2AGPT-ENET2SolarEdge Energy Net

SolarEdge Home Network OK OFF AC OFF ENET-HBNP-01 ENET-HBPV3D-01 ENET-HBPJD-01 ENET-HBCL-01 1234 5 6 5MIN 1. Install the Antenna Turn off the inverter ON/OFF/P switch and DC safety switch (if applicable). SolarEdge Home Network Plug-in Installation 1 2 1 1 2 2 2. Install and Connect the Plug-in (may require communication board replacement) 4 ` 3 To avoid electric shock, refer to safety instructions in the inverter installation guide before removing the inverter cover. Turn off AC to the inverter on the main service panel. Wait five minutes. Open the inverter cover and Connection Unit cover (if applicable). Clip the antenna (supplied) to a heatsink fin. Pass the antenna cable through a communication gland. 1 Connect the SolarEdge Home Network plug-in to the dedicated socket on the communication board. 2 Connect the antenna to the SolarEdge Home Network plug-in. Tie the antenna cable to the communication board bracket with a plastic tie (supplied). Mount the inverter cover and Connection Unit cover (if applicable). Tighten the screws to 8.4 Nm/74 lbin. Replaces existing communication board SetApp 3. Verify Connection 3 Run SetApp 4 Scan the QR code on the inverter. 5 Verify connection. Commissioning Status Communication ON 21 Turn on the inverter ON/OFF/P switch and DC safety switch (if applicable). Turn on AC to the inverter on the main service panel. ON AC The installation of the SolarEdge Home Network Plug-in must be performed by a qualified installer only. Make sure to follow all safety and handling instructions specified in the inverter installation guide. Version 1.3, October 2022 Datasheet To view the SolarEdge Home Network technical specifications, scan the QR code: Or follow the link: https://www.solaredge.com/sites/default/files /se-energy-net-plug-in-datasheet.pdf Plug-in occupies cellular socket Plug-in Selection Guide To view the SolarEdge Home Network Plug-in Selection technical note, scan the QR code: Or follow the link: https:// www.solaredge.com/sites/default/files /se-energynet-plugin-kit-selection-tech- note.pdf SolarEdge Energy Net Installation The installation of the SolarEdge Energy Net must be performed by a qualified installer only. RRegulatory Statements Professional Installation Instructions Installation Personnel This product is designed for a specific application, and needs to be installed by qualified personnel. The user should not attempt to install the product or change any of the product settings. External Antenna Use only the antennas, which have been approved by the applicant. Unapproved antenna(s) may produce unwanted spurious or excessive RF transmitting power, which may lead to violation of FCC/IC limits and is prohibited. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pr otection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communicat ions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate th is equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:  This module has been tested for compliance to FCC Part 15.  The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. RF Exposure Considerations This equipment complies with the FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. Approved antenna(s) list: Manufacturer Model Antenna Type Max Gain (dBi) Impedance (Ω)) RALTRON RST-TUA3-TUB7-320020-17M-A-002 Dipole 3dBi 50ohm RALTRON RST-TUA3-TUB7-19550200-17M…

Text truncated - open the document above for the full version.

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD21046 Dear Sir/Madam, Our product SolarEdge Energy Net, model: ENET2, FCC ID: 2AGPT-ENET2, for marketing purpose, only supports Lora( 906-924MHz). The other functions, bands and modes has been shielded by the manufacturer using the software, the end user has no capability to activate it. Signature:

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] CFR 47 §2.911(d)(5)(i) Attestation Letter Attestation Letter Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: 2AGPT-ENET2 SolarEdge Technologies Ltd certifies that the equipment for which authorization is sought, is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] CFR 47 §2.911 (d)(5)(ii) Attestation Letter Attestation Letter Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: 2AGPT-ENET2 SolarEdge Technologies Ltd certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature

U.S. AGENT LETTER OF ATTESTATION Date: 2024-04-28 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2AGPT-ENET2 SolarEdge Technologies Ltd certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. SolarEdge Technologies Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: SolarEdge Technologies Ltd Address: 1 HaMada Street, Herzeliya 467335 Israel. FRN: 0025091117 Tel: +97299576620 Extension: 4003 Email: [email protected] Signed by (printed name): Rami Nataf Signature:

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] QA-FR-170-B 7/29/2014 FCC Authorization Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, SolarEdge Technologies Ltd, the undersigned, hereby authorizes Bay Area Compliance Laboratories Corp. (Shenzhen) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. (Shenzhen) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature:

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] FCC Confidential Authorization Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AGPT-ENET2 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, SolarEdge Technologies Ltdhereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] Product Similarity Declaration Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD21046 Dear Sir/Madam, We, SolarEdge Technologies Ltd, hereby declare that we have a product named as SolarEdge Energy Net, model: ENET2 (FCC ID: 2AGPT-ENET2) was tested by Bay Area Compliance Laboratories Corp. (Shenzhen). The device has different connector and antenna, other is the same. Connector Antenna With UFL Connector ANT AS4035-1 With RA SMA Top ANT AS4035-1 ANT AS4038-1 SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] ANT AS4034-1 With RA SMA Bottom ANT AS4035-1 ANT AS4038-1 ANT AS4034-1 With SMA Connector (Vertical top) ANT AS4035-1 ANT AS4038-1 ANT AS4034-1 SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] With SMA Connector (Vertical bottom) ANT AS4035-1 ANT AS4038-1 ANT AS4034-1 We confirm that all information above is true, and we’ll be responsible for all the consequences. Please contact me if you have any question. Sincerely Yours, Signature: Rami Nataf EMC & Radio Certification Manager

SolarEdge Technologies Ltd 1 HaMada Street, Herzeliya 467335 Israel. Tel: +97299576620 Extension: 4003 Fax: +97299576591 Email: [email protected] Modular Approval Letter Date: 2024-06-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Application Examiner, We, SolarEdge Technologies Ltd is submitting this application for certification of product named as SolarEdge Energy Net, Model Numbers: ENET2 (FCC ID: 2AGPT-ENET2). It is seeking modular approval. The radio meets the requirements for modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below: 1. “The modular transmitter must have its own RF shielding.” Yes, it is fulfilled. The radio portion of the module has its own RF shielding. The shielding is installed at the factory. Please see the EUT photos. 2. “The modular transmitter must have buffered modulation/data inputs.” Yes, it is fulfilled. The EUT has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over modulation. Please see the Schematics exhibit. 3. “The modular transmitter must have its own power supply regulation.” Yes, it is fulfilled. The EUT has its own power supply regulation to insure compliance. 4. “The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c).” Yes. The EUT has three types of antennas: PCB, dipole, monopole antenna. 5. “The modular transmitter must be tested in a stand-alone configuration.” Yes, it is fulfilled. The EUT was tested in a stand-alone configuration. 6. “The modular transmitter must be labeled with its own FCC ID number.” Yes, it is fulfilled. The module will be labeled with its own FCC ID number. Please see FCC ID label & location exhibit. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” Yes, it is fulfilled. The necessary explanation to be complied with this requirement is contained in the user manual, and please refer to the User manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” Yes, the module is intended to use in distance more that 20cm. FCC RF exposure requirement satisfied with 47CFR §2.1091. Please contact me if you have additional questions. Your attention to this matter is greatly appreciated. Signature: Rami Nataf EMC & Radio Certification Manager

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 1 of 13 EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS With UFL Connector: Test Jig EUT Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 2 of 13 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 3 of 13 ANT AS4035-1 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 4 of 13 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 5 of 13 With RA SMA Top: Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 6 of 13 With RA SMA Bottom: Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 7 of 13 With SMA Connector (Vertical top): Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 8 of 13 With SMA Connector (Vertical bottom): Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 9 of 13 ANT AS4034-1 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 10 of 13 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 11 of 13 ANT AS4035-1 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 12 of 13 Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 13 of 13 ANT AS4038-1

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF EXHIBIT A - FCC ID LABEL AND LOCATION With UFL Connector: FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF With RA SMA Top: FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF With RA SMA Bottom: FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF With SMA Connector (Vertical top): FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF With SMA Connector (Vertical bottom): FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 1 of 5 EXHIBIT C - EUT INTERNAL PHOTOGRAPHS With UFL Connector: Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 2 of 5 With RA SMA Top: Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 3 of 5 With RA SMA Bottom: Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 4 of 5 With SMA Connector (Vertical top): Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1240126-06326E-RF Page 5 of 5 With SMA Connector (Vertical bottom):

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: SZ1240126-06326E-RF TR-EM-RF088 Page 12 of 53 Version 1.0 (2023/10/07) FCC §15.247 (i) & §1.1307 (B) (3) & §2.1091- RF EXPOSURE Applicable Standard According to KDB 447498 D04 Interim General RF Exposure Guidance MPE-Based Exemption: An alternative to the SAR-based exemption is provided in § 1.1307(b)(3)(i)(C), for a much wider frequency range, from 300 kHz to 100 GHz, applicable for separation distances greater or equal to λ/2π, where λ is the free-space operating wavelength in meters. The MPE-based test exemption condition is in terms of ERP, defined as the product of the maximum antenna gain and the delivered maximum time-averaged power. For this case, a RF source is an RF exempt device if its ERP (watts) is no more than a frequency-dependent value, as detailed tabular form in Appendix B. These limits have been derived based on the basic specifications on Maximum Permissible Exposure (MPE) considered for the FCC rules in § 1.1310(e)(1). f = frequency in MHz; R = minimum separation distance from the body of a nearby person (appropriate units, e.g., m); Result For worst case: Mode Frequency (MHz) Tune up conducted power # Antenna Gain # ERP Evaluation Distance (m) ERP Limit (mW) (dBm) (dBi)(dBd)(dBm)(mW) OQPSK 906-924 19.5 2 -0.15 19.35 86.10 0.2 464 Note 1: The tune-up power and antenna gain was declared by the applicant. Note 2: 0dBd=2.15dBi. To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm from nearby persons. Result: Compliant

SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Rev Editor Date change 01 Uri.Itzack 21/01/0120 Initial Document 02 Uri Itzack 16/01/2023 Add SWR measurement Manufacturer: SolarEdge SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Specification Electrical Frequency Range 960-700 /2700-1700 HzM V.S.W.R ≤4.0 Antenna Type monopole Radiation Omni Directional Gain (Max) 0 dBi Polarization Vertical Max Input Power 5 W width -Vertical Beam 30 width -Horizontal Beam 360 Deg Impedance 50 Ohm Antenna design monople Internal Material PCB Cable RG316 Mechanical Length 200 mm Diameter 20 mm Cable length (Max) 135 cm Connector RP SMA Antenna Weight 50 gr Application Outdoor\Indoor IP Rating Base Material PC Lexan 503R-WH5151L or WH8G952 Sabic Storage temperature -40 to +85 Operating Temperature -40 to +85 Storage Humidity 10% ~90% condensing-non SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com ation PatternsRad Horizontal Pattern Vertical Pattern SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Standing Wave Ratio - SWR Graph

Page 1 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Rev Editor Date change 1.0 Uri.Itzack 21/08/2022 Initial Document 0.2 Amit.Ovadia 2022/10/31 New matching network 0.3 Uri.Itzack 26/06/2024 Update parameters Update footer Model number: AS4035-1 Manufacturer: SolarEdge g SE PN: AP1756B-AN-03 860-930MHz Coil Antenna na –– Internal Antennanna 860-930MHz PCB Antenna Page 2 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com ͵ͲǦǦ͹ͷ͸ͳȂ’‡…‹ˆ‹…ƒ–‹‘ Electrical Frequency Rang 860 – 930 MHz V.S.W.R >3 Antenna Type oilC Radiation Omni Directional Gain (Max) 0dBi Polarization Vertical Max Input Power 3W width -Vertical Beam 60 o width -Horizontal Beam 360 o Impedance 50 Ohm Antenna design monopole Internal Material Copper Connector U.FL (I.PEX connector) Mechanical [mm]Length 41 Width [mm] 11.5 Antenna Weight ~20g Application Indoor Storage temperature -40 to +80C Operating Temperature -40 to +70C Storage Humidity 5%~90% Condensing-Non Operating Humidity 10% ~90% Condensing-Non Frequency Range 860 - 930 V.S.W.R >3 Antenna Type oilC PCB PCB Page 3 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com ‡…Šƒ‹…ƒŽ”ƒ™‹‰ …Š‡ƒ–‹…  Page 4 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com ƒ†‹ƒ–‹‘ƒ––‡”  ʹ…—–•  Page 5 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com   Page 6 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com ƒ‹˜•Ǥ ”‡“—‡…›‰”ƒ’Š

Page 1 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Rev Editor Date change 1.0 Uri.Itzack 13/12/2023 Initial Document 0.2 Uri.Itzack 13/12/2023 Update graphs 0.3 Uri.Itzack 26/06/2024 Updated footer Model number: AS4038-1 Manufacturer: SolarEdge SE PN: D2143AC 860-930MHz Dipole Antenna – External Antenna Page 2 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com A – SpecificationS4038-1 Electrical Frequency Rang e 860~930MHz V.S.W.R <2 Antenna Type Dipole Radiation Omni Directional Gain (Max) 2dBi Polarization Vertical Max Input Power 3W width -Vertical Beam 60 o width -Horizontal Beam 360 o Impedance 50 Ohm Antenna Type Dipole Internal Material PCB Cable RG316 Connector RP SMA Mechanical [mm]Length 200 Width [mm] 20 Antenna Weight ~50gr Cable length (Max) 180cm Application Indoor\Outdoor temperatureStorage -40C ~ 105C Operating Temperature -40C ~ 105C Storage Humidity 5%~90% Condensing-Non Operating Humidity 10% ~90% Condensing-Non Base Material PC Lexan 503R-WH5151L or WH8G952 Sabic IP Rating IP67 Antenna Type Dipole Page 3 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Mechanical Drawing PCB Mechanical Drawing Page 4 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com Radiation Pattern 2D cuts XY Page 5 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com XZ Gain vs. Frequency graph Page 6 of 6 SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya, 4673335, Israel. +927.9.6576620 solaredge.com VSWR

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF088 Page 1 of 53 Version 1.0 (2023/10/07) TEST REPORT Applicant Name : SolarEdge Technologies Ltd Address : 1 HaMada Street, Herzeliya 467335 Israel Report Number : SZ1240126-06326E-RF FCC ID: 2AGPT-ENET2 IC: 20916-ENET2 Test Standard (s) FCC PART 15.247; RSS-GEN ISSUE 5, FEBRUARY 2021 AMENDMENT 2; RSS-247 ISSUE 3, AUGUST 2023 Sample Description Product Type: SolarEdge Energy Net Model No.: ENET2 Multiple Model(s) No.: N/A Trade Mark: solaredge Date Received: 2024/01/26 Issue Date: 2024/07/10 Test Result: Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: April Zhang Nancy Wang RF Engineer RF Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: SZ1240126-06326E-RF TR-EM-RF088 Page 2 of 53 Version 1.0 (2023/10/07) TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 GENERAL INFORMATION ....................................................................................................................................... 5 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 5 OBJECTIVE ................................................................................................................................................................... 5 TEST METHODOLOGY .................................................................................................................................................. 5 MEASUREMENT UNCERTAINTY .................................................................................................................................... 6 SYSTEM TEST CONFIGURATION .......................................................................................................................... 7 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 7 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 7 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 DUTY CYCLE ................................................................................................................................................................ 8 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 8 EXTERNAL I/O CABLE .................................................................................................................................................. 8 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 9 SUMMARY OF TEST RESULTS ............................................................................................................................. 10 TEST EQUIPMENT LIST ......................................................................................................................................... 11 FCC §15.247 (I) & §1.1307 (B) (3) & §2.1091- RF EXPOSURE ............................................................................. 12 RSS-102 § 2.5.2 –EXEMPTION LIMITS FOR ROUTINE EVALUATION-RF EXPOSURE EVALUATION 13 APPLICABLE STANDARD ...................…

Text truncated - open the document above for the full version.