2AGNTNESTNest

1 Nest user manual 2 Overview of Nest Nest is an image transmission module with WIFI, Ethernet and RTK module designed and manufactured by Autel Robotics LTD., CO. The module is developed based on the LTE technology platform and is suitable for point-to-point image and data bidirectional transmission. The module provides the function of automatically and manually selecting frequency bands, and has super anti-interference ability. Characteristics Single power supply, wide voltage input USB+2 serial ports Support four-frequency automatic selection, adaptive frequency point Support wireless upgrade Automatic network repair Encrypted transmission Full industrial grade components to meet the harsh working environment Product size is small and easy to integrate Specification Parameter Description Comments System Linux/Android eMMC/Flash 32GB+24Gb Image transmission Frequency 900MHz：902-928MHz 2.4GHz：2400-2483.5MHz 5.2GHz: 5150-5250MHz 5.8GHz：5725-5850MHz 1. Work in one frequency band and frequency at the same time. 2. Can manually set frequency point. image transmission Bandwidth 1.4MHz/10MHz/20MHz WIFI 2400-2483.5MHz, 802.11a/b/g/n/ac 3 5180-5240MHz, 5725-5850MHz RTK BDS B1I/B2I/B3I/B1C/B2a/B2b GPS L1/L2/L5 GLONASS L1/L2 Galileo E1/ E5a/E5b/E6 1559-1610MHz receive function Connector/Definition A2512WR-4P： UARTx1，Baud rate：115200 DC Power 12-36V 26V typ. Power Consumption ≤8W@FCC Work Temperature Humidity -30°C~60°C 99% No condensation Storage Temperature -40°C~85°C 4 Installation The Module use for connect to the drone and remote control, it can make the drone land precisely on the tarmac. The module is installed in the control center area of EVO Nest, the module connects to the EVO Nest air conditioner, tarmac, charging pole, and control by the skylink app. Below is the EVO Nest Nest image transmission module 5 Antenna info. 1. 2.4G&5GWIFI ANT 2. 900M/2.4G/5G PCB TX&RX ANT2 3. 900M/2.4G/5G PCB RX ANT2 4. 900M/2.4G/5G External ANT2 5. 900M/2.4G/5G PCB RX ANT1 6. 900M/2.4G/5G PCB TX&RX ANT1 7. 900M/2.4G/5G External ANT1 8. GNSS ANT 1 2 3 4 5 6 7 8 6 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15 Subpart C 15.247 & 15.407 & 15.207 & 15.209 2.3 Specific operational use conditions The module is a Nest with WiFi 2.4GHz, WiFi 5GHz, SRD 5.2G/5.8GHz function. The EUT has one PCB antenna, the antenna cannot be replaced by other authorized antennas, and the gain of each replacement antenna is no more than 1dBi. This device is to be used only for mobile and fixed applications. This module can only be used with the antenna design in strict compliance with the OEM instructions provided. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. 2.4 Limited module procedures Not applicable. The module is a Single module and complies with the requirement of FCC Part 15.212. 7 2.5 Trace antenna designs Not applicable. The module has its own antenna, and doesn’t need a host’s printed board microstrip trace antenna etc. 2.6 RF exposure considerations The module must be installed in the host equipment such that at least 20cm is maintained between the antenna and users’ body; and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 2.7 Antennas The module has its own antennas are as follows: No. Antenna Antenna Type Frequency Range Antenna Gain 1 WiFi ANT FPC Antenna 2412MHz-2462MHz 6.7dBi (Max.) 5180MHz-5240MHz 4.0dBi (Max.) 5745MHz-5825MHz 4.0dBi (Max.) 2 900M/2.4G/5G PCB TX&RX ANT2 PCB Antenna 904MHz-926MHz 3.1dBi (Max.) 2403.5MHz-2471.5MHz 3.3dBi (Max.) 5154MHz-5246MHz 3.0dBi (Max.) 5728MHz-5847MHz 3.0dBi (Max.) 3 900M/2.4G/5G …

Text truncated - open the document above for the full version.

C566091_X23_Ed2 1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: Autel Robotics USA LLC FRN: 0033458068 Contact Name:Mr Jimmy Guo Address: 22522 29TH DR SE 101 Bothell, WA 98021 United States Telephone： （866）692-8835 Email: [email protected] This letter is to confirm that the US Agent for Service of Process accepts responsibility to act as a local representative on behalf of (Autel Robotics Co., Ltd.). The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Applicant: Company name: Autel Robotics Co., Ltd. Product Description: Nest Grantee code: 2AGNT FCC ID:2AGNTNEST Contact Name: Xiangxi Pan Address:601,701,801,901, Block B1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan District Shenzhen, GuangDong, 518055, China Telephone No: 86-18926791906 Email:[email protected] The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2023/08/15 Applicant’s Name: Autel Robotics Co., Ltd. US Agent’s Name: Autel Robotics USA LLC Title: PresidentTitle: Manager SignatureSignature

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Autel Robotics Co., Ltd. Grantee code: 2AGNT FCC ID: 2AGNTNEST Contact Name: Xiangxi Pan Address: 601,701,801,901, Block B1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan Dist. Shenzhen, GuangDong, 518055, China Telephone No: 86-18926791906 Fax No: 86-755-86147758 Email: [email protected] i. [Autel Robotics Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. Autel Robotics Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Autel Robotics Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 2023/08/15 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist Applicant’s Name: Autel Robotics Co., Ltd. Title: President Signature

Autel Robotics Co., Ltd. Professional installation Declaration Date: 08/15/2023 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Model Number: Nest Equipment Description: Nest FCC ID: 2AGNTNEST To Whom It May Concern, We, Autel Robotics Co., Ltd. declare that the installation and after-sales maintenance of this equipment need professional engineers to operate, and ordinary consumers can't install and repair this product. Thank you for your attention to this matter. Name: Xiangxi Pan Title: President Signature of applicant Date: 08/15/2023

C5266091_X9_Ed.2 1/1 SRD Guide Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Model Number: Nest Equipment Description: Nest FCC ID: 2AGNTNEST Gentlemen, In accordance with KDB 442812 D01 SDR Apps Guide v02r03. FCC ID: 2AGNTNEST has been examined against the following requirements. The following five questions (illustrated in figure 1) can be used for determining if a radio can elect to be, or must be an SDR: questions Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) 1. Can the RF parameters of the device be altered through software? ☒ No, not an SDR. ☐Yes, go to question 2. 2. Can third parties not permitted by the Commission through specific filings modify, configure, or load different software, or make configuration settings to operate the device or host hardware radio frequency parameters (frequency range, modulation type, maximum output power or other radio parameters) in any other way than granted (or expected to be granted)? ☒ No, go to question 3. ☐Yes, must be an SDR. 3. Is the device capable of operating in any other in any other way than granted, or will be, granted? ☒ No, go to question 5. ☐Yes, go to question 4. 4. Is this a Part 15 client device as defined in Section 15.202 (as opposed to a master device)? ☐ No, must be an SDR. ☒ Yes, qualifies as a Part 15 client device, go to question 5. 5. Does the manufacturer elect SDR? ☒ No, not an SDR. ☐Yes, elects to be an SDR. C5266091_X9_Ed.2 1/1 Name: Xiangxi Pan Date: 08/15/2013 Title: President Signature of applicant

C5266091_X8_Ed.1 1/1 Autel Robotics Co., Ltd. 601,701,801,901, Block B1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan Dist. Shenzhen, GuangDong, 518055, China Contact: Xiangxi Pan Tel: 86-18926791906 Email：[email protected] Letter of Authorization Company: Autel Robotics Co., Ltd. Address: 601,701,801,901, Block B1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan Dist. Shenzhen, GuangDong, 518055, China Product Name: Nest Model Number: Nest FCC Identifier: 2AGNTNEST We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take act ion on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Xiangxi Pan Date: 08/15/2023 Title: President Signature of applicant:

C5266091_X10_Ed.2 1/1 Autel Robotics Co., Ltd. 601,701,801,901, Block B1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan Dist. Shenzhen, GuangDong, 518055, China Contact: Xiangxi Pan Tel: 86-18926791906 Email：[email protected] Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 08/15/2023 Subject: Request for Confidentiality FCC ID: 2AGNTNEST To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☒ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☒ User’s Manual ☐ NOTE 1 ☒ Internal Photos ☐ NOTE 1 ☒ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☒ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of _180_____ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Xiangxi Pan Title: President

C5266091_X9_Ed.2 1/1 Modular Transmitter Approval Request Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Company name: Autel Robotics Co., Ltd. FCC ID: 2AGNTNEST Gentlemen, In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 ‘Module Certification Guide v01r04’. FCC ID: 2AGNTNEST has been examined against the following requirements. Items to be covered by Single modular transmitters. Requirement per 15.212 and KDB 996369 D01 ‘Modular Certification Guide v02 Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly Yes, The radio elements with shielded 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal Yes, All inputs to the modules are buffered through logic or microprocessor inputs 3. The module must contain power supply regulation on the module Yes, low drop out regulator is used for modular power supply regulation. 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) yes, Device antenna comply with the antenna requirement, and the antenna info is listed in the user manual. 5. The module must demonstrate compliance in a stand- alone configuration Yes, The module test in a stand-alone configuration 6. The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements) Yes, The modular has a permanent fixed label, and below statement was listed in the User Manual; The host device must be labelled to display the FCCID of the module Contains FCC ID: 2AGNTNEST 7. The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee Yes, The module comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee, Refer to test report and user manual 8. The module must comply with RF exposure requirements Yes, Transmitter meets MPE calculation of 47 CFR 1.1307. Refer to MPE Reports and Refer to modular installation manual C5266091_X9_Ed.2 1/1 Name: Xiangxi Pan Date: 08/15/2013 Title: President Signature of applicant

标注 模切 压线 反压线 5*5齿刀 1寸12浪波浪刀 、、、、、、、、、、、、 , '，',',＇,',' 撕裂切线 佼 粘合线 46.6 mm . ． i E E 。 c ` 刀模图 Mode l/产品暨 号：Nest FCC ID:2AGNTNEST IC: 20910-NEST 烹 C小ICES-003(8')INMB-003(B) Made In China/中国制造 ＿ 印刷图 AUTEL ROBOTICS 纸供位 图提单 深圳市道通智能航空技术股份有限公司 Autel Robotics Co., Ltd. 材质工艺要求 材 质7818昌茂0.05mm消亚银龙 成品尺寸46.6x20.3mm 成型工艺模切 尺寸偏差士0.3mm 印刷偏差士0.3mm 颜色 - 纹理方向 备注 物料名称 EVO NEST图传盒子机身贴纸 料 号 500000000 版本号 Vl 设计日期 2023/8/9 平面设计师 赵亮 结构设计师 I 核准人 ／ 历史 版本 版本号：Vl 修改 日期：2023/8/9 修改点：首发 修改人：赵亮 版本号： 修改 日期： 修改点： 修改人： 版本号： 修改 日期： 修改点： 修改人： 版本号： 修改 日期： 修改点： 修改人： 比 例 1:1 单 -－ 位 mm

Report No.: TW2306621-01E Date: 2023-07-21 Photo for the EUT -End of the report- The report refers only to the sample tested and does not apply to the bulk. Page 366 of 366 This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No.: TW2306621-04E File reference No.: 2023-07-21 Applicant: Autel Robotics Co., Ltd. 601, 701, 801, 901, Block B1, Nanshan iPark, No. 1001 Xueyuan Avenue, Nanshan District, Shenzhen, Guangdong, 518055, China Product: Nest Model No.: Nest Trademark: Autel Robotics Test Standards: FCC Part 15 Subpart B & ICES-003 Issue 7:2020 Test Result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.4&FCC Part 15&ICES-003 regulations for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: July 21, 2023 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES. Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688 Fax (755) 83442996 Email: [email protected] Report No.: TW2306621-04E Page 2 of 15 Date: 2023-07-21 "The report refers only to the sample tested and does not apply to the bulk production. This report is issued in confidential to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for illegal purpose. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES reserves the rights to withdraw it and to adopt any other remedies which may be appropriate." Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 CAB identifier: CN0033 Report No.: TW2306621-04E Page 3 of 15 Date: 2023-07-21 "The report refers only to the sample tested and does not apply to the bulk production. This report is issued in confidential to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for illegal purpose. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES reserves the rights to withdraw it and to adopt any other remedies which may be appropriate." Content 1.0 General Details ................................................................................................................................................... 4 1.1 Test Lab Details ........................................................................................................................................... 4 1.2 Applicant Details ......................................................................................................................................... 4 1.4 Submitted Sample: 1 Samples ..................................................................................................................... 4 1.5 Test Duration ............................................................................................................................................... 4 1.6 Test Uncertainty ........................................................................................................................................... 4 1.7 Test Engineer ............................................................................................................................................... 5 2.0 List of Measurement Equipment ...................................................................................................................... 6 2.1 Conducted Emission Test ............................................................................................................................. 6 2.2 Radiated electromagnetic disturbance test ................................................................................................... 6 2.3 Auxiliary Equipment .................................................................................................................................... 6 3.0 Technical Details .......................................................…

Text truncated - open the document above for the full version.

Report No.: TW2306621-01E Page 264 of 278 Date: 2023-06-21 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. 13.0 Photo of testing Radiated Emission Test Setup: Below 1GHz Above 1GHz