2AHMR-TB-01Bluetooth module

TB-01SpecificationV1.0 Copyright©2019ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved I TB-01Specification VersionV1.0 Copyright©2019 TB-01 Specification V1.0 Copyright © 2019 Shenzhen Ai-Thinker Technology Co., Ltd All Rights Reserved II Disclaimer and Copyright Notice The information in this article, including URL addresses for reference, is subject to change without notice. This document is provided "as is" without warranty of any kind, including any warranty of merchantability, fitness for a particular purpose, or non-infringement, and any warranty of any proposal, specification, or sample mentioned elsewhere. No liability is assumed in this document, including any infringement of any patent rights arising out of the use of the information in this document. No license is granted by estoppel or otherwise in this document, either express or implied. The test data obtained in this article are all obtained from the testing performed by Anxinke Labs. Actual results may vary slightly. The Bluetooth Alliance member logo is owned by the Bluetooth Alliance. All trademark names, trademarks and registered trademarks mentioned in this article are the property of their respective owners and are hereby declared. The final interpretation right belongs to Shenzhen Anxinke Technology Co., Ltd. Pay attention The contents of this manual may be changed due to product version upgrades or other reasons. Shenzhen Anxinke Technology Co., Ltd. reserves the right to modify the contents of this manual without any notice or prompt. This manual is only used as a guide. Shenzhen Anxin Ke Technology Co., Ltd. makes every effort to provide accurate information in this manual, but Shenzhen An Xin Ke Technology Co., Ltd. does not ensure that the content of the manual is completely error-free. All statements and information in this manual And recommendations do not constitute any express or implied warranty. FCC WARNING STATEMENT Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. TB-01SpecificationV1.0 Copyright©2019ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved III Documentdevelopment/revision/revocationresume VersionDateRevisedcontentMakerApprove V1.02019.11.25Firstdeveloped YijiXie TB-01SpecificationV1.0 Copyright©2019ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved IV CONTENT 一、INTRODUCTION ....................................................................................... 错误！未定义书签。 二、SPECIFICATION ........................................................................................ 错误！未定义书签。 三、DIMENSION ............................................................................................. 错误！未定义书签。 四、PINDEFINITION .................................................................................................................. VIII 五、SCHEMATIC ............................................................................................... 错误！未定义书签。 六、DESIGNGUIDE ........................................................................................... 错误！未定义书签。 七、REFLOWPROFILE ............................................................................................................... XIII 八、PACKAGING ............................................................................................... 错误！未定义书签。 九、CONTACTUS ............................................................................................. 错误！未定义书签。 TB-01SpecificationV1.0 Copyright©2019ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved V 1.INTRODUCTION TheTB-01intelligentlightingmoduleisaBluetoothmodulebasedontheEP2S12F40chip andcompatiblewithBT4.2low-powerTmallGenieMesh.ThismodulesupportstheBluetooth moduledirectlycontrolledbyTmallGenieandhasaBluetoothmeshnetworkingfunction. Peer-to-peernetworkcommunication,usingBluetoothbroadcastforcommunication,can ensuretimelyresponseinthecaseofmultipledevices.Itismainlyusedinintelligentlight control,whichcanmeettherequirementsoflowpowerconsumption,lowlatency,and short-rangewirelessdatacommunication. Features CanbedirectlycontrolledbyTmallElfwithoutagateway 2.0mmpitchpinverticalsolderpackage 2positivewhitewarmwhitePWMoutputs Withon-boardantenna,noneedtodesignantenna Brightness(dutycycle)adjustmentrange5%-100% Factorydefault50%dutycycleforcoolandwarmcolors PWMoutputpower1KHz Withnightlightfunction Withwallswitchtoswitchcolortemperaturefunction TB-01SpecificationV1.0 Copyright©2019ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved VI LIST1MainParameters ModelNameTB-01 Size 22.0*14.0*2.0(±0.2)MM WirelessStandardBluetoothV4.2 FrequencyRange2400~2483.…

Text truncated - open the document above for the full version.

Date: Dec. 30, 2019 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AHMR-TB-01 Product Name: Bluetooth module Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: Su Facheng Title: Engineer Company: Shenzhen Ai-Thinker Technology Co., Ltd

Date: Dec. 30, 2019 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: Su Facheng Title: Engineer Company: Shenzhen Ai-Thinker Technology Co., Ltd

Date: Dec. 30, 2019 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen CTB Testing Technology Co., Ltd. Add: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Community, Xinqiao Street, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Ai-Thinker Technology Co., Ltd Add: 6/F, Block C2, Huafeng Industrial Park, Hangcheng Road, Baoan district, Shenzhen China <Signature> Name: Su Facheng Title: Engineer Company: Shenzhen Ai-Thinker Technology Co., Ltd

Single Modular approval Declaration letter We, Shenzhen Ai-Thinker Technology Co., Ltd apply single modular approval for Product Na me: Bluetooth module MODEL No.: TB-01 FCC ID: 2AHMR-TB-01 According to 996369 D01 Module Equip Auth Guide v01r04 and 15.212 requirement: 1)The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must beon the module assembly; Answer ：Yes ； shielded for both side 2)The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; Answer ：Yes ；All inputs to the modules are buffered through logic or microprocessor inputs. 3)Th e modular transmitter must have its own power supply regulation. Answer ：Yes ；A low drop out regulator is used for modular power supply regulation. 4)The module must contain a permanently attached antenna, or contain a unique antenna connector, an d be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); Answer ：Yes ；Device is equipped with Integral PCB antenna. (5)The module must demonstrate compliance in a stand-alone configuration; Answer ：Yes，distance between modular and all AEs are longer than 10cm ，refer to setup photo. (6)The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); Answer ：Yes ；The modular has a permanent fixed label, and below statement was listed in the User Manual;The host device must be labeled to display the FCC ID of the module Contains FCC ID: 2AHMR-TB-01 (7)The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; Answer ：Yes ；The module comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee, Refer to test report and user manual . (8)The module must comply with RF exposure requirements Answer ：Yes ；Transmitter meets MPE calculation of 47 CFR 1.1307 . Refer to MPE Reports and Refer to modular installation manual <Signature> Name: Su Facheng Title: Engineer Company: Shenzhen Ai-Thinker Technology Co., Ltd

M/N: TB-01 M/N: TB-01 M/N: TB-01

FCC ID LABEL: Label Location: FCC ID: 2AHMR-TB-01 Long:0.8cm Width:0.2cm

M/N: ESP-13 PCB A NT.

Global United Technology Services Co., Ltd. Report No.: GTS201912000285F01 Authorized Signature: Robinson Lo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 39 TEST Report (Bluetooth) Applicant: Shenzhen Ai-Thinker Technology Co., Ltd. Address of Applicant: 6/F, Block C2, Huafeng Industrial Park, Hangcheng Road, Baoan district, Shenzhen China Manufacturer: Shenzhen Ai-Thinker Technology Co., Ltd. Address of Manufacturer: 6/F, Block C2, Huafeng Industrial Park, Hangcheng Road, Baoan district, Shenzhen China Equipment Under Test (EUT) Product Name: Bluetooth module Model No.: TB-01 FCC ID: 2AHMR-TB-01 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: Dec 23, 2019 Date of Test: Dec 23, 2019-Dec 27, 2019 Date of report issued: Dec 27, 2019 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTS201912000285F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 39 2 Version Version No. Date Description 00 Dec 27, 2019 Original Prepared By: Date: Dec 27, 2019 Project Engineer Check By: Date: Dec 27, 2019 Reviewer Report No.: GTS201912000285F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 39 3 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 VERSION ...................................................................................................................................................2 3 CONTENTS ...............................................................................................................................................3 4 TEST SUMMARY ......................................................................................................................................4 5 GENERAL INFORMATION .......................................................................................................................5 5.1 GENERAL DESCRIPTION OF EUT ..........................................................................................................5 5.2 TEST MODE .........................................................................................................................................7 5.3 DESCRIPTION OF SUPPORT UNITS ........................................................................................................7 5.4 DEVIATION FROM STANDARDS ..............................................................................................................7 5.5 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................7 5.6 TEST FACILITY ....................................................................................................................................7 5.7 TEST LOCATION ..................................................................................................................................7 6 TEST INSTRUMENTS LIST ......................................................................................................................8 7 TEST RESULTS AND MEASUREMENT DATA .....................................................................................10 7.1 ANTENNA REQUIREMENT ....................................................................................................................10 7.2 CONDUCTED EMISSIONS ....................................................................................................................11 7.3 CONDUCTED OUTPUT POWER ............................................................................................................14 7.4 CHANNEL BANDWIDTH .......................................................................................................................15 7.5 POWER SPECTRAL DENSITY ..............................................................................................................18 7.6 BAND EDGES .....................................................................................................................................21 7.6.1 Conducted Emission Method ......................................................................................................21 7.6.2 Radiated Emission Method .........................................................................................................22 7.7 SPURIOUS EMISSION .........................................................................................................................24 7.7.1 Conducted Emission Method ......................................................................................................24 7.7.2 Radiated Emission Method .........................................................................................................27 8 TEST SETUP PHOTO .............................................................................................................................35 9 EUT CONSTRUCTIONAL DETAILS .......................................................................................................37 Report No.: GTS201912000285F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong…

Text truncated - open the document above for the full version.

M/N: TB-01 Radiated Emission test M/N: TB-01 Conducted Emission test