2AET4TAP100Wi-Fi ACCESS POINT

T ECHNICAL INFORMATION R adio specifications RF technologies IWiFi Max RF Power I20 dBm@WiFi Integrated antennas specifications WiFi antenna I2x 2400~2500 MHz, peak gain< 4.9 dBi, omnidirectional Powering PoE Iinput: 44-57 VDC, 802.3af COMPLIANCE INFO RMATION TAP100 access poi nt must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments. Simplified EU and UK Declaration of Conformity H ereby, TEL TON I KA NETWORKS declares that this TAP100 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and with Radio Equipment Regulations 2017. T he full text of the EU and UK Declaration of Conformity is available at the following internet address: wiki.teltonika-networks.com/view/Certificates D etailed compliance information is available at the following internet address: wiki.teltonika-networks.com/view/Certificates FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this d evice must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the sep aration between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. I SED : This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subje ct to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables a ux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doi t accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF Exposure Compliance: This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé. Cet ém etteur ne doit pas être colocalisé ou f onctionner en conjonction avec une autre antenne ou un autre émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le r adiateur et votre corps. 4!:.TELTONIKA I Networks I■ ■

Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name UAB Teltonika Networks Address K. Barsausko st. 66 LT-51436 Kaunas Lithuania Grantee Code 2AET4 FCC ID 2AET4TAP100 Authorized Contact Name Mantas Cizauskas Contact Email [email protected] Contact Phone (+370)65546942 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List [UAB Teltonika Networks] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [UAB Teltonika Networks] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date: 2023/06/15 Print Name: Mantas Cizauskas Title: Head of R&D Department

Swedbank AB LT78 7300 0101 6274 0111 S.W.I.F.T. HABALT22 Registration code 305579419 VAT number LT100013223510 1 www.teltonika-networks.com [email protected] Теl. +370 3 721 6110 TELTONIKA NETWORKS UAB K. Barsausko st. 66, LT-51436 Kaunas, Lithuania Data on the company is collected and stored in the Register of Legal Entities of the Republic of Lithuania. UNITED STATES DESIGNATED AGENT LETTER Date: 2023/07/12 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant U.S. designated agent Company Name: UAB Teltonika Networks Company Name: United Consulting Technology Services Co., Ltd. Grantee Code: 2AET4 FRN: Contact Name: 0033495714 David Wu Contact Name: Mantas Cizauskas Address: 17800 CASTLETON ST STE 665 CITY OF INDUSTRY CA 91748 United States Address: K. Barsausko st. 66 LT-51436 Kaunas Lithuania Telephone: (626) 217-4022 Telephone: (+370)65546942 Email: [email protected] Email: [email protected] Applicable Equipment: FCC ID: 2AET4TAP100 ATTN: Director of Certification: We, < UAB Teltonika Networks > and < United Consulting Technology Services Co., Ltd.> understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e- mail of the designated agent listed above. We, < UAB Teltonika Networks > and < United Consulting Technology Services Co., Ltd.> acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Mantas Cizauskas Name (Printed): David Wu Title: Head of R&D Department Title: CEO Swedbank AB LT78 7300 0101 6274 0111 S.W.I.F.T. HABALT22 Registration code 305579419 VAT number LT100013223510 2 www.teltonika-networks.com [email protected] Теl. +370 3 721 6110 TELTONIKA NETWORKS UAB K. Barsausko st. 66, LT-51436 Kaunas, Lithuania Data on the company is collected and stored in the Register of Legal Entities of the Republic of Lithuania. Signature: Signature:

Swedbank AB LT78 7300 0101 6274 0111 S.W.I.F.T. HABALT22 Registration code 305579419 VAT number LT100013223510 1 www.teltonika-networks.com [email protected] Теl. +370 3 721 6110 TELTONIKA NETWORKS UAB K. Barsausko st. 66, LT-51436 Kaunas, Lithuania Data on the company is collected and stored in the Register of Legal Entities of the Republic of Lithuania. Date: 2023/06/15 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2AET4TAP100 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with UAB Teltonika Networks. This authorization is valid until further written notice from the applicant. Sincerely, Print Name: Mantas Cizauskas Title: Head of R&D Department Signature: On behalf of Company: UAB Teltonika Networks Telephone: (+370)65546942 E-mail: [email protected]

Swedbank AB LT78 7300 0101 6274 0111 S.W.I.F.T. HABALT22 Registration code 305579419 VAT number LT100013223510 1 www.teltonika-networks.com [email protected] Теl. +370 3 721 6110 TELTONIKA NETWORKS UAB K. Barsausko st. 66, LT-51436 Kaunas, Lithuania Data on the company is collected and stored in the Register of Legal Entities of the Republic of Lithuania. Date: 2023/06/15 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: 2AET4TAP100 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. • Schematic(s) • Block Diagrams • Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within the aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. • External Photos • Internal Photos • Test Setup Photos • User manual(s) Sincerely, Print Name: Mantas Cizauskas Title: Head of R&D Department Signature: On behalf of Company: UAB Teltonika Networks Telephone: (+370)65546942 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 1 of 6 Appendix External Photos for SZCR2306001795AT FCC ID:2AET4TAP100 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 2 of 6 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 3 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 4 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 5 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 6 of 6 - End of the Appendix -

1/:.TELTON/KA I Networks 7 I Reset ! I FCC ID: 2AET4TAP100 IC: 26511-TAP100 802.3af PoE Class 1

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 1 of 3 Appendix Internal Photos for SZCR2306001795AT FCC ID:2AET4TAP100 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 2 of 3 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 3 of 3 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179503 Page: 1 of 11 Keny Xu EMC Laboratory Manager RF EXPOSURE EVALUATION REPORT Application No.: SZCR2306001795AT Applicant: UAB Teltonika Networks Address of Applicant: K. Barsausko st. 66, Kaunas, LT-51436, Lithuania Manufacturer: UAB Teltonika Networks Address of Manufacturer: K. Barsausko st. 66, Kaunas, LT-51436, Lithuania Factory: TELTONIKA EMS UAB Address of Factory: Ditvos g. 6, LT-02121, Vilnius, Lithuania Equipment Under Test (EUT): EUT Name: Wi-Fi ACCESS POINT Model No.: TAP100 Trade Mark: TELTONIKA FCC ID: 2AET4TAP100 Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2023-06-08 Date of Evaluation: 2023-06-14 to 2023-06-21 Date of Issue: 2023-07-03 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179503 Page: 2 of 11 Revision Record Version Chapter Date Modifier Remark 01 2023-07-03 Original Authorized for issue by: Vincent Chen/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179503 Page: 3 of 11 2 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Contents .................................................................................................................................................... 3 3 General Information .................................................................................................................................. 4 3.1 General Description of E.U.T. ............................................................................................................ 4 3.2 Details of E.U.T. ................................................................................................................................. 4 3.3 Separation Distance ........................................................................................................................... 4 3.4 Test Location ...................................................................................................................................... 5 3.5 Test Facility ........................................................................................................................................ 5 3.6 Deviation from Standards ................................................................................................................... 5 3.7 Abnormalities from Standard Conditions ........................................................................................... 5 4 FCC Radiofrequency radiation exposure limits .................................................................................... 6 4.1 Blanket 1 mW Blanket Exemption ...................................................................................................... 6 4.2 MPE-based Exemption ...................................................................................................................... 6 4.3 SAR-based Exemption ....................................................................................................................... 7 5 Measurement and Calculation ............................................................................................................... 10 5.1 Maximum transmit power ................................................................................................................. 10 5.2 RF Exposure Calculation ................................................................................................................. 10 6 EUT Constructional Details (EUT Photos) ........................................................................................... 11 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179503 Page: 4 of 11 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. Power supply: Powered by PoE port (IEEE 802.3 af) DC 44-57V Cable(s): LAN cable 152cm unshielded Operation Frequency: 802.11b/g/n(HT20): 2412MHz to 2462MHz, 802.11n(HT40): 2422MHz to 2452MHz Modulation Type: 802.11b: DSSS (CCK, DQPSK, DBPSK), 802.11g/n: OFDM (64QAM, 16QAM, QPSK, BPSK) Channel Spacing: 5MHz Number of Channels: 802.11b/g/n(HT20): 11, 802.11n(HT40):7 Antenna Type: Internal Antenna Antenna Gain: Antenna 1&2: 4.9dBi Remark: The information in this section is provided by the applicant or manufacturer, SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. 3.3 Separation Distance Minimum test separation distance: 20cm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179503 Page: 5 of 11 3.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by th…

Text truncated - open the document above for the full version.

OnBoard TM SMD 2400 Datasheet Rev 1.2 2019-09-25 www.proant.se Proant AB Phone: +46 (0)90 40150 Gräddvägen 15A, 90620 Umeå, Sweden General information The OnBoard SMD 2400 antenna is a combination of small size, low cost and high performance, suitable for applications within the 2.4 GHz ISM band. Applications IoT-devices M2M-commmunications Telemetry Automated meter reading Alarms Antenna drawing. Above dimensions are given in millimeter. *Measured on Proant evaluation board, PRO-EB-450 Technical data Frequency 2400 - 2500 MHz Impedance 50 Ω Return loss* < -6.9 dB Total efficiency* > -1.9 dB (65%) Gain* Max 4.9 dBi Dimensions (LxWxH) 13.75 x 5.23 x 3.53 mm (0.541 x 0.206 x 0.139 in) RoHS status Compliant with EU directive 2011/65/EU and 2015/863 Shelf life 10 years MSL Level 1, unlimited Mechanical resistance Immunity to vibrations IEC/EN 60068-2-6, Fc test Immunity to shock IEC/EN 60068-2-27, Ea test Datasheet Page | 2 Rev 1.2 2019-09-25 www.proant.se Proant AB Phone: +46 (0)90 40150 Gräddvägen 15A, 90620 Umeå, Sweden Electrical performance Measurement setup Total radiation efficiency Maximum radiation gain The antenna measurements were done with the OnBoard SMD 2400 evaluation board (PRO-EB-450, 100 x 50 mm) - measured in free space. Return loss Datasheet Page | 3 Rev 1.2 2019-09-25 www.proant.se Proant AB Phone: +46 (0)90 40150 Gräddvägen 15A, 90620 Umeå, Sweden Radiation pattern, 2400 MHz Board rotation Datasheet Page | 4 Rev 1.2 2019-09-25 www.proant.se Proant AB Phone: +46 (0)90 40150 Gräddvägen 15A, 90620 Umeå, Sweden Radiation pattern, 2500 MHz Board rotation Datasheet Page | 5 Rev 1.2 2019-09-25 www.proant.se Proant AB Phone: +46 (0)90 40150 Gräddvägen 15A, 90620 Umeå, Sweden Intended applications The antenna is optimized for the ISM band of 2.4 GHz, which is utilized by several protocols. Some of the applications are: WLAN/Wifi IEEE 802.11 (b, g, n) 2400 - 2497 MHz Bluetooth IEEE 802.15.1 2400 - 2483.5 MHz ZigBee IEEE 802.15.4 2400 - 2483.5 MHz RFID ISO/IEC 18000 2450 MHz WirelessHART IEEE 802.15.4 2400 - 2483.5 MHz Ordering information Part number Part name Details PRO-OB-440 OnBoard SMD 2400 Antenna for 2.4 GHz ISM band. PRO-EB-450 Evaluation board, Onboard SMD 2400 Evaluation board with PRO-OB-440 for WLAN/Wifi, Bluetooth, Zigbee, RFID, WirelessHART applications. For information on sales, delivery terms and conditions and prices, please visit the Proant website (www.proant.se) for a complete list of distributors. Proant offers consultation with design-in of the OnBoard SMD antennas. Proant have all necessary capabilities for antenna design including anechoic chamber and prototype workshop. Please send your requests to [email protected]. Disclaimer The information given in this application note shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Proant AB hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179502 Page: 1 of 160 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2306001795AT Applicant: UAB Teltonika Networks Address of Applicant: K. Barsausko st. 66, Kaunas, LT-51436, Lithuania Manufacturer: UAB Teltonika Networks Address of Manufacturer: K. Barsausko st. 66, Kaunas, LT-51436, Lithuania Factory: TELTONIKA EMS UAB Address of Factory: Ditvos g. 6, LT-02121, Vilnius, Lithuania Equipment Under Test (EUT): EUT Name: Wi-Fi ACCESS POINT Model No.: TAP100 Trade Mark: TELTONIKA FCC ID: 2AET4TAP100 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2023-06-08 Date of Test: 2023-06-14 to 2023-06-21 Date of Issue: 2023-07-03 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179502 Page: 2 of 160 Revision Record Version Chapter Date Modifier Remark 01 2023-07-03 Original Authorized for issue by: Vincent Chen/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179502 Page: 3 of 160 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Conducted Peak Output Power ANSI C63.10 (2013) Section 11.9.2 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/0 Aug01,2022 Report No.: SZCR230600179502 Page: 4 of 160 3 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Test Summary ........................................................................................................................................... 3 3 Contents .................................................................................................................................................... 4 4 General Information .................................................................................................................................. 6 4.1 Details of E.U.T. ................................................................................................................................. 6 4.2 Description of Support Units .............................................................................................................. 6 4.3 Measurement Uncertainty .................................................................................................................. 6 4.4 Test Location ...................................................................................................................................... 7 4.5 Test Facility ........................................................................................................................................ 7 4.6 Deviation from Standards ................................................................................................................... 7 4.7 Abnormalities from Standard Conditions ........................................................................................... 7 5 Equipment List .......................................................................................................................................... 8 6 Radio Spectrum Technical Requirement ............................................................................................. 11 6.1 Antenna Requirement ...................................................................................................................... 11 6.1.1 Test Requirement: ....................................................................................................................... 11 6.1.2 Conclusion ................................................................................................................................... 11 7 Radio Spectrum Matter Test Results .................................................................................................... 12 7.1 Conducted Emissions at AC Power Line (150kHz-30MHz) ............................................................. 12 7.1.1 E.U.T. Operation .......................................................................................................................... 12 7.1.2 Test Mode Description ................................................................................................................. 12 7.1.3 Test Setup Diagram ..................................................................................................................... 13 7.1.4 Measurement Procedure and Data..............................................…

Text truncated - open the document above for the full version.