2AHXJ-PRO200Pro-200

Mopeka Products, LLC Rev 2026-04-24 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-24-2026 Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) FCC ID: 2AHXJ-PRO200 Part 2.911(d)(5)(i) [Mopeka Products, LLC] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment and does not contain anti-virus software or cybersecurity software prohibited from receiving an equipment authorization pursuant to 47 CFR 2.903, KDB 986446 D01 Covered Equipment Guidance, and FCC Covered List (www.fcc.gov/supplychain/coveredlist). Part 2.911(d)(5)(ii) [Mopeka Products, LLC] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, _________________ Name: Jonathan Kaufmann Date: 2026-07-24

Mopeka Products, LLC Declaration of Conformity We Name: Mopeka Products, LLC Address: 1223 Industrial Drive, Suite A New Braunfels, TX 78130 Declare that: Product:Pro-200 FCC ID:2AHXJ-PRO200 Model:PRO200 Brand:Mopeka Product which bears the above FCC ID is also compliant with the FCC requirements for sDOC. And the sDOC procedure shall be carried out prior to marketing the device in the US. Sincerely, _________________ Name: Jonathan Kaufmann Date: 2026-07-24

Mopeka Products, LLC U.S. Agent Designation for Service of Process (Applicant is Both Grantee and U.S. Agent) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTENTION: FCC Certification – Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: Mopeka Products, LLC FRN #: 0025181710 Grantee Code: 2AHXJ Contact Name: Jonathan Kaufmann Street Address: 1223 Industrial St Suite A City/Province/Zip: New Braunfels, Texas, 78130 Telephone No: (210) 204-6629 Email: [email protected] Applicant Signature 1 : Date:2026-07-24 Signed by (Printed Name/Title): Jonathan L Kaufmann 1 - Letters must be placed on appropriate letterhead. The signee for the applicant must be one of the following: Applicant (grantee) contact of record in the FCC’s authorization system, or authorized officers or employee of the applicant (grantee).

Mopeka Products, LLC Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: 2AHXJ-PRO200 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: 1.Block Diagram 2.Schematics 3.Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, _________________ Name: Jonathan Kaufmann Email: [email protected] Date:2026-07-24

Mopeka Products, LLC Short Term Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: 2AHXJ-PRO200 Pursuant to sections 0.457 and 0.459 of CFR 47 Commission’s policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days: 1.External Photos 2.Internal Photos 3.Test Setup Photos 4.User Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, _________________ Name: Jonathan Kaufmann Email: [email protected] Date: 2026-07-24

Mopeka Products, LLC Declaration of Authorization We Name: Mopeka Products, LLC Address: 1223 Industrial Drive, Suite A New Braunfels, TX 78130 Declare that: Name Representative of agent:Marlin Chen Agent Company name:MRT Technology (Suzhou) Co., Ltd Address:D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone City:Suzhou Country:China is authorized to apply for Certification of the following product(s): Product:Pro-200 FCC ID:2AHXJ-PRO200 Model No.:PRO200 Sincerely, ________________ Name: Jonathan Kaufmann Email: [email protected] Date: 2026-07-24

12.7 25.4 MATERIAL = ZEBRA Z-ULTIMATE 2000T OR 3000T, WHITE, 5095 OR 5100 RESIN (UL 969 APPROVED) FCC ID: 2AHXJ-PRO200 REVISIONS ZONEREV.ECO#DESCRIPTION DATE (YYYY.MM.DD) -A-RELEASE2026.08.17 B A A B 2 3 4 4 3 21 1 M2006353 A REVISIONDRAWING NUMBER 56 C D C D 6 5 PROPRIETARY and CONFIDENTIAL This document, including the information hereon, is the property of MOPEKA PRODUCTS LLC., its subsidiaries, and/or affiliates. It may be used only to purchase or supply goods and/or services relative to MOPEKA PRODUCTS LLC and must be returned upon MOPEKA PRODUCTS LLC request. It is CONFIDENTIAL and must be maintained in confidence. It may not be reproduced, copied or have other items prepared therefrom and may not be disclosed to others, in whole or in part, without MOPEKA PRODUCTS LLC prior written consent. ALL RIGHTS RESERVED. - -- - -- 1 OF 1 SHEET 5:1 AND NOTED - M2006353 M2006353 2026.08.17RM APPROVED 2 A METRIC M2006353.SLDPRT LABEL; FCC PRO200 CAD FILE UNLESS OTHERWISE SPECIFIED PRODUCE PART FROM CAD MODEL M2006353.SLDPRT, ALL NON-TOLERANCED DIMENSIONS ARE BASIC TO THE CAD MODEL. REFER TO THE DRAWING FOR ASSOCIATED TOLERANCES, DATUMS AND FEATURE CONTROLS. PART NUMBER DESCRIPTION DO NOT SCALE DRAWING. DIMENSIONING AND TOLERANCING PER ASME Y14.5 - 2009 APPLY. A3 ENGINEER APPROVED 1 DRAWN APPROVALSDATE (YYYY.MM.DD) REVISION DRAWING NUMBER SHEET SIZESCALE Copyright 2020 Mopeka Products LLC. All rights reserved.

MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1025040-U401 Phone: +86-512-66308358 Report Version: V02 Web: www.mrt-cert.com Issue Date: 2026-09-17 Template Version: 3.0 1 of 10 RF Exposure Evaluation Declaration FCC ID: 2AHXJ-PRO200 Applicant: Mopeka Products, LLC Product: Pro-200 Model No.: PRO200 Brand Name: Mopeka Standards: FCC Part 2.1091 KDB 447498 D04 v01 Result: Complies Evaluation Date: 2026-07-17 Prepared By: Nora Qin Reviewed By: Vincent Yu Approved By: Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report. Testing was performed in accordance with the applicable measurement procedures. The test results reported herein apply only to the specific item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1025040-U401 2 of 10 Revision History Report No. Version Description Issue Date Note R26S1025040-U401 V01 Initial Report 2026-08-18 Invalid R26S1025040-U401 V02 Update Antenna Gain 2026-09-17 Valid Report No.: R26S1025040-U401 3 of 10 CONTENTS Description Page 1. General Information ............................................................................................................................... 4 1.1. Applicant....................................................................................................................................... 4 1.2. Manufacturer ................................................................................................................................ 4 1.3. Testing Facility .............................................................................................................................. 4 1.4. Product Information ...................................................................................................................... 5 1.5. Antenna Details ............................................................................................................................ 5 1.6. Device Classification .................................................................................................................... 5 1.7. Applied Standards ........................................................................................................................ 5 2. RF Exposure Evaluation ........................................................................................................................ 6 2.1. Limits ............................................................................................................................................ 6 2.2. MPE Exemptions .......................................................................................................................... 7 2.3. Calculated Result ....................................................................................................................... 10 Report No.: R26S1025040-U401 4 of 10 1. General Information 1.1. Applicant Mopeka Products, LLC 1223 Industrial Drive, Suite A New Braunfels, TX 78130 1.2. Manufacturer Mopeka Products, LLC 1223 Industrial Drive, Suite A New Braunfels, TX 78130 1.3. Testing Facility Test Site - MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Location (Suzhou - Wujiang) Building 1, No.1 Xingdong Road, Wujiang, Suzhou, Jiangsu, People’s Republic of China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 Test Site - MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 FCC: CN1284 ISED: CN0105 Report No.: R26S1025040-U401 5 of 10 1.4. Product Information Product Name Pro-200 Model No. PRO200 Bluetooth Specification BLE_1 Mbps Antenna Specification Refer to clause 1.5 Operating Temperature -40 ~ 85 °C Power Type DC 12 V Note: The information of the EUT (Equipment Under Test) was provided by the manufacturer. The accuracy, completeness, and validity of the information are solely the responsibility of the manufacturer. 1.5. Antenna Details Test Mode Frequency Range (MHz) Antenna Type Antenna Gain (dBi) BLE 2400 ~ 2483.5 PCB Antenna 0.91 1.6. Device Classification According to the user manual, this device is classified as a Mobile Device. So, the RF exposure evaluation requirements of § 2.1091 for mobile device exposure conditions subject to MPE limits. 1.7. Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: ⚫ FCC Part 2.1091 ⚫ KDB 447498 D04 Interim General RF Exposure Guidance v01 Report No.: R26S1025040-U401 6 of 10 2. RF Exposure Evaluation 2.1. Limits According to FCC §1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b) Limits For Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 0.3 ~ 3.0 614 1.63 *(100) ≤ 6 3.0 ~ 30 1842/f 4.89/f *(900/f 2 ) < 6 30 ~ 300 61.4 0.163 1.0 < 6 300 ~ 1500 -- -- f/300 < 6 1500 ~ 100000 -- -- 5 < 6 (B) Limits for General Population/ Uncontrolled Exposures 0.3 ~ 1.34 614 1.63 *(100) < 30 1.34 ~ 30 824/f 2.19/f *(180/f 2 ) < 30 30 ~ 300 27.5 0.073 0.2 < 30 300 ~ 1500 -- -- f/1500 < 30 1500 ~ 100000 -- -- 1.0 < 30 f = frequency in MHz. * = Plane-wave equivalent power density. Report No.: R26S1025040-U401 7 of 10 2.2. MPE Exemptions For single RF sources (i.e., an…

Text truncated - open the document above for the full version.

MOPEKA PRODUCTS LLC | Pro200 Antenna Report | 1 / 3 MOPEKA PRODUCTS LLC Mopeka Pro200 Antenna Report Meandered PCB monopole | Reference design and simulation Permanent attachment. The antenna is etched directly into the PCB copper and permanently attached to the device. It is not a separately replaceable component, and the product has no detachable RF antenna connector. This construction uses the permanently attached antenna provision of 47 CFR 15.203. Nordic nRF52840 USB Dongle reference PCA10059 v1.0.0 / PCB 400250 Unshorted printed meandered monopole. Native layout: 15 June 2018; schematic/layout PDF pp. 1-3. Trace width: 0.254 mm. Copper envelope: 10.346 x 5.981 mm. Board: approximately 46.04 x 15.24 mm. Two layers; 2.0 mm FR-4 core in the CAD stack. Nordic's published hardware files and dimension drawing provide the geometry reference. Mopeka antenna gain is calculated from the product model on the following pages. Design comparison. PRO200 rev D shares the ten meander-turn segments and the 0.254 mm trace width of PCA10059. Its feed- side extent, ground plane, PCB stack and matching network are product-specific. PCA10040 provides an additional printed- monopole reference. Mopeka PRO200 antenna Top copper / rev D M2006201D / M2006202D Trace width: 0.254 mm. Copper envelope: 10.346 x 5.047 mm. Centerline: 29.674 mm from A1 feed. No grounded shorting arm. Board: 36.00 x 39.26 mm. Four layers; FR-4/prepreg, approximately 0.8 mm CAD stack. Ground-envelope inset; inner voids omitted. Blue: antenna projection. Construction and feed. Integral copper for BLE channel centers 2402-2480 MHz. The nRF52810-QCAA ANT pin 19 feeds C15 0.8 pF shunt and L3 3.9 nH series; C36 is not fitted. The radiator lies over a copper-recessed region on all layers. The rev D layout incorporates the antenna shortening. Dimensions follow native layout coordinates. The main-route length excludes matching pads and extra feed copper; its starting point is the A1 feed. Simulation result. Highest sampled total gain is 0.91 dBi at 2480 MHz for the bare PCB model. Results cover 2402, 2440 and 2480 MHz on a 3- degree spherical angular grid. The model configuration and numerical results follow. MOPEKA PRODUCTS LLC | Pro200 Antenna Report | 2 / 3 MOPEKA PRODUCTS LLC | PRO200 Copper based Full Wave Analysis PRO200 Rev D | M2006201D | Bare PCB | 2480 MHz M2006201D copper and native layer stack. Antenna- side feed at L3. Model loss tangent: 0.02 at 2440 MHz. Peak gain 0.91 dBi S11 at 50 ohms -3.11 dB Radiation efficiency 74.9% X/Y: PCB plane. Z: board normal. Pattern radius is normalized field amplitude. Enclosure, cable, potting, mounting structures and populated component loads are excluded. Results MHzGain dBiRealized dBiS11 dBEfficiency 24020.75-1.99-3.3172.4% 24400.83-1.96-3.2573.6% 24800.91-2.00-3.1174.9% HTML result set: pro200_d_m127. Total gain uses accepted feed power; realized gain includes mismatch at the 50-ohm port. Reported peaks are sampled over a 3-degree spherical grid at the three listed frequencies. Values are simulated. MOPEKA PRODUCTS LLC | Pro200 Antenna Report | 3 / 3 MOPEKA PRODUCTS LLC | PRO200 Radiation Pattern Results Principal Plane Radiation Patterns Near Field at 2440 MHz Computed electric-field magnitude 0.397 mm above top copper. Both views use the plane maximum as 0 dB. The field map presents relative electric- field amplitude. Source Geometry PCB M2006201D. Four copper layers retain the released board geometry in the electromagnetic model. This illustration shows the antenna and its local ground region. openEMS 0.37.0rc2, Cartesian FDTD and near-to-far-field transformation. PCB dielectric inputs: relative permittivity 4.1 / 4.5 / 4.1 and loss tangent 0.02 at 2440 MHz. Hardware correlation and production-tolerance sweeps are outside this model. Source: PRO200 simulation index.html, viewer_data.js, simulation_report.md and verification.json. The displayed result set and original image assets are retained together.

MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1025040-U201 Phone: +86-512-66308358 Report Version: V02 Web: www.mrt-cert.com Issue Date: 2026-09-17 Template Version: 3.0 1 of 53 RF MEASUREMENT REPORT FCC ID: 2AHXJ-PRO200 Applicant: Mopeka Products, LLC Product: Pro-200 Model No.: PRO200 Brand Name: Mopeka FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15 Subpart C (Section 15.247) Result: Complies Received Date: 2026-04-07 Test Date: 2026-05-15 ~ 2026-08-27 Prepared By: Nora Qin Reviewed By: Vincent Yu Approved By: Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report. Testing was performed in accordance with the applicable measurement procedures. The test results reported herein apply only to the specific item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1025040-U201 2 of 53 Revision History Report No. Version Description Issue Date Note R26S1025040-U201 V01 Initial Report 2026-08-28 Invalid R26S1025040-U201 V02 Update Antenna Gain 2026-09-17 Valid Report No.: R26S1025040-U201 3 of 53 CONTENTS Description Page 1. General Information ................................................................................................................................ 5 1.1. Applicant ...................................................................................................................................... 5 1.2. Manufacturer ................................................................................................................................ 5 1.3. Testing Facility ............................................................................................................................. 5 1.4. Product Information ...................................................................................................................... 6 1.5. Radio Specification under Test .................................................................................................... 6 1.6. Working Frequencies ................................................................................................................... 7 2. Test Configuration ................................................................................................................................... 8 2.1. Test Mode..................................................................................................................................... 8 2.2. Test System Connection Diagram ............................................................................................... 8 2.3. Test Software ............................................................................................................................... 8 2.4. Applied Standards ........................................................................................................................ 9 2.5. Test Environment Condition ......................................................................................................... 9 3. Antenna Requirements ......................................................................................................................... 10 4. Measuring Instrument ........................................................................................................................... 11 5. Decision Rules and Measurement Uncertainty .................................................................................. 12 5.1. Decision Rules ........................................................................................................................... 12 5.2. Measurement Uncertainty .......................................................................................................... 12 6. Test Result .............................................................................................................................................. 13 6.1. Summary .................................................................................................................................... 13 6.2. 6 dB Bandwidth Measurement ................................................................................................... 14 6.2.1. Test Limit .................................................................................................................................... 14 6.2.2. Test Procedure ........................................................................................................................... 14 6.2.3. Test Setting ................................................................................................................................ 14 6.2.4. Test Setup .................................................................................................................................. 14 6.2.5. Test Result ................................................................................................................................. 14 6.3. Output Power Measurement ...................................................................................................... 15 6.3.1. Test Limit .................................................................................................................................... 15 6.3.2. Test Procedure ........................................................................................................................... 15 6.3.3. Test Setting ................................................................................................................................ 15 6.3.4. Test Setup .................................................................................................................................. 15 6.3.5. Test Result ....................................................................................................…

Text truncated - open the document above for the full version.