2AFKNPF2200ArcField Wireless Charger

1 User Manual PF2200 EN DE FR IT JP KO ES NL PL SE 234 7 89 5 111214 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including int erference that may cause undesir ed operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The following importer is the responsible party (for FCC matters only). Spigen Inc. 9975 Toledo Way #100, Irvine, CA 92618 USA E-mail : [email protected] FCC Sta tement 3MN109990 Customer Service 24-month limited warranty 24-monatige eingeschränkte Gar antie Gar antie limitée de 24 mois garanzia limitata di 24 mesi ��ヶ月保証 ��개월 제한 보증 Gar antía limitada de 24 meses Beperkte garantie van 24 maanden 24-miesięczna ograniczona gwar ancja 24 månaders begränsad garanti EN DE FR Please note that your rights under applicable law governing warranties given under this limited warranty. Ihr e Rechte gemäß dem entsprechenden Gesetz über den Verkauf von Verbrauchsgütern bleiben von der in dieser eingeschränkten Garantie angegebenen Garantie unberührt. Veuillez noter que vos droits en vertu de la loi applicable régissant la vente de biens de consommation ne sont pas limitée. IC Sta tement Thank you for your purchase ! If you have any issues or concerns, let us know at US,EU & Others: [email protected] KR: [email protected] We are Prepared and Ready to Solve Your Problems! Manufacturer : Spigen Korea Co., Ltd. Spigen ArcField Wireless Charger Instruction 1. Do not exert excess force on the product. 2. Do not disassemble the product or let it come into direct contact with heat or water. 3. Be careful when using the product in a hot or humid environment as it may damage the circuit . 4. A magnet may cause the product to break or malfunction; do not place magnetic chip card (e.g. ID cards, credit cards) near the product. 5. Medical devices (e.g. pulse measuring device, hearing aid) may indirectly interfere with the product; keep them at least 20cm away from the product. 6. Keep away from childr en. * The product image herein is provided as an example and user' s guide actual product. * For smartphones that do not support wireles s charging, you need to use a separate wireles s charging patch or wireless charging case. EN Important Safety Instructions 1. Non esercitare una forza eccessiv a sul prodotto. 2. Non smontare il prodotto o lasciarlo entrare in diretto contatto con calore o acqua. 3. Fare attenzione quando si utilizza il prodotto in un ambiente caldo o umido ambiente in quanto potrebbe danneggiare il circuit o. 4. Un magnete può causare la rottura o il malfunzionamento del prodotto; non posizionare la carta con chip magnetico (es. carte d'identità, carte di credito) vicino al prodotto. 5. Dispositivi medici (ad es. dispositivo per la misurazione del polso, apparecchio acustic o) possono interferi re indirettamente con il prodotto; tienili almeno 20 cm di distanza dal prodotto. 6. Tenere lontano dai bambini. * L'immagine del prodotto qui è fornita come esempio e guida per l'utente per il caricabatteri e wireless portatile ad alta velocità e * Per gli smartphone che non supportano la ricarica wireless, è necessario utilizzare una patch di ricarica wireless separata o custodia di ricarica wireless. IT Importante istruzioni per la sicurezza 1. N'exercez pas de force excessive sur le produit. 2. Ne démontez pas le produit et ne le laissez pas directement à la chaleur ou à l'eau. 3. Soyez prudent lorsque vous utilisez le produit dans un envir onnement chaude ou humide car cela pourrait endommager le circuit . 4. Un aimant peut provoquer la rupture ou le dysfonctionnement du produit ; ne placez pas de carte à puce magnétique (par exemple, cartes d'identité, cartes de crédit) à proximité du produit. 5. Les appareils médicaux (par exemple, appareil de mesure du pouls, appareil auditif) peuvent interférer indirectement avec le produit ; garde les à au moins 20cm du produit. 6. Tenir à l'écart des enfants. * L'image du produit sert d'exemple et de manuel d'u tili sation d'un produit réel. * Pour les smartphones qui ne suppportent pas la fonction de recharge sans fil, vous devez utiliser un patch de charge sans fil séparé ou étui de recharge sans fil. FR Instructions importantes de sécurit é 1. No ejer za una fuerza excesiva sobre el producto. 2. No desmonte el producto ni deje que entre directamente contacto con el calor o el agua. 3. Tenga cuidado al utilizar el producto en un lugar cálido o húmedo. ambiente, ya que pued…

Text truncated - open the document above for the full version.

Spigen Korea Co., Ltd. Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu, Seoul, 06153, South Korea Date: 2023-05-08 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (i) Filing SUBJECT: FCC Application for FCC ID: 2AFKNPF2200 To Whom It May Concern: Spigen Korea Co., Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signatory [Sang-Hyup Woo, Team Leader]

Spigen Korea Co., Ltd. Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu, Seoul, 06153, South Korea Date: 2023-05-08 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (ii) Filing SUBJECT: FCC Application for FCC ID: 2AFKNPF2200 To Whom It May Concern: Spigen Korea Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signatory [Sang-Hyup Woo, Team Leader]

Spigen Korea Co., Ltd. Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu, Seoul, 06153, South Korea Date: 2023-05-08 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AFKNPF2200 Spigen Korea Co., Ltd. certifies that, as of the date of the filing of the application, Spigen Inc is our designated U.S. agent for service of process for the above referenced FCC ID. Spigen Korea Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Spigen Inc accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Spigen Inc FRN: 0033411091 Address: 9975 Toledo Way, STE 100, Irvine, CA 92618, United States Contact Person: Mr Hyungjoon Kim Tel.: (949) 502-5121 Email: [email protected] Sincerely, Signed on behalf of Spigen Korea Co., Ltd. Signed on behalf of Spigen Inc. (U.S. Agent) Name: Sang-Hyup Woo Name: Hyungjoon Kim Title: Team Leader Title: Sr.Manager Date: 2023-05-08 Date: 2023-05-08

Spigen Korea Co., Ltd. Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu, Seoul, 06153, South Korea Date: 2023-05-08 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2AFKNPF2200 Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. ☒ Block Diagram ☐ Tune-Up Information ☒ Operational Description ☐ Security Information ☒ Schematics ☐ Software Defined Radio (SDR) Information ☒ Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); ☐ External Photos ☐ Test Setup Photos ☐ Internal Photos ☐ User Manual ☐ For 45 days, pursuant to Public Notice DA 04-1705. or ☐ For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signatory [Sang-Hyup Woo, Team Leader]

Spigen Korea Co., Ltd. Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu, Seoul, 06153, South Korea Date: 2023-05-08 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2AFKNPF2200 POWER OF ATTORNEY To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Spigen Korea Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Signatory [Sang-Hyup Woo, Team Leader]

Reference No.: WTX23X04075074W Page 2 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Reference No.: WTX23X04075074W Page 3 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 3 EUT View 4 Reference No.: WTX23X04075074W Page 4 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 5 EUT View 6 Reference No.: WTX23X04075074W Page 5 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 7 EUT View 8

Reference No.: WTX23X04075074W Page 1 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

Reference No.: WTX23X04075074W Page 6 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 Solder Board-Component View 1 Reference No.: WTX23X04075074W Page 7 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 2 Solder Board-Component View 3 Reference No.: WTX23X04075074W Page 8 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Antenna View

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 12 TEST REPORT Reference No. .................... : WTX23X04075074W002 FCC ID ................................ : 2AFKNPF2200 Applicant ........................... : Spigen Korea Co., Ltd. Address ............................. : Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu,Seoul, 06153, South Korea Manufacturer ..................... : The same as Applicant Address ............................. : The same as Applicant Product Name ................... : ArcField Wireless Charger Model No... ......................... : PF2200 Standards .......................... : KDB 680106 D01 V03 Date of Receipt sample .... : 2023-04-10 Date of Test........................ : 2023-04-10 to 2023-04-20 Date of Issue ..................... : 2023-04-20 Test Report Form No. ....... : WTX_KDB 680106_D01_V03W Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Mike Shi Silin Chen Reference No.: WTX23X04075074W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 12 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 AUXILIARY EQUIPMENT LIST AND DETAILS ........................................................................................................... 5 1.3 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 6 2. RF EXPOSURE TEST REPORT ............................................................................................................................ 7 2.1 STANDARD APPLICABLE ......................................................................................................................................... 7 2.2 TEST CONDITIONS .................................................................................................................................................. 7 2.3 TEST PROCEDURE ................................................................................................................................................... 8 2.4 TEST RESULT.......................................................................................................................................................... 9 2.5 MEASUREMENT UNCERTAINTY ............................................................................................................................ 10 2.6 TEST PHOTOS ....................................................................................................................................................... 11 APPENDIX PHOTOGRAPHS ................................................................................................................................... 12 Reference No.: WTX23X04075074W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 3 of 12 Report version Version No. Date of issue Description Rev.00 2023-04-20 Original / / / Reference No.: WTX23X04075074W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 4 of 12 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Factory 1#: SuiChuan CE LINK LIMITED Address of factory 1#: SuiChuan county industrial park east zone, Ji’an city, Jiang xi province, China. Factory 2#: CE LINK VIET NAM COMPANY LIMITED. Address of factory 2#: Lot CNSG04&CNSG06 Van Trung Industrial Zone, Viet Yen district, Bac Giang Province, Vietnam General Description of EUT Product Name: ArcField Wireless Charger Trade Name: Spigen Model No.: PF2200 Adding Model(s): / Battery Capacity / Note: The test data is gathered from a production sample, provided by the manufacturer. Technical Characteristics of EUT Frequency Range: 112-205kHz/ 363.26kHz Modulation Type: ASK Antenna Type: Coil Antenna Input: DC9V ⎓2.22A Wireless output： 5W/15W Adapter / Antenna Gain 0dBi Reference No.: WTX23X04075074W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 5 of 12 1.2 Auxiliary Equipment List and Details Auxiliary Equipment List and Details Description Manufacturer Model Serial Number AC Adapter / PN453C / Wireless charging tester / YBZ / EUT Cable List and Details Description Manufacturer Model Serial Number DC CABLE 2.0 Shielded Without Ferrite Reference No.: WTX23X04075074W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 6 of 12 1.3 Test Equipment List and Details Description Manufacturer Model Serial No. Cal Date Due Date ELECTRIC AND MAGNETIC FIELD ANALYZER Narda EHP-200AC 180ZX10226 2021-05-20 2024-05-19 Note: The deviation response is 0.8dB. Reference No.: WTX23X04075074W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 7 of 12 2. RF Exposure Test Report 2.1 Standard Applicable According to§1.1310 system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. 2.2 Test Conditions Test Mode Description Remark Power Supply Mode TM1 Wireless charging (112-205kHz) Wireless output(5W) / TM2 Wireless charging (363.26kHz) Wireless output(15W) / No…

Text truncated - open the document above for the full version.

Specification for power supply REV：1.1 MODEL NO. : DATE：2022-11-05 PAGE： 1 / 2 SPECIFICATION FOR APPROVAL CUSTOMER : Spigen Korea Co., Ltd. CUSTOMER NO: MODEL NO: PF2200 APPROVAL REV: V1.0 DATE: 2022-11-05 Please return to us on copy of “SPECIFICATION FOR APPROVAL” With your approved signature Hinen Electronics (Shenzhen) Co. Ltd 3/F Building C, Li Cheng Tech. Ind. Zone Gong he Village, Sha Jing Town, Shenzhen City, China TEL: 0755--29519374 / 26639997 FAX: 0755--29519395 DRAFTED CHECKED APPROVED CUSTOMER AUTHORIZED SIGNATURE TESTED BY CHECKED APPROVED Specification for power supply REV：1.1 MODEL NO. : DATE：2022-11-05 PAGE： 2 / 2 coil’s Size(Unit: mm)

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 30 TEST REPORT Reference No. .................... : WTX23X04075074W001 FCC ID ................................ : 2AFKNPF2200 Applicant ........................... : Spigen Korea Co., Ltd. Address ............................. : Spigen HQ-A, 446, Bongeunsa-ro, Gangnam-gu,Seoul, 06153, South Korea Manufacturer ..................... : The same as Applicant Address ............................. : The same as Applicant Product Name ................... : ArcField Wireless Charger Model No... ......................... : PF2200 Standards .......................... : FCC Part 15C Date of Receipt sample .... : 2023-04-10 Date of Test........................ : 2023-04-10 to 2023-04-20 Date of Issue ..................... : 2023-04-20 Test Report Form No. ....... : WTX_Part 15_207_209W Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Mike Shi Silin Chen Reference No.: WTX23X04075074W001 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 30 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ......................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................. 5 1.3 TEST METHODOLOGY ........................................................................................................................................... 5 1.4 TEST FACILITY ...................................................................................................................................................... 5 1.5 EUT SETUP AND OPERATION MODE ................................................................................................................... 6 1.6 MEASUREMENT UNCERTAINTY ............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 11 3. RF EXPOSURE ...................................................................................................................................................... 12 3.1 STANDARD APPLICABLE ..................................................................................................................................... 12 3.2 TEST RESULT ...................................................................................................................................................... 12 4. ANTENNA REQUIREMENT ................................................................................................................................. 13 4.1 STANDARD APPLICABLE ..................................................................................................................................... 13 4.2 TEST RESULT ...................................................................................................................................................... 13 5. CONDUCTED EMISSIONS .................................................................................................................................. 14 5.1 TEST PROCEDURE .............................................................................................................................................. 14 5.2 BASIC TEST SETUP BLOCK DIAGRAM ................................................................................................................ 14 5.3 ENVIRONMENTAL CONDITIONS ........................................................................................................................... 14 5.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 14 6. RADIATED EMISSION .......................................................................................................................................... 19 6.1 STANDARD APPLICABLE ..................................................................................................................................... 19 6.2 TEST PROCEDURE .............................................................................................................................................. 19 6.3 TEST RECEIVER SETUP ...................................................................................................................................... 20 6.4 CORRECTED AMPLITUDE & MARGIN CALCULATION ........................................................................................... 20 6.5 ENVIRONMENTAL CONDITIONS ........................................................................................................................... 21 6.6 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 21 7. OCCUPIED BANDWIDTH .................................................................................…

Text truncated - open the document above for the full version.

Reference No.: WTX23X04075074W Page 9 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Conducted Emission Test Setup Radiation Emission Test Setup (Below 30MHz) Reference No.: WTX23X04075074W Page 10 of 10 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Radiation Emission Test Setup (30MHz to 1GHz) ***** END OF REPORT *****