2AGJ5ZJ-W5Base Station Unit

Important Instructions of Safety 1. Before installing and using the device, please read this carefully for safe operation. 2. Please keep this safety operation guide for later reference 3. Please observe the matter of ‘warning’ mentioned in this operation guide for all equipment 4. must comply with the principles and regulation of this operation guide 5. Equipments cleaning: before cleaning the devices, please turn the power off, and get all connections of the system components disconnected , wipe with a dry soft cloth when cleaning 6. Strongly recommend that don’t use any mismatched accessories , Risks or problems might be caused by this 7., keep the devices far away from water or heat source to avoid potential damages. 8. Do not place the equipment on an unstable surface; Please select suitable packaging or use the original packaging before shipping to avoid equipment damage caused by strong vibration 9. A good air condition is need to extend the life of equipment. 10. voltage supply: Americas,Japan: AC 110V~120 V 60 Hz Eurasia: AC 220V~240 v 50 Hz 11. power supply plug: three pin earthed plug 12. the extension cables are essential to connect the devices, do not squeeze heavily, please find another layout When needed to keep systems running healthy. 13. In a system , the Connection of Conference units have to be according to the requirements of this system, otherwise may cause the entire system not working properly. if you have special requests ,please get in touch with GONSIN after-sales service center, The technical support phone: 0757-22360959. 14. without our permission, do not open the device body, or permeate any substances into the body such as rigid conductors or liquid residues. 15. if the equipments need maintenance, do not disassemble at once, please get in touch with Gonsin after-sales service center, hotline: 400-883-1138. 16. all GONSIN Products are maintenance guaranteed with the warranty card by system categories, but for the Force majeure or deliberate damage are not including , such as: A. broken caused by human being ; B. damage due to improper operation from the operator; C. parts damage or lost by self disassemble D. broken because of natural disasters . 17. use specified cables to connect devices. 18. turn off the power when the system is not in use for a long time, even better to unplug the power . 19. After you receive the goods, please keep the attached warranty card ,in order to provide a basis for the warranty issue later. Due to space limitation, this tag appears in the rear side of the device. The lightning mark is a reminder for users there un-insulated voltages are dangerous to lead electric shocks at inner devices. The exclamation point within these equilateral triangle, is to remind users to be with the device operation guide and maintenance instructions for operating and maintenance. Note: A qualified electrical service personnel of operating is needed for equipments installation. Unplug the power: Regardless of whether the device has a power switch, when the power cord plugs into the socket of power supply. However, only when the switch button to hit the ‘open’ position, the device can be operated. The power cord is the main wire. to 第 2 页 共 21 页 WARNING: To avoid an electrical shock, do not open the machine cover. Before connecting , operating, or testing products, please read this manual. WARNING: To avoid fire and electric shock, do not expose equipments to rain or humid Environment. 第 3 页 共 21 页 cut off all units Precautions of Lithium battery using When you find uncommon signs such as following during battery using, please turn off the power switch immediately, remove the battery and let it away from sources of fire, or may cause fire disaster or explosion. - there are signs of leakage, discoloration, deformation or damage about the battery - smoke or odor from Battery . Do not weld, reform batteries or make it deformed, by doing this may break the battery protection circuit, leading the battery to fire, leak or explode. Do not use wire or other metal objects to connect the positive pole and the negative pole of a battery , Do not store or ship the batteries with metal objects (such as necklaces or key), otherwise these may cause the batteries to fire, explode, leak, or overheat . Do not heat batteries or drop the batteries into fire, otherwise The gas safety valve or protecting electrical circuits, may be ruined causing the battery to fire or explode. Do not place the batteries in water or make the batteries poles wet , otherwise the batteries might be corrosion, and my cause to fire, explode, leak, or overheat.. When Charging the battery, make sue to match the proper charging case , and to avoid the reverse of battery positive and negative poles, if so, fire, explosion, leakage or overheating may happen . Do not place the battery near a fire source, or place it in an environment that over 60 °C (such as inner space of vehicle with direct sunlight), otherwise it may break the battery protection circuit, causing the battery to fire, explode, leak or overheat. Keep the battery used to specify model(s), Otherwise it may cause the battery to fire, explode, leak, or overheat. Do not let battery drop or vibrate severely , Otherwise it may cause the battery to fire, explose, leak, or overheat. If the liquid of battery leakage splashes into the eyes accidentally, it may cause sights blurred , please rinse with clean water and seek for medical attention immediately. If the liquid of battery leakage splashes on clothes or skin, it may damage the skin, Please rinse with clean water. Long-term idle of Lithium battery and low level of battery will damage the battery, Please remove and store the lithium battery separately, and ensure to charge the battery to saturation at least three months. Remarks: GONSIN Company reserves all rights to adjust data and without prior notice. To obtain more information in details, Please contact with your local GONSIN after-sa…

Text truncated - open the document above for the full version.

Differences Description We Gonsin Conference Equipment Co., Ltd state: Product name: Base Station Unit Model: ZJ-W5, ZJ-W3 All model’s electrically identical, the function, software and electric circuit are the same, only different in Model Name. Signature: 2015-11-23 Name Liu Jiwu Position Manager Company Name Gonsin Conference Equipment Co., Ltd Address No.401-406, Block C, Idea Industry Park, No.41 Fengxiang Road, Shunde, Foshan, Guangdong, China Tel 0757‐22360953 Fax 0757‐22382396 Email [email protected]

Nov.-22-15 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AGJ5ZJ-W5 Product Name: Base Station Unit Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics Long-term confidential • Block diagram Long-term confidential • Operation description Long-term confidential These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature: Name Liu Jiwu Position Manager Company Name Gonsin Conference Equipment Co., Ltd Address No.401-406, Block C, Idea Industry Park, No.41 Fengxiang Road, Shunde, Foshan, Guangdong, China Tel 0757‐22360953 Fax 0757‐22382396 Email [email protected]

Label 30mm 15mm Label FCC ID: 2AGJ5ZJ-W5 Gonsin Conference Equipment Co., Ltd Model name: Base Station Unit Model No.: ZJ‐W5 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Page 1 of 39 Report No.: T1851674 01 TEST REPORT FCC ID: 2AGJ5ZJ-W5 Applicant : Gonsin Conference Equipment Co., Ltd Address : No.401-406,Block C, Idea Industry Park, No.41 Fengxiang Road, Shunde, Foshan, Guangdong, China Equipment Under Test (EUT): Name : Base Station Unit Model : ZJ-W5, ZJ-W3 In Accordance with: FCC PART 15, SUBPART C : 2015 (Section 15.231) Report No: T1851674 01 Date of Test : November 13-18, 2015 Date of Issue : November 18, 2015 Test Result: PASS In the configuration tested, the EUT complied with the standards specified above Authorized Signature ___________________________ (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Alpha Product Testing Co., Ltd Or test done by Shenzhen Alpha Product Testing Co., Ltd Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Alpha Product Testing Co., Ltd Approvals in writing . Page 2 of 39 Report No.: T1851674 01 Contents 1.General Information ............................................................................................................... 3 1.1.Description of Device (EUT) ...............................................................................3 1.2.Accessories of device (EUT) ...............................................................................4 1.3.Test Lab information ............................................................................................4 2.Summary of test ...................................................................................................................... 5 2.1.Summary of test result .........................................................................................5 Occupied bandwidth ....................................................................................................................... 5 2.2.Assistant equipment used for test .........................................................................5 2.3.Block Diagram .....................................................................................................6 2.4.Test mode .............................................................................................................7 2.5.Test Conditions .....................................................................................................8 2.6.Measurement Uncertainty (95% confidence levels, k=2) ....................................8 2.7.Test Equipment .....................................................................................................9 3.Radiation Emission ............................................................................................................... 10 3.1.Radiation Emission Limits(15.209&231) ..........................................................10 3.2.Test Setup ...........................................................................................................10 3.3.Test Procedure ....................................................................................................12 3.4.Test Equipment Setting For emission test. .........................................................13 3.5.Test Condition ....................................................................................................13 3.6.Test Result ..........................................................................................................13 4.POWER LINE CONDUCTED EMISSION ....................................................................... 23 4.1.Conducted Emission Limits(15.209) .................................................................23 4.2.Test Setup ...........................................................................................................23 4.3.Test Procedure ....................................................................................................24 4.4.Test Results ........................................................................................................24 5.Occupied bandwidth ............................................................................................................. 27 5.1.Test limit .............................................................................................................27 5.2.Method of measurement .....................................................................................27 5.3.Test Setup ...........................................................................................................27 5.4.Test Results ........................................................................................................27 6.Transmission time ................................................................................................................. 30 6.1.Test limit .............................................................................................................30 6.2.Method of measurement .....................................................................................30 6.3.Test Setup ...........................................................................................................30 6.4.Test Results ........................................................................................................31 7.Antenna Requirement .......................................................................................................... 32 7.1.Standard Requirement ........................................................................................32 7.2.Antenna Connected Construction ......................................................................32 7.3.Result .....................…

Text truncated - open the document above for the full version.

Photos of Radiated emission Photos of Conducted Emission test