2AH2P-BC90019GPS BIKE COMPUTER

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. Canada, Industry Canada (IC) Notices This device complies with Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. (antennas are less than 20 cm of a person's body). Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils portables. (les antennes sont moins de 20 cm du corps d'une personne).

Report No.: 1908TW8501-U2~U4 Product: GPS BIKE COMPUTER Brand Name: DECATHLON Model Number: BC900 1 of 4 External Photograph (1) EUT Photo (2) EUT Photo Report No.: 1908TW8501-U2~U4 2 of 4 (3) EUT Photo (4) EUT Photo Report No.: 1908TW8501-U2~U4 3 of 4 (5) EUT Photo (6) EUT Photo Report No.: 1908TW8501-U2~U4 4 of 4 (7) EUT Photo (8) EUT Photo

Label Label location

Report No.: 1908TW8501-U2~U4 Product: GPS BIKE COMPUTER Brand Name: DECATHLON Model Number: BC900 1 of 6 Internal Photograph (1) EUT Photo (2) EUT Photo Report No.: 1908TW8501-U2~U4 2 of 6 (3) EUT Photo (4) EUT Photo Report No.: 1908TW8501-U2~U4 3 of 6 (5) EUT Photo (6) EUT Photo Report No.: 1908TW8501-U2~U4 4 of 6 (7) EUT Photo (8) EUT Photo Report No.: 1908TW8501-U2~U4 5 of 6 (9) EUT Photo (10) EUT Photo Report No.: 1908TW8501-U2~U4 6 of 6 (11) EUT Photo (12) EUT Photo

MRT Technology (Taiwan) Co., Ltd Report No.: 1908TW8501-U4 Phone: +886-3-3288388 Report Version: 1.0 Fax: +886-3-3288918 Issue Date: 2019-09-19 Web: www.mrt-cert.com FCC ID: 2AH2P-BC90019 Page Number: 1 of 7 RF Exposure Evaluation FCC ID: 2AH2P-BC90019 APPLICANT: DECATHLON USA LLC Application Type: Certification Product: GPS BIKE COMPUTER Model No.: BC900 Trademark: FCC Rule Part(s): Part 2.1091 (Mobile) Test Procedure(s): KDB 447498 D01v06 Received Date: August 2, 2019 Test Date: August 28 ~ September 5, 2019 Tested By : ( Peter Syu ) Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker) The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. Report No.: 1908TW8501-U4 FCC ID: 2AH2P-BC90019 Page Number: 2 of 7 Revision History Report No. Version Description Issue Date Note 1908TW8501-U4 1.0 Original Report 2019-09-19 Report No.: 1908TW8501-U4 FCC ID: 2AH2P-BC90019 Page Number: 3 of 7 1. PRODUCT INFORMATION 1.1. Equipment Description 1.2. Antenna Description No. Manufacturer Part No. Antenna Type Peak Gain 1 Advanced Ceramic X AT3216-B2R7HAA Chip 0.5dBi Product Name GPS BIKE COMPUTER Model No. BC900 Trademark Supports Radios Spec. BLE 4.2 ANT+ GPS Bluetooth Specification V4.2 LE Operating Frequency 2402~2480MHz Type of modulation GFSK Battery DC 3.7V / 1.3Wh / 350mAh Item code 2538963 Conception code 124542 Model code 8487158 Report No.: 1908TW8501-U4 FCC ID: 2AH2P-BC90019 Page Number: 4 of 7 2. RF Exposure Evaluation 2.1. FCC Limits According to FCC KDB 447498 Section 4.3 - General SAR test exclusion guidance For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where 1. f(GHz) is the RF channel transmit frequency in GHz 2. Power and distance are rounded to the nearest mW and mm before calculation 3. The result is rounded to one decimal place for comparison 4.The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm, and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 4.1 f) is applied to determine SAR test exclusion. 2.2. IC Limits Output power level shall be the higher of the maximum conducted or equivalent isotropically radiated power (e.i.r.p.) source-based, time-averaged output power. For controlled use devices where the 8 W/kg for 1 gram of tissue applies, the exemption limits for routine evaluation in Table 1 are multiplied by a factor of 5. For limb-worn devices where the 10 gram value applies, the exemption limits for routine evaluation in Table 1 are multiplied by a factor of 2.5. If the operating frequency of the device is between two frequencies located in Table 1, linear interpolation shall be applied for the applicable separation distance. For test separation distance less than 5 mm, the exemption limits for a separation distance of 5 mm can be applied to determine if a routine evaluation is required. Report No.: 1908TW8501-U4 FCC ID: 2AH2P-BC90019 Page Number: 5 of 7 Frequency (MHz) Exemption Limits (mW) At separation distance of ≤5 mm At separation distance of 10 mm At separation distance of 15 mm At separation distance of 20 mm At separation distance of 25 mm 300 71 mW 101 mW 132 mW 162 mW 193 mW 450 52 mW 70 mW 88 mW 106 mW 123 mW 835 17 mW 30 mW 42 mW 55 mW 67 mW 1900 7 mW 10 mW 18 mW 34 mW 60 mW 2450 4 mW 7 mW 15 mW 30 mW 52 mW 3500 2 mW 6 mW 16 mW 32 mW 55 mW 5800 1 mW 6 mW 15 mW 27 mW 41 mW Frequency (MHz) At separation distance of 30 mm At separation distance of 35 mm At separation distance of 40 mm At separation distance of 45 mm At separation distance of ≥50 mm ≤300 223 mW 254 mW 284 mW 315 mW 345 mW 450 141 mW 159 mW 177 mW 195 mW 213 mW 835 80 mW 92 mW 105 mW 117 mW 130 mW 1900 99 mW 153 mW 225 mW 316 mW 431 mW 2450 83 mW 123 mW 173 mW 235 mW 309 mW 3500 86 mW 124 mW 170 mW 225 mW 290 mW 5800 56 mW 71 mW 85 mW 97 mW 106 mW Table 1: SAR evaluation – Exemption limits for routine evaluation based on frequency and separation distance. Report No.: 1908TW8501-U4 FCC ID: 2AH2P-BC90019 Page Number: 6 of 7 2.3. Simultaneous transmission SAR test exclusion considerations When an antenna qualifies for the standalone SAR test exclusion of 4.3.1 and also transmits simultaneously with other antennas, the standalone SAR value must be estimated according to the following to determine the simultaneous transmission SAR test exclusion criteria: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg, for test separation distances ≤ 50 mm; where x = 7.5 for 1-g SAR and x = 18.75 for 10-g extremity SAR. When the sum of 1-g or 10-g extremity SAR of all simultaneously transmitting antennas in an operating mode and exposure condition combination is within the SAR limit, SAR test exclusion applies to that simultaneous transmission configuration. Report No.: 1908TW8501-U4 FCC ID: 2AH2P-BC90019 Page Number: 7 of 7 2.4. Test Result of RF Exposure Evaluation Standalone : Mode Frequency Band (MHz) Output Power (dBm) Output Power (mW) FCC SAR Test Exclusion Threshold (mW) Antenna Gain (dBi) EIRP (mW) IC SAR Test Exclusion Threshold (mW) BLE 2402~2480 -2.5 0.56 10 0.5 0.63 4 ANT+ 2402~2480 -2.5 0.56 10 0.5 0.63 4 Simultaneous : Mode Frequency Band (MHz) Output Power (dBm) Output Power (mW) SAR test exclusion criteria (W/Kg) BLE 2402~2480 -2.5 0.56 0.02 ANT+ 2402~2480 -2.5 0.56 0.02 BLE: 0.02W/K…

Text truncated - open the document above for the full version.

MRT Technology (Taiwan) Co., Ltd Report No.: 1908TW8501-U3 Phone: +886-3-3288388 Report Version: 1.0 Fax: +886-3-3288918 Issue Date: 2019-09-19 Web: www.mrt-cert.com FCC ID: 2AH2P-BC90019 Page Number: 1 of 50 FCC ID: 2AH2P-BC90019 APPLICANT: DECATHLON USA LLC Application Type: Certification Product: GPS BIKE COMPUTER Model No.: BC900 FCC Classification: (DTS) Digital Transmission System FCC Rule Part(s): Part 15.247 Test Procedure(s): ANSI C63.10-2013, KDB 558074 D01v05r02 Received Date: August 2, 2019 Test Date: August 14 ~ 28, 2019 MEASUREMENT REPORT FCC PART 15.247 & RSS-247 ANT+ The test results only relate to the tested sample. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 558074. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. Tested By : ( Peter Syu ) Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker) Report No.: 1908TW8501-U3 FCC ID: 2AH2P-BC90019 Page Number: 2 of 50 Revision History Report No. Version Description Issue Date Note 1908TW8501-U3 1.0 Original Report 2019-09-19 Report No.: 1908TW8501-U3 FCC ID: 2AH2P-BC90019 Page Number: 3 of 50 CONTENTS Description Page §2.1033 General Information ......................................................................................................... 5 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope .................................................................................................................................... 6 1.2. MRT Test Location ................................................................................................................ 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description .......................................................................................................... 7 2.2. Product Specification Subjective to this Standard .................................................................. 7 2.3. Test Mode ............................................................................................................................. 7 2.4. Operation Frequency / Channel List ...................................................................................... 8 2.5. Test Configuration ................................................................................................................. 9 2.6. Test Software ........................................................................................................................ 9 2.7. EMI Suppression Device(s)/Modifications ............................................................................. 9 2.8. Labeling Requirements ......................................................................................................... 9 3. DESCRIPTION of TEST ........................................................................................................ 10 3.1. Evaluation Procedure .......................................................................................................... 10 3.2. AC Line Conducted Emissions ............................................................................................ 10 3.3. Radiated Emissions ............................................................................................................ 11 4. ANTENNA REQUIREMENTS ................................................................................................ 12 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 13 6. MEASUREMENT UNCERTAINTY ......................................................................................... 14 7. TEST RESULT ...................................................................................................................... 15 7.1. Summary ............................................................................................................................. 15 7.2. Occupied Bandwidth Measurement ..................................................................................... 16 7.2.1. Test Limit ......................................................................................................................... 16 7.2.2. Test Procedure used ....................................................................................................... 16 7.2.3. Test Setting ..................................................................................................................... 16 7.2.4. Test Setup ....................................................................................................................... 16 7.2.5. Test Result ...................................................................................................................... 17 7.3. Output Power Measurement ................................................................................................ 20 7.3.1. Test Limit ......................................................................................................................... 20 7.3.2. Test Procedure Used ....................................................................................................... 20 7.3.3. Test Setting ..................................................................................................................... 20 7.3.4. Test Setup ....................................................................................................................... 20 7.3.5. Test Result of Output Power ............................................................................................ 21 7.4. Power Spectral Dens…

Text truncated - open the document above for the full version.

MRT Technology (Taiwan) Co., Ltd Report No.: 1908TW8501-U2 Phone: +886-3-3288388 Report Version: 1.0 Fax: +886-3-3288918 Issue Date: 2019-09-19 Web: www.mrt-cert.com FCC ID: 2AH2P-BC90019 Page Number: 1 of 51 FCC ID: 2AH2P-BC90019 APPLICANT: DECATHLON USA LLC Application Type: Certification Product: GPS BIKE COMPUTER Model No.: BC900 FCC Classification: (DTS) Digital Transmission System FCC Rule Part(s): Part 15.247 Test Procedure(s): ANSI C63.10-2013, KDB 558074 D01v05r02 Received Date: August 2, 2019 Test Date: August 28 ~ September 5, 2019 MEASUREMENT REPORT FCC PART 15.247 & IC RSS-247 Bluetooth V4.2 LE The test results only relate to the tested sample. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 558074. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. Tested By : ( Peter Syu ) Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker) Report No.: 1908TW8501-U2 FCC ID: 2AH2P-BC90019 Page Number: 2 of 51 Revision History Report No. Version Description Issue Date Note 1908TW8501-U2 1.0 Original Report 2019-09-19 Report No.: 1908TW8501-U2 FCC ID: 2AH2P-BC90019 Page Number: 3 of 51 CONTENTS Description Page §2.1033 General Information ......................................................................................................... 5 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope .................................................................................................................................... 6 1.2. MRT Test Location ................................................................................................................ 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description .......................................................................................................... 7 2.2. Product Specification Subjective to this Standard .................................................................. 7 2.3. Test Mode ............................................................................................................................. 7 2.4. Operation Frequency / Channel List ...................................................................................... 8 2.5. Test Configuration ................................................................................................................. 9 2.6. Test Software ........................................................................................................................ 9 2.7. EMI Suppression Device(s)/Modifications ............................................................................. 9 2.8. Labeling Requirements ......................................................................................................... 9 3. DESCRIPTION of TEST ........................................................................................................ 10 3.1. Evaluation Procedure .......................................................................................................... 10 3.2. AC Line Conducted Emissions ............................................................................................ 10 3.3. Radiated Emissions ............................................................................................................ 11 4. ANTENNA REQUIREMENTS ................................................................................................ 12 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 13 6. MEASUREMENT UNCERTAINTY ......................................................................................... 14 7. TEST RESULT ...................................................................................................................... 15 7.1. Summary ............................................................................................................................. 15 7.2. Occupied Bandwidth Measurement ..................................................................................... 16 7.2.1. Test Limit ......................................................................................................................... 16 7.2.2. Test Procedure used ....................................................................................................... 16 7.2.3. Test Setting ..................................................................................................................... 16 7.2.4. Test Setup ....................................................................................................................... 16 7.2.5. Test Result ...................................................................................................................... 17 7.3. Output Power Measurement ................................................................................................ 20 7.3.1. Test Limit ......................................................................................................................... 20 7.3.2. Test Procedure Used ....................................................................................................... 20 7.3.3. Test Setting ..................................................................................................................... 20 7.3.4. Test Setup ....................................................................................................................... 20 7.3.5. Test Result of Output Power ............................................................................................ 21…

Text truncated - open the document above for the full version.