2AG7TENVV00016Wireless Smoke Sensor

Introduction The HS6101 is a supervised, wireless, Smoke Sensor for use with SOLO Security and PERS systems. If the sensor detects a certain density of smoke then the built in siren will sound and a signal will be sent to the SOLO base unit. Please refer to the SOLO installation guide for further information. Product Description and Specification Figure 1: *** For indoor use only *** Tamper Switch Specification: Package Content: Frequency Range: 433.92Mhz 1pc HS 6101/HS 6101-A Operating Range: 33m (100 ft) line of sight 1pc Smoke Sensor Operating Temp.: -10°C~ 50°C (14°F~122°F) Bracket Holder Battery: Panasonic CR123A * 1PC 1pc Plastic Anchor & 2pcs Screw 1pc CR123A Lithium Battery 1pc Installation & Operation Manual Installation 1. Find a suitable location to mount the detector. See Figure 2 (opposite). 2. Open the battery cover to insert the battery. 3. Enroll and complete the placement test as per your SOLO instructions. Confirm that the installation location is within suitable RF range of the SOLO base station before proceeding. 4. Remove the bracket from the detector by rotating it counter-clockwise. 5. Place the bracket where you are going to install the detector. In each of the key hole slots, draw a mark to locate plastic anchor and screw. Using a 3/16-inch (5mm) drill bit, drills two holes at the marks and insert plastic anchor, and attached the bracket by using the screws. 6. Install the detector into the bracket by rotating it clockwise. -1- Figure 2: Suggested Locations for Installation: -2- -2- Install second-floor alarms at the top of first-to-second floor stairwell. Install basement alarms at the bottom of the basement stairwell. Operation 1. Stand-by Mode: The Red LED flashes one time every 6 minutes. 2. Alarm Mode (The status when the alarm is triggered.): If a certain density of smoke is detected, an audible alarm with 3 beeps will occur. The red LED will flash continuously and rapidly and the detector will send an alarm condition to the SOLO base. 3. Error Mode: If the detector beeps and the yellow LED flashes three times every 43 seconds, it indicates the Smoke Sensor is not working properly. Repair or service is required. 4. Low Battery Warning Mode: The yellow LED will flash once every 43 seconds with a short “beep” sound and a low-battery report will be issued to the SOLO base. The battery will need to be changed to reset this warning. 5. Test Mode: After inserting the battery, push the test switch for about 3 seconds to enter test mode. The red LED will flash once every 11 seconds. The detector will quit test mode after 10 minutes or when the test switch is pushed again. 6. Tamper Mode: 1) If the detector is removed from the bracket, the yellow LED will light solid and the unit will emit a continuous alarm until it is mounted back on the bracket. 2) On installation the detector should be mounted on the bracket within 3 minutes to avoid triggering the tamper mode. 7. Silent Mode: When the detector is in alarm, the user can press the test switch to enter silent mode and disable the alarm temporarily. The red LED light will still flash continuously. The silent function will automatically return to normal operation if the smoke concentration around the detector is still at or above alarm level after 10 minutes of silent mode. -2- Federal Communications Commission Statement This equipment has been followed and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IC Statement This class [B] digital apparatus complies with Canadian ICES-003. This device complies with RSS-210 and ICES-003 of the Industry Canada Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of this device. Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Limited Warranty Envisacor Guarantees that every wireless Smoke Sensor is free from physical defects in material and workmanship under normal usage for one year from the date of purchase. If the product proves defective during this one-year warranty period, Envisacor will replace …

Text truncated - open the document above for the full version.

Applicant Declaration Applicant Declaration Rev:0. 0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Envisacor Technologies Inc. Address 726319 Sideroad 22B, RR4 Meaford, N4L 1W7, Canada Grantee Code 2AG7T FCC ID 2AG7TENVV00016 Authorized Contact Name Mr Andrew M Cullen Contact Email [email protected] Contact Phone +1 (647) 503-3400 ext 408 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: January 8, 2021 Print Name: Andrew M. Cullen P.Eng. Title: VP Engineering *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Envisacor Technologies Incorporated 726319 Sideroad 22B, RR4 Meaford , N4L 1W7, Canada Date: February 9, 2021 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AG7TENVV00016 To whom it may concern: We, the undersigned, hereby authorize Ms. Daphne Liang / Section Manager of SGS Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Envisacor Technologies Inc. This authorization is valid until further written notice from the applicant. Name: Andrew M. Cullen P.Eng. Title: Vice-President Engineering Signature: On behalf of Company: Envisacor Technologies Inc. Telephone: +1 (647) 503-3400

January 8, 2021 Envisacor Technologies Inc. 726319 Sideroad 22B, RR4 Meaford , N4L 1W7, Canada To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Envisacor Technologies Inc. 726319 Sideroad 22B, RR4 Meaford , N4L 1W7, Canada Regarding: Confidentiality Request regarding application for FCC ID: 2AG7TENVV00016 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Andrew M. Cullen P.Eng. VP Engineering Envisacor Technologies Inc.

Page 1 / 6 Report No.: T210119N03 Ref. No.: Rev. 00 External Photo (Model: HS6101)

HS6101 Diagram Label location Label location

Wireless Smoke Detector Détecteur de fumée sans l Detector de humo inalámbrico This devic e c omplies with P ar t 15 of the FC C Rules . Operation is subjec t t o the f ollo wing t wo c onditions: (1) This devic e ma y not cause har mful in ter fer enc e, and (2) This devic e must accept an y in ter fer enc e rec eiv ed , including in ter fer enc e tha t ma y cause undesir ed oper ation. Cet appar eil est c onf or me à la par te 15 de la r églemen ta tion FC C. appar eil ne doit pas pr ovoquer d ’in ter fér enc es néfast es , et 2) c et appar eil doit t olér er les in ter fér enc es r eçues , y c ompr is c elles qui risquen t de pr ovoquer un f onc tionnemen t indésir able . Est e dispositiv o cumple c on la disposición 15 de la Nor ma tiv a FC C. El funciona- mien to está sujet o a las siguien tes dos c ondiciones: (1) est e dispositiv o no debe causar in ter fer encias dañinas , y (2) est e dispositiv o debe ac eptar cualquier in ter fer encia r ecibida, incluy endo aquellas in ter fer encias que pudier an causar un funcionamien to no deseado . Model: HS6101 Made in Taiwan Conçu au Taiwan Fabricado en Taiwán FCC ID: 2AG7TENVV00016

Page 2 / 6 Report No.: T210119N03 Ref. No.: Rev. 00 Internal Photo (Model: HS6101) Page 3 / 6 Report No.: T210119N03 Ref. No.: Rev. 00 Page 4 / 6 Report No.: T210119N03 Ref. No.: Rev. 00 Page 5 / 6 Report No.: T210119N03 Ref. No.: Rev. 00 Page 6 / 6 Report No.: T210119N03 Ref. No.: Rev. 00

FCC ID: 2AG7TENVV00016Page: 1 / 39 Report No.: T210119N03-RP1 Rev.:01 No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan /8 t:(886-6) 5802-201 f:(886-6) 5802-202 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. Member of the SGS Group FCC 47 CFR P ART 15 SUBPART C ANSI C63.10: 2013 TEST REPORT For Wireless Smoke Sensor Model: HS6101 Data Applies To: N/A Brand: Test Report Number: T210119N03-RP1 Issued to Envisacor Technologies Incorporated 726319 Sideroad 22B RR4 Meaford Canada N4L 1W7 Issued by Compliance Certification Services Inc. Tainan Lab. No.8, Jiucengling, Xinhua Dist., Tainan Cit y , Taiwan Issued Date: March 02, 2021 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page: 2 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 01 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 February 23, 2021 Initial Issue ALL Gina Lin 01 March 02, 2021 See the following note rev.01 Page 6 Gina Lin 02 September10, 2018 See the following note rev.02 ALL Gina Lin Note: Rev.01 Issue Date: March 02, 2021 Update EUT DESCRIPTION. Rev.02 Issue Date September 10, 2018 Update test result summary. Page: 3 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 01 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ........................................................................ 4 2. TEST RESULT SUMMARY ................................................................................. 5 3. EUT DESCRIPTION ............................................................................................. 6 4. TEST METHODOLOGY ....................................................................................... 7 4.1 EUT CONFIGURATION ............................................................................... 7 4.2 EUT EXERCISE ........................................................................................... 7 4.3 GENERAL TEST PROCEDURES ................................................................ 7 4.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .................... 8 4.5 DESCRIPTION OF TEST MODES ............................................................... 8 5. INSTRUMENT CALIBRATION ............................................................................ 9 5.1 MEASURING INSTRUMENT CALIBRATION ............................................... 9 5.2 MEASUREMENT EQUIPMENT USED ......................................................... 9 5.3 MEASUREMENT UNCERTAINTY ............................................................. 10 6. FACILITIES AND ACCREDITATIONS .............................................................. 11 6.1 FACILITIES................................................................................................. 11 6.2 EQUIPMENT .............................................................................................. 11 6.3 TABLE OF ACCREDITATIONS AND LISTINGS ........................................ 11 6.4 TABLE OF ACCREDITATIONS AND LISTINGS ........................................ 12 7. SETUP OF EQUIPMENT UNDER TEST ........................................................... 13 7.1 SETUP CONFIGURATION OF EUT ........................................................... 13 7.2 SUPPORT EQUIPMENT ............................................................................ 13 7.3 EUT OPERATING CONDITION ................................................................. 13 8. FCC PART 15.231 REQUIREMENTS ................................................................ 14 8.1 99% BANDWIDTH ...................................................................................... 14 8.2 20dB BANDWIDTH ..................................................................................... 16 8.3 LIMIT OF TRANSMISSION TIME ............................................................... 18 8.4 DUTY CYCLE ............................................................................................. 20 8.5 RADIATED EMISSIONS ............................................................................. 24 8.6 POWERLINE CONDUCTED EMISSIONS ................................................. 35 9. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ............................................ 36 Page: 4 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 01 1. TEST RESULT CERTIFICATION Product: Wireless Smoke Sensor Model: HS6101 Data Applies To: N/A Brand Name: Applicant: Envisacor Technologies Incorporated 726319 Sideroad 22B RR4 Meaford Canada N4L 1W7 Manufacturer: Vision Automobile Electronics Industrial Co L…

Text truncated - open the document above for the full version.

Page: 36 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 00 9. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION MEASUREMENT SETUP Below 1GHz Page: 37 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 00 Page: 38 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 00 RADIATED RF MEASUREMENT SETUP Above 1GHz Page: 39 / 39 Report No.: T210119N03-RP1 Ref. No.: Rev.: 00