2AGQ6-MINIINmPOS

封面 封底 成品尺寸：100x63mm | 成品材质：128g 铜版纸 | 出血：3mm | 成品折法：风琴折 | 注意：线框不要印出 63mm 100mm Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 0cm from all persons. after evaluation, because the power is low, it can be exempted from the SAR test and meet the requirements of the FCC.

Technology (Beijing) Inrc.l lRm. ,812C, #1O(Universal B;usiness Park), Jiuxianqiao Road, Chaoyang District, Beijing, [July 12, 20231 al Communications Comrnission and Evaluation Division : [2AGQ6-M!NllN] US Agent - Atte,station lStatement / Part 2.911(dX7) Technology (Beijing) lrrc.l certifies, that as of [July 12,20231, we have designated FCC , LLC to accept service of process on our behalf for FCC lD: [2AGQ6-MlNllN]. Technology (Beijing) Inc.l, accepts to maintain an agent of service of process in the States for no less than onre year after elither the grantee has permanently terminated all ing and importation of the applicable e<luipment within the U.S., or the conclusion of any administrati,ue or judicial proceeding involving the equipment, whichever is Agent, LLC, accepts as of the date of the filing of this application, the obligation of being agent for the purpose of accepting service of process on behalf of [[Dspread (Beijing) Inc.lfor FCC lD: [2AGQ6-M|NllN]. nated Agent Information: Name: FCC US Agent, LLC '.3722lllinois Avenue, Saint Charles, lL, 60174, USA Person:Tim Payne >:708-571-3148 : [email protected];om y: [Dspread Technology (BeUing) lnc.]Designated Agent: FCC US Agent, LLC Designated Agent Representative: Tim Payne Signature: Representative: [echo wang] (/h" **f

Dspread Technology (Beijingl Inc. Electrical and Electronic Testing NA, Inc. West Patapsco Avenue : Attestation Statements F,art 2.911(dXs)(ii) request for 2AGQ5-MlNllN Technology (Beijinrg| Inc.l ("the applicant") certifies that, as of the date of the of the application, the applicant is not identified on the Covered List as an entity ucing "covered" equipnrent. icant signature) -/.''[P icant printed name) Dspread Technology (Beijing) Inc. rofins Electrical and Electronic Testing NA, Inc. West Patapsco Avenue Itimore, MD 21230 : Attestation Statements Part 2.911(dX5)(i) request for 2AGQ6-MlNllN Technology (Beijirng) Inc.l ("the applicant") certifies that the equipment for nt authorization pursuant to section 2.903 of the FCC rules. licant signature) 6'l'* **"1 licant printed name)

Dspread Technology (Beijing) Inc. rofins Electrical and Electronic Testing NA, Inc. West Patapsco Avenue the undersigned, her,eby authorize TA Technology (Shanghai) Co., Ltd. /zhao junlin act on our behalf in all matters relating to application for equipment authorization, luding the signing of aLll documents relating to these matters. also hereby certify that no party to the application authorized hereunder is subject to denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug is agreement expires one year from the current date. in print): Echo Wang y: Dspread Technology (Beijing) Inc. ict, Beijing, China

Datr:: Subject: Pun;uantFCC 47 CRF 0.457(d) and 0.,459 and IC RSP-100, Section 10, the applicant requests that a part of the sub.jectapplication be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term X Pemranent Exhibit Block Diagrams Extemal Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement Schematics Test Setup Photos User's Manual Permanent*l Pemlanent Perrnanent Perrnanent Pernnanent* Technology (Beijing) Inc.__has spent substantial effort in developing this product and it is one of the its kind in industry. Having the subject information easily available to "competition" would negate the they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permat Confidentiality: Therappli requests the exhibits listed above as permanently confidential be permanently withheld from public to materials that contain trade secrets and proprietary information not customarily released to the public. Confidentiality: The appl requests the exhibits selected above as short term confidential be withheld from public view for a period ,of 0_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to Lature release of sensitive infonmation prior to marketing or release of the product to the public. Applicant is also that they are responsible to notify TCB in the event information regarding the product or the product is lable to the public. TCB will then release the documents listed above for public disclosure pursuant to Industry Canada Applications: The appli understands that until suchL time that lC distinguishes between Short Term and Permanent Con lity, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely

EUT Appearance Report No.: R2306A0679 TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 1 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance EUT Appearance Report No.: R2306A0679 TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 2 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: R2306A0679 TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 3 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. a: EUT EUT Appearance Report No.: R2306A0679 TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 4 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. b: USB Cable Picture 1: Constituents of EUT

InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage1of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. Internalphoto InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage2of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage3of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage4of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage5of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage6of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. InternalphotoFCCID:2AGQ6-MINIIN TATechnology(Shanghai)Co.,Ltd.TA-MB-01-033EPage7of7 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd.

Prepared by: Wei Fangying Approved by: Fan Guangchang TA Technology (Shanghai) Co., Ltd. Building 3, No.145, Jintang Rd, Pudong Shanghai, P.R.China TEL: +86-021-50791141/2/3 FAX: +86-021-50791141/2/3-8000 SAR Exemption Evaluation Applicant Dspread Technology (Beijing) Inc. FCC ID 2AGQ6-MINIIN Product mPOS Brand Dspread Model QPOS mini Report No. R2306A0680-S1 Issue Date July 10, 2023 SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 2 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Table of Contents 1 Test Laboratory ............................................................................................................................... 3 1.1 Notes of the Test Report ......................................................................................................... 3 1.2 Test Facility ............................................................................................................................. 3 1.3 Testing Location ...................................................................................................................... 3 1.4 Laboratory Environment .......................................................................................................... 3 2 Description of Equipment Under Test ............................................................................................. 4 3 Test Specification, Methods and Procedures ................................................................................. 6 4 Output Power ................................................................................................................................. 7 5 Standalone SAR Test Exclusion Considerations .......................................................................... 10 ANNEX A: The EUT Appearance .......................................................................................................... 11 SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 3 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1 Test Laboratory 1.1 Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA Technology (Shanghai) Co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2 Test Facility FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform measurements. 1.3 Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: Building 3, No.145, Jintang Rd, Pudong Shanghai, P.R.China City: Shanghai Post code: 201201 Country: P. R. China Contact: Fan Guangchang Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: [email protected] 1.4 Laboratory Environment Temperature Min. = 18C, Max. = 25 C Relative humidity Min. = 30%, Max. = 70% Ground system resistance < 0.5  Ambient noise is checked and found very low and in compliance with requirement of standards. Reflection of surrounding objects is minimized and in compliance with requirement of standards. SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 4 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 2 Description of Equipment Under Test Client Information Applicant Dspread Technology (Beijing) Inc. Applicant address Rm.407, B12C, #10(Universal Business Park), Jiuxianqiao Road, Chaoyang District, Beijing, China Manufacturer Dspread Technology (Beijing) Inc. Manufacturer address Rm.407, B12C, #10(Universal Business Park), Jiuxianqiao Road, Chaoyang District, Beijing, China General Technologies EUT Stage Identical Prototype Model QPOS mini SN 0276001202303230027 Hardware Version 2.3.1 Software Version 1.3.6 Antenna Type Internal Antenna Date of Testing June 19, 2023 ~ June 21, 2023 Date of Sample Received June 13, 2023 Note: The EUT is sent from the applicant to TA and the information of the EUT is declared by the applicant. SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 5 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Wireless Technology and Frequency Range Wireless Technology Modulation Operating Mode Tx (MHz) Bluetooth 2.4G Version 4.1 BR + LE 2402 ~2480 NFC 13.56MHz SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 6 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 3 Test Specification, Methods and Procedures Reference Standards KDB 447498 D01 General RF Exposure Guidance v06 SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 7 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 4 Output Power Bluetooth Conducted Power(dBm) Channel/Frequency(MHz) Ch 0/2402 MHz Ch 39/2441 MHz Ch 78/2480 MHz GFSK -4.22 -4.64 -4.39 Bluetooth LE Ch 0/2402 MHz Ch 19/2440 MHz Ch 39/2480 MHz GFSK(1M) -5.92 -6.02 -5.74 SAR exemption evaluation Report No.: R2306A0680-S1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-008S Page 8 of 11 This report shall not be reproduced except in full, wi…

Text truncated - open the document above for the full version.

鼎合远传技术 （北京）股份有限公司 第1页·共5页 文件编号 发行版次 V1.0 主责部门 研发一部 发行日期 2022-07-13 BT天线测试报告 BT Antenna Test Report 编 制: 晏海涛 Codification：Yan Haitao 日期:2023年7月13日 Date：2 023 -07-13 鼎合远传技术 （北京）股份有限公司 第2页·共5页 修改记录 版本号 作者 修改说明 日期 1.0 晏海涛 1. 编写BT天线测试报告 1. Preparation of BT antenna test reports 2023-07-13 鼎合远传技术 （北京）股份有限公司 第3页·共5页 1. 测试简述 Brief description of the test 鼎合远传针对A27in产品的BT天线开展测试工作，本测试包含了频段、性能、无源效率、增益、2D和 3D增益进行了全方面的测试工作。 Dspread's BT antenna for the A27in product was tested for band, performance, passive efficiency, gain, 2D and 3D gain. 2. BT天线展示 BT antenna display 3. 测试结论 Test conclusions 3.1 频段 Frequency Band TX：2400MHz~2480MHz RX：2400MHz~2480MHz 3.2 S11 天线性能如下，工作频段覆盖整个ISM 2.4G频段 S11 antenna performance is as follows，the operating band covering the entire ISM 2.4G band ； 鼎合远传技术 （北京）股份有限公司 第4页·共5页 3.3 天线的无源效率和增益 The antenna passive efficiency and gain Fre(MHz) Eff(dB) Gain(dB) 2400 -11.8 -4.09 2410 -11.74 -4 2420 -11.62 -4.12 2430 -11.68 -4.05 2440 -11.19 -4.06 2450 -11.14 -4.03 2460 -10.81 -4.08 2470 -10.81 -3.96 2480 -10.08 -3.91 2490 -10.02 -3.89 2500 -9.64 -3.9 3.4 2D和3D的增益如下 The gain of 2D and 3D is as follows 鼎合远传技术 （北京）股份有限公司 第5页·共5页

Prepared by: Xu Ying Approved by: Xu Kai TA Technology (Shanghai) Co., Ltd. Building 3, No.145, Jintang Rd, Pudong Shanghai, P.R.China TEL: +86-021-50791141/2/3 FAX: +86-021-50791141/2/3-8000 RF TEST REPORT Applicant Dspread Technology (Beijing) Inc. FCC ID 2AGQ6-MINIIN Product mPOS Model QPOS mini Report No. R2306A0680-R1 Issue Date July 6, 2023 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 15C (2022). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. RF Test Report Report No.: R2306A0680-R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-004R Page 2 of 55 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. TABLE OF CONTENT 1 Test Laboratory ............................................................................................................................ 4 1.1 Notes of the Test Report ......................................................................................................... 4 1.2. Test facility ............................................................................................................................ 4 1.3 Testing Location ...................................................................................................................... 4 2 General Description of Equipment under Test .......................................................................... 5 2.1 Applicant and Manufacturer Information.................................................................................. 5 2.2 General information ................................................................................................................. 5 3 Applied Standards ........................................................................................................................ 6 4 Information about the FHSS characteristics .............................................................................. 7 4.1 Frequency Hopping System Requirement............................................................................... 7 4.2 Pseudorandom Frequency Hopping Sequence ....................................................................... 8 4.3 Equal Hopping Frequency Use ............................................................................................... 9 4.4 System Receiver Input Bandwidth .......................................................................................... 9 4.5 Test Configuration ................................................................................................................. 10 5 Test Case Results ........................................................................................................................ 11 5.1 Peak Power Output ................................................................................................................ 11 5.2 Occupied Bandwidth (20dB) .................................................................................................. 14 5.3 Frequency Separation ........................................................................................................... 17 5.4 Time of Occupancy (Dwell Time) ........................................................................................... 20 5.5 Band Edge Compliance ........................................................................................................ 25 5.6 Number of hopping Frequency .............................................................................................. 30 5.7 Spurious RF Conducted Emissions ....................................................................................... 32 5.8 Unwanted Emission .............................................................................................................. 37 5.9 Conducted Emission ............................................................................................................. 50 6 Main Test Instruments ................................................................................................................ 53 ANNEX A: The EUT Appearance ...................................................................................................... 54 ANNEX B: Test Setup Photos ........................................................................................................... 55 RF Test Report Report No.: R2306A0680-R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-004R Page 3 of 55 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Summary of Measurement Results Number Test Case Clause in FCC rules Verdict 1 Frequency Hopping System 15.247 (g), (h) PASS 2 Peak Power Output 15.247(b)(1) PASS 3 99% Bandwidth and 20dB Bandwidth 15.247(a)(1) C63.10 6.9 PASS 4 Frequency Separation 15.247(a)(1) PASS 5 Time of Occupancy (Dwell Time) 15.247(a)(1)(iii) PASS 6 Band Edge Compliance 15.247(d) PASS 7 Number of Hopping Frequency 15.247(a)(1)(iii) PASS 8 Spurious RF Conducted Emissions 15.247(d) PASS 9 Unwanted Emissions 15.247(d),15.205,15.209 PASS 10 Conducted Emissions 15.207 PASS Date of Testing: June 16, 2023 ~ July 3, 2023 Date of Sample Received: June 13, 2023 Note: PASS: The EUT complies with the essential requirements in the standard. FAIL: The EUT does not comply with the essential requirements in the standard. All indications of Pass/Fail in this report are opinions expressed by TA Technology (Shanghai) Co., Ltd. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. RF Test Report Report No.: R2306A0680-R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-004R Page 4 of 55 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1 Test Laboratory…

Text truncated - open the document above for the full version.

RF Test Setup Report No: R2306A0680 TA Technology (Shanghai) Co., Ltd. TA-MB-01-107R Page 1 of 3 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Part15C Test Setup RF Test Setup Report No: R2306A0680 TA Technology (Shanghai) Co., Ltd. TA-MB-01-107R Page 2 of 3 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Picture 1 Radiated Emission Test Setup RF Test Setup Report No: R2306A0680 TA Technology (Shanghai) Co., Ltd. TA-MB-01-107R Page 3 of 3 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Picture 2 Conducted Emission Test Setup