2AG7TENVV00015Wireless Siren

Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Limited Warranty Envisacor guarantees that every wireless siren & strobe alarm is free from physical defects in material and workmanship under normal usage for one year from the date of installation. If the product proves defective during this one-year warranty period, Envisacor will replace it free of charge. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent usage; (2) units which have been repaired, taken apart, or modified by a unauthorized personnel; (3) units not used in accordance with instruction; (4) damages exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. HM1601 V0 1091103 6B1H-16UC 1 Installation & Operation Manual HM1601 Wireless Siren -3 - Introduction Thanks for choosing the HM1601 wireless siren and strobe for the SOLO wireless security system. This device extends the audio and visual alarm notifications of the SOLO base station to anywhere in your home. You can add up to four (4) HM1601s to a single SOLO base station. The HM1601 provides separate visual and audio notifications for burglary, fire, waterflow, and personal medical alarms. The HM1601 is fully supervised and includes low-battery notifications, wirelessly. Product Description and Specification *** For indoor use only *** Specification: Package Content: Frequency Range: 433.92Mhz 1pc HM1601 Siren Operating Range: Up to 30m (100 ft) line of 1pc Adhesive tape sight 2pcs Screw Loud Audible Alarm: > 105Db@1m 4pcs AA Energizer Batteries LED Strobe Lighting: 4 x LED lights 1pc Installation & Operation Operating Temp.: -15°C~ 60°C (5°F~140°F) Manual Battery: 4pcs x AA Energizer Batteries Installation 1. Remove the bracket from the siren by pressing the locking tab, and then gently slide up the receiver housing. Observe the correct polarity before insert the batteries. 2. After insert the batteries, the LED will flash 5 times. 3. Enroll the HM1601 with the SOLO base station either using the auto-enrolment feature, or by noting the 6-digit wireless ID on the back of the HM1601 for manual enrolment. For more information about enrolling wireless devices on your SOLO system, please refer to your SOLO documentation. If enrolling manually, make sure you select “Remote Siren” as the wireless zone definition. -1- 4. For automatic enrollment, place the SOLO base station in auto-learn mode. When in auto-learn, depress the tamper/program switch until you hear three acknowledgment beeps from the base station. A long tone indicates the HM1601 is already enrolled. 5. Once enrolled, temporarily place the siren in the proposed location and perform a base station Walk Test. If successful, then proceed to step 6. If the location does no provide adequate signal strength, re-locate and do the Walk Test again. 6. Using the screws or adhesive tape to fix the bracket in the required location. 7. Once the bracket is secured, slide the siren back into the bracket. Operation 1. The HM1601 will respond to wireless alarm commands from the SOLO base station. Depending on the type of alarm, the HM1601 will issue audible alarms with different cadences. The strobe light will also flash to indicate an alarm condition The duration alarm time depends on the Bell-Timeout (BTO) settings within the SOLO. In the event of loss of communications with the SOLO base station, the HM1601 will automatically silence the alarm after 10 minutes. 2. The HM1601 is fully supervised with the SOLO base station. If communications are lost with the HM1601, the SOLO base station will flag a supervisory fault. 3. HM1601 equipped with tamper switch. If the siren is removed from bracket, it will report to the base station. 4. If the HM1601 is in the low-battery state, the strobe light will flash every 10 seconds and notify the SOLO base station. Please change the batteries immediately. -2-

Applicant Declaration Applicant Declaration Rev:0. 0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Envisacor Technologies Inc. Address 726319 Sideroad 22B, RR4 Meaford, N4L 1W7, Canada Grantee Code 2AG7T FCC ID 2AG7TENVV00015 Authorized Contact Name Mr Andrew M Cullen Contact Email [email protected] Contact Phone +1 (647) 503-3400 ext 408 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: November 18, 2020 Print Name: Andrew M. Cullen P.Eng. Title: VP Engineering *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Envisacor Technologies Incorporated 726319 Sideroad 22B, RR4 Meaford Ontaio, N4L 1W7, Canada Date: January 5, 2021 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AG7TENVV00015 To whom it may concern: We, the undersigned, hereby authorize Ms. Daphne Liang / Section Manager of SGS Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Envisacor Technologies Inc. This authorization is valid until further written notice from the applicant. Name: Andrew M. Cullen P.Eng. Title: Vice-President Engineering Signature: On behalf of Company: Envisacor Technologies Inc. Telephone: +1 (647) 503-3400

November 18 th ,2020 Envisacor Technologies Inc. 726319 Sideroad 22B, RR4 Meaford Ontaio, N4L 1W7, Canada To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Envisacor Technologies Inc. 726319 Sideroad 22B, RR4 Meaford Ontaio, N4L 1W7, Canada Regarding: Confidentiality Request regarding application for FCC ID: 2AG7TENVV00015 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Andrew M. Cullen P.Eng. VP Engineering Envisacor Technologies Inc.

Page 1 / 8 Report No.: T201116N02 Ref. No.: Rev. 00 External Photo (Model: HM1601) Page 2 / 8 Report No.: T201116N02 Ref. No.: Rev. 00

Label location Model: HM1601 IC: 5857A- ENVV00015 FCC ID:2AG7TENVV00015 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Page 3 / 8 Report No.: T201116N02 Ref. No.: Rev. 00 Internal Photo (Model: HM1601) Page 4 / 8 Report No.: T201116N02 Ref. No.: Rev. 00 Page 5 / 8 Report No.: T201116N02 Ref. No.: Rev. 00 Page 6 / 8 Report No.: T201116N02 Ref. No.: Rev. 00 Page 7 / 8 Report No.: T201116N02 Ref. No.: Rev. 00 Page 8 / 8 Report No.: T201116N02 Ref. No.: Rev. 00

FCC ID: 2AG7TENVV00015 Page: 1 / 39 Report No.: T201116N02-RP1 Rev.: 00 No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan /8 t:(886-6) 5802-201 f:(886-6) 5802-202 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. Member of the SGS Group FCC 47 CFR PART 15 SUBPART C ANSI C63.10: 2013 TEST REPORT For Wireless Siren Model: HM1601 Data Applies To: N/A Brand: Test Report Number: T201116N02-RP1 Issued to Envisacor Technologies Incorporated 726319 Sideroad 22B RR4 Meaford Canada N4L 1W7 Issued by Compliance Certification Services Inc. Tainan Lab. No.8, Jiucengling, Xinhua Dist., Tainan Cit y , Taiwan Issued Date: January 05, 2021 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page: 2 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 January 05, 2021 Initial Issue ALL Polly Wang 01 August 28, 2020 See the following note rev.01 Page 6 Gina Lin 02 September10, 2018 See the following note rev.02 ALL Gina Lin Note: Rev.01 Issue Date August 28, 2020 Revise Operation Frequency. Rev.02 Issue Date September 10, 2018 Update test result summary. Page: 3 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ........................................................................ 4 2. TEST RESULT SUMMARY ................................................................................. 5 3. EUT DESCRIPTION ............................................................................................. 6 4. TEST METHODOLOGY ....................................................................................... 7 4.1 EUT CONFIGURATION ............................................................................... 7 4.2 EUT EXERCISE ........................................................................................... 7 4.3 GENERAL TEST PROCEDURES ................................................................ 7 4.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .................... 8 4.5 DESCRIPTION OF TEST MODES ............................................................... 8 5. INSTRUMENT CALIBRATION ............................................................................ 9 5.1 MEASURING INSTRUMENT CALIBRATION ............................................... 9 5.2 MEASUREMENT EQUIPMENT USED ......................................................... 9 5.3 MEASUREMENT UNCERTAINTY ............................................................. 10 6. FACILITIES AND ACCREDITATIONS .............................................................. 11 6.1 FACILITIES................................................................................................. 11 6.2 EQUIPMENT .............................................................................................. 11 6.3 TABLE OF ACCREDITATIONS AND LISTINGS ........................................ 11 6.4 TABLE OF ACCREDITATIONS AND LISTINGS ........................................ 12 7. SETUP OF EQUIPMENT UNDER TEST ........................................................... 13 7.1 SETUP CONFIGURATION OF EUT ........................................................... 13 7.2 SUPPORT EQUIPMENT ............................................................................ 13 7.3 EUT OPERATING CONDITION ................................................................. 13 8. FCC PART 15.231 REQUIREMENTS ................................................................ 14 8.1 99% BANDWIDTH ...................................................................................... 14 8.2 20dB BANDWIDTH ..................................................................................... 16 8.3 LIMIT OF TRANSMISSION TIME ............................................................... 18 8.4 DUTY CYCLE ............................................................................................. 20 8.5 RADIATED EMISSIONS ............................................................................. 24 8.6 POWERLINE CONDUCTED EMISSIONS ................................................. 35 9. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ............................................ 36 Page: 4 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00 1. TEST RESULT CERTIFICATION Product: Wireless Siren Model: HM1601 Data Applies To: N/A Brand Name: Applicant: Envisacor Technologies Incorporated 726319 Sideroad 22B RR4 Meaford Canada N4L 1W7 Manufacturer: Vision Automobile Electronics Industrial Co Ltd. N…

Text truncated - open the document above for the full version.

Page: 36 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00 9. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION MEASUREMENT SETUP Below 1GHz Page: 37 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00 Page: 38 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00 RADIATED RF MEASUREMENT SETUP Above 1GHz Page: 39 / 39 Report No.: T201116N02-RP1 Ref. No.: Rev.: 00