company name: Cerpass Technology (Suzhou) Co.,Ltd Address: No.66,Tangzhuang Road, Suzhou Industrial Park, Jiangsu 215006, China City: Suzhou........ Country: China is authorized to apply for Certification of the following product(s): Product description: ......... Tablet PC ............................... Type designation: ...... TF10EA2 .............................................. Trademark: ...... .............................................. on our behalf. Date: 2015-8-6....................... City: Taipei .................... Name: Patrick Yen .................... (2) Function: Senior Manager................ Signature: ...............................

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) Equipment: Tablet PC Trademark(s) and Model(s): TF10EA2 Manufacturer: ELITEGROUP COMPUTER SYSTEMS CO., LTD. FCC ID in case other parts of this equipment are subject to certification: 2AEKR-TF10EA2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration: Test report number: Issue date: SEFD1507008 2015-9-8 The following manufacturer/importer/entity (located in the USA) is responsible for this declaration: Company name: ELITEGROUP COMPUTER SYSTEMS CO., LTD Name/Title (legal representative): Patrick Yen / Senior Manager Address: No.239, Sec. 2, Tiding Blvd., Neihu Dist, Taipei City 14, Taiwan Phone: 02-21621177 ext 85400 Fax: E-mail: [email protected] Date: 2015-8-6 Signature: FCC

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: ELITEGROUP COMPUTER SYSTEMS CO., LTD Address: No.239, Sec.2, Ti Ding Blvd., Neihu Dist City: Taipei Country: Taiwan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2AEKR-TF10EA2 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: 180 days (notes 2, 3, 4, 5) Date: 2015-08-6 Name and signature of applicant: Patrick Yen Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

PN:41H105-XXXXXX (1) Material#25 Polyester film transparent+screen print(25#) (2) Finish#25 Plain film() (3) Adhesiveacrylic adhesive (4) Dimension35X8mm (5) Printing colorPanton cool gray 7C (6) Tolerance:+0.5,-0.5 (7) Unitmm RoHS compliance: YES This part should pass Elite's environment test The printing factory should acquire the UL certificate for the material of label for this part. The printing drawings, characters and lines should be clear. The ink should be saturated, even and opaque. No dotted line will be allowed. TF10EA2_Rating label_STD_FCC/CE/UL_V1 20150610 Safety/EMC/RF V1 R1*4 35mm 8 mm Safety Made in China Rating:5V 2A Tablet PC Model:TF10EA2 41H105-XXXXXX FCC ID: 2AEKR-TF10EA2 Made in China Rating:5V 2A Tablet PC Model:TF10EA2 41H105-XXXXXX FCC ID: 2AEKR-TF10EA2 A3 1/1 ELITEGROUP COMPUTER CROP. Aaron 4/7 TF10EA2 Intel insde &label Location Intel 19.0 Laser Engraving 只出平板 Rating Label 35*8mm S/N Label 40*8mm 7 . 7 2 3 . 0 28.6 A3 1/1 ELITEGROUP COMPUTER CROP. Aaron 4/7 TF10EA2 Intel insde &label Location Intel 整機賣 19.0 Laser Engraving S/N Label 40*8mm 7 . 7 2 3 . 0 A3 1/1 ELITEGROUP COMPUTER CROP. 整機賣 Aaron 12/1 TF10EA2 Intel insde &label Location Intel Rating Label 35*8mm S/N Label 40*8mm 3 . 8 41.5 Only Docking

CERPASS TECHNOLOGY CORP. Cerpass Technology (Suzhou) Co., Ltd Tel: 86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 1 EXTERNAL PHOTOGRAPHS OF EUT 1) EUT Photo 2) EUT Photo

CERPASS TECHNOLOGY CORP. Report No.: DEFQ1507117 Cerpass Technology Corp. Issued Date : Aug. 04, 2015 Page No. : 1 of 34 FCC RADIO TEST REPORT Applicant : ELITEGROUP COMPUTER SYSTEMS CO., LTD. Address : No.239, Sec. 2, Tiding Blvd., Neihu Dist, Taipei City 14, Taiwan (R.O.C) Manufacturer : ELITEGROUP COMPUTER SYSTEMS CO., LTD. Address : No.239, Sec. 2, Tiding Blvd., Neihu Dist, Taipei City 14, Taiwan (R.O.C) Equipment : Tablet PC Model No. : TF10EA2 I HEREBY CERTIFY THAT : The sample was received on Jul 27, 2015 and the testing was carried out on Aug. 02, 2015 at Cerpass Technology Corp. The test result refers exclusively to the test presented test model / sample. Without written approval of Cerpass Technology Corp., the test report shall not be reproduced except in full. Approved by: Miro Chueh EMC/RF B.U. Manager Laboratory Accreditation: Cerpass Technology Corporation Test Laboratory NVLAP LAB Code: 200954-0 TAF LAB Code: 1439 Cerpass Technology(SuZhou) Co., Ltd. NVLAP LAB Code: 200814-0 CNAS LAB Code: L5515 CERPASS TECHNOLOGY CORP. Report No.: DEFQ1507117 Cerpass Technology Corp. Issued Date : Aug. 04, 2015 Page No. : 2 of 34 Contents 1. Summary of Test Procedure and Test Results ......................................................................................... 5 1.1 Applicable Standards ........................................................................................................................5 2. Test Configuration of Equipment under Test ........................................................................................... 6 2.2 Feature of Equipment under Test .....................................................................................................6 2.3 Test Mode & Test Software ...............................................................................................................6 2.4 Test Manner ......................................................................................................................................7 2.5 Description of Test System ...............................................................................................................7 2.6 General Information of Test ..............................................................................................................8 3. Test Equipment and Ancillaries Used for Tests ....................................................................................... 9 4. Antenna Requirements ............................................................................................................................. 10 4.7 Standard Applicable ....................................................................................................................... 10 4.8 Antenna Construction and Directional Gain .................................................................................. 10 5. Test of Conducted Emission .................................................................................................................... 11 5.9 Test Limit ......................................................................................................................................... 11 5.10 Test Procedures .............................................................................................................................. 11 5.11 Typical Test Setup.......................................................................................................................... 12 5.12 Test Result and Data ..................................................................................................................... 13 6. Test of Radiated Emission ....................................................................................................................... 15 6.1 Test Limit ........................................................................................................................................ 15 6.2 Test Procedures ............................................................................................................................. 15 6.3 Typical Test Setup.......................................................................................................................... 16 6.4 Test Result and Data ..................................................................................................................... 17 6.5 Test Result and Data (30MHz ~ 1GHz) ......................................................................................... 17 6.6 Test Result and Data (1GHz ~ 25GHz) ......................................................................................... 18 6.7 Restricted Bands of Operation ...................................................................................................... 21 6.8 Restrict Band Emission Measurement Data .................................................................................. 22 7. Test of Spurious Emission (Conducted) ................................................................................................. 23 7.1 Test Limit ........................................................................................................................................ 23 7.2 Test Procedure .............................................................................................................................. 23 7.3 Test Setup Layout .......................................................................................................................... 23 7.4 Test Result and Data ..................................................................................................................... 23 8. 6dB Bandwidth Measurement Data ......................................................................................................... 27 8.1 Test Limit ........................................................................................................................................ 27 8.2 Test Procedures ............................…

Text truncated - open the document above for the full version.

CERPASS TECHNOLOGY (SUZHOU)CO., LTD Report No.: SECR1507008 Cerpass Technology Corp. Issued Date : Jul 25, 2015 Tel:86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 1 of 82 FCC TEST REPORT According to CFR47 §15.247 Applicant : EGROUP COMPUTER SYSTEMS CO., LTD. Address : No.239, Sec. 2, Tiding Blvd., Neihu Dist, Taipei City 14, Taiwan (R.O.C) Equipment : Tablet PC Model No. : TF10EA2  The test result refers exclusively to the test presented test model / sample.  Without written approval of Cerpass Technology Corp. the test report shall not be reproduced exc- ept in full.  The test report must not be used by the clients to claim product certification approval by NVLAP or any agency of the Government. I HEREBY CERTIFY THAT : The measurements shown in this test report were made in accordance with the procedures given in ANSI C63.10– 2013 and the energy emitted by this equipment was passed. CISPR PUB. 22 and FCC Part 15 in both radiated and conducted emission class B limits. Testing was carried out on Jul 25, 2015 at Cerpass Technology Corp. Prepared By: ___________________ Laboratory accreditation Leo Chen Approved By: ___________________ Miro Chueh CERPASS TECHNOLOGY (SUZHOU)CO., LTD Report No.: SECR1507008 Cerpass Technology Corp. Issued Date : Jul 25, 2015 Tel:86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 2 of 82 Release History Attachment No. Date Description SECR1507008 2015-07-25 Initial release CERPASS TECHNOLOGY (SUZHOU)CO., LTD Report No.: SECR1507008 Cerpass Technology Corp. Issued Date : Jul 25, 2015 Tel:86-512-6917-5888 Fax: 86-512-6917-5666 Page No. : 3 of 82 Table of Contents 1. Report of Measurements and Examinations .............................................................................................. 5 1.1 List of Measurements and Examinations .....................................................................................................5 2. Test Configuration of Equipment under Test ............................................................................................. 6 2.1 Feature of Equipment under Test .................................................................................................................6 2.2 Carrier Frequency of Channels ....................................................................................................................7 2.3 Power Setting Levels ....................................................................................................................................7 2.4 Duty cycle .....................................................................................................................................................8 2.5 Test Manner ..................................................................................................................................................9 2.6 Description of Test System ...........................................................................................................................9 2.7 General Information of Test ..........................................................................................................................9 2.8 Measurement Uncertainty ......................................................................................................................... 10 3. Antenna Requirements ................................................................................................................................ 11 3.1 Standard Applicable .................................................................................................................................... 11 3.2 Antenna Construction and Directional Gain ............................................................................................... 11 4. Test of Conducted Emission ...................................................................................................................... 12 4.1 Test Limit ................................................................................................................................................... 12 4.2 Test Procedures......................................................................................................................................... 12 4.3 Typical Test Setup ..................................................................................................................................... 13 4.4 Measurement Equipment .......................................................................................................................... 13 4.5 Test Result and Data ................................................................................................................................. 14 5. Test of Radiated Emission ......................................................................................................................... 16 5.1 Test Limit ................................................................................................................................................... 16 5.2 Test Procedures......................................................................................................................................... 16 5.3 Typical Test Setup ..................................................................................................................................... 17 5.4 Measurement Equipment .......................................................................................................................... 19 5.5 Test Result and Data ................................................................................................................................. 20 6. Occupied Bandwidth ................................................................................................................................... 26 6.1 Test Limit ................................................................................................................................................... 26 6.2 Test Pro…

Text truncated - open the document above for the full version.

APPENDIX D. Photographs of Test Setup Tablet Back with gap 0mm Tablet Front with gap 0mm Tablet Edge1 with gap 0mm Tablet Edge2 with gap 0mm

TEST SETUP PHOTOGRAPHS OF EUT RADEATED EMISSION TEST 30MHz~1000MHz 1GHz~18GMHz