2AJQ6MMF-15088FEED HUB UNIVERSAL

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Warning Statements: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L' appareil ne doit pas produire de brouillage; (2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement. Radio Frequency Exposure Statement for IC This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. Cet équipement est conforme aux limites d'exposition IC définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et la carrosserie.

EBSCO Industries Inc., DBA PRADCO Outdoor Brands 5724 Highway 280 East Birmingham, Alabama 35242, United States (Jun. 19, 2024) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, (Applicant signature) (Daniel Wilson)

Report No.: AGC16184240502AP02 Page 1 of 3 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC16184240502AP02 Page 2 of 3 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC16184240502AP02 Page 3 of 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID&IC Label Location 60mm&60mm

Report No.: AGC16184240502AP02 Page 1 of 6 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC16184240502AP02 Page 2 of 6 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC16184240502AP02 Page 3 of 6 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) Report No.: AGC16184240502AP02 Page 4 of 6 INTERNAL VIEW OF EUT (FIGURE 5) INTERNAL VIEW OF EUT (FIGURE 6) Report No.: AGC16184240502AP02 Page 5 of 6 INTERNAL VIEW OF EUT (FIGURE 7) INTERNAL VIEW OF EUT (FIGURE 8) Antenna Report No.: AGC16184240502AP02 Page 6 of 6 INTERNAL VIEW OF EUT (FIGURE 9) INTERNAL VIEW OF EUT (FIGURE 10) ****************************************End of Report*************************************

Page 1 of 12 RF Exposure Report Report No.: AGC16184240502FH01 FCC ID : 2AJQ6MMF-15088 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : FEED HUB UNIVERSAL BRAND NAME : MOULTRIE MOBILE MODEL NAME : MMF-15088 APPLICANT : EBSCO Industries Inc., DBA PRADCO Outdoor Brands DATE OF ISSUE : Jun. 06, 2024 STANDARD(S) : FCC Part 2 Subpart J §2.1091 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC16184240502FH01 Page 2 of 12 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 06, 2024 Valid Initial Release Report No.: AGC16184240502FH01 Page 3 of 12 Table of Contents 1. General Information ........................................................................................................................................ 4 2. Product Information ........................................................................................................................................ 5 2.1 Product Technical Description ................................................................................................................... 5 3. Test Environment ............................................................................................................................................ 6 3.1 Address Of The Test Laboratory ............................................................................................................... 6 3.2 Test Facility ................................................................................................................................................ 6 3.3 Environmental Conditions ......................................................................................................................... 7 4. Portable Device Evaluation Method and Limit ............................................................................................. 8 5. Mobile Device Evaluation Method and Limit ................................................................................................ 9 6. Measurement Results ................................................................................................................................... 10 7. Measurement Evaluation .............................................................................................................................. 12 Report No.: AGC16184240502FH01 Page 4 of 12 1. General Information Applicant EBSCO Industries Inc., DBA PRADCO Outdoor Brands Address 5724 Highway 280 East Birmingham, Alabama 35242, United States Manufacturer Plastic Research and Development Corporation DBA Moultrie Feeders Address 15 Block, Third industrial Area, Longxi Village Longgang District, Shenzhen, China Factory Plastic Research and Development Corporation DBA Moultrie Feeders Address 15 Block, Third industrial Area, Longxi Village Longgang District, Shenzhen, China Product Designation FEED HUB UNIVERSAL Brand Name MOULTRIE MOBILE Test Model MMF-15088 Series Model(s) N/A Difference Description N/A Date of receipt of test item May 21, 2024 Date of Test May 23, 2024 to Jun. 06, 2024 Deviation from Standard No any deviation from the test method Condition of Test Sample Normal Test Result Pass Test Report Form No AGCER-FCC-RF Exposure-V1 Note: The test results of this report relate only to the tested sample identified in this report. Prepared By Bibo Zhang (Project Engineer) Jun. 06, 2024 Reviewed By Calvin Liu (Reviewer) Jun. 06, 2024 Approved By Max Zhang (Authorized Officer) Jun. 06, 2024 Report No.: AGC16184240502FH01 Page 5 of 12 2. Product Information 2.1 Product Technical Description Frequency Band (Operating) FSK: 915MHz LTE: LTE Band 2: 1850-1910MHz; LTE Band 4: 1710-1755 MHz; LTE Band 5: 824-849MHz; LTE Band 8: 897.5-900.5MHz; LTE Band 12: 699-716MHz; LTE Band 13: 777-787MHz; LTE Band 25: 1850-1915MHz; LTE Band 26A: 824-849MHz; LTE Band 26B: 814-824MHz; LTE Band 66: 1710-1780MHz; LTE Band 85: 698-716MHz; NB-IOT: LTE Band 2: 1850-1910MHz; LTE Band 4: 1710-1755 MHz; LTE Band 5: 824-849MHz; LTE Band 8: 897.5-900.5MHz; LTE Band 12: 699-716MHz; LTE Band 13: 777-787MHz; LTE Band 25: 1850-1915MHz; LTE Band 66: 1710-1780MHz; LTE Band 71: 663-698MHz; LTE Band 85: 698-716MHz; Hardware Version V1.0 Software Version V1.0 Modulation Type FSK/QPSK/16QAM/ BPSK/QPSK Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Antenna Designation Chip Antenna Antenna Gain FSK -1dBi; LTE: LTE Band 2: 0.64dBi; LTE Band 4: 0.59dBi; LTE Band 5: 0.05dBi; LTE Band 8: 0.05dBi; LTE Band 12: -2.2dBi; LTE Band 13: -2.2dBi; LTE Band 25: 0.59dBi; LTE Band 26A: 0.05dBi; LTE Band 26B: 0.05dBi; LTE Band 66: 0.59dBi; LTE Band 85: -2.2dBi; NB-IOT: LTE Band 2: 0.64dBi; LTE Band 4: 0.59dBi; LTE Band 5: 0.05dBi; LTE Band 8: 0.05dBi; LTE Band 12: -2.2dBi; LTE Band 13: -2.2dBi; LTE Band 25: 0.59dBi; LTE Band 66: 0.59dBi; LTE Band 71: -2.2dBi; LTE Band 85: -2.2dBi; Minimum Assessment Distance 20cm Evaluation Applied MPE Evaluation SAR Evaluation Report No.: AGC16184240502FH01 Page 6 of 12 3. Test Environment 3.1 Address Of The Test Laboratory Laboratory: Attestation of Global Compliance (Shenzhen) Co., Ltd. Address: 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China 3.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5488 Attestation of Global Compliance (Shenzhen) Co., Ltd. has been assessed and proved to follow CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories.) A2LA-Lab Cert. No.: 5054.02 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testin…

Text truncated - open the document above for the full version.

AT7020-AR90HAAT/LF REV:5 PAGE:1/11 ACX Advanced Ceramic X Features  Monolithic SMD with small, low-profile and light-weight type.  Wide bandwidth  RoHS compliant Applications  Low power radio applications for 902~928MHz. Specifications Part Number Frequency Range (MHz) Peak Gain (dBi typ.) Average Gain (dBi typ.) VSWR Impedance AT7020 -AR90HAA_ 902~928 -1.0 (XZ-total) -4.0 (XZ-total) 2.2 max. 50  Q’ty/Reel (pcs) : 1,000 pcs Operating Temperature Range : -40 ~ +85 o C Storage Temperature Range : -40 ~ +85 o C Storage Period : 12 months max. Power Capacity : 2W max. Part Number  Type AT : Antenna  Dimensions ( L × W ) 7.0× 2.0 mm  Material Code A  Frequency Range R90=915MHz  Specification Code HAA  Packaging T: Tape & Reel B: Bulk  Soldering /LF=lead-free Terminal Configuration No. Terminal Name No. Terminal Name  Feeding Point  NC AT7020 Series Multilayer Chip Antenna   AT 7020 - A R90 HAA        AT7020-AR90HAAT/LF REV:5 PAGE:2/11 ACX Advanced Ceramic X Dimensions and Recommended PC Board Pattern Mark L W T a Dimensions 7.0±0.2 2.0±0.2 0.8+ 0.1/-0.2 0.5±0.3 Typical Electrical Characteristics (T=25 o C)  Test Board-Type A Unit : mm L W a T Antenna No Ground Ground 20mm 19mm 40mm 9.5mm 50Feed Line AT7020-AR90HAAT/LF REV:5 PAGE:3/11 ACX Advanced Ceramic X 0.60.70.80.91.01.11.20.51.3 -40 -35 -30 -25 -20 -15 -10 -5 -45 0 freq, GHz dB(S(1,1)) m1 m2 m3 m1 freq= dB(S(1,1))=-11.21 7 902.0MHz m2 freq= dB(S(1,1))=-11.80 7 928.0MHz m3 freq= dB(S(1,1))=-43.25 7 915.0MHz With matching-Type A *Line width should be designed to match 50 characteristic impedance, depending on PCB material and thickness. Return Loss (with matching)-Type A (Matching circuit and component values will be different, depending on PCB layout) * * * 1.8 6.0 8.0 1.0 5.1 7.1 2.5 0.5 0.5 pF 10 nH 4.7 nH Matching circuits AT7020-AR90HAAT/LF REV:5 PAGE:4/11 ACX Advanced Ceramic X Radiation Patterns-Type A XY cut @915MHz Vertical Horizontal XZ cut @915MHz Vertical Horizontal YZ cut @915MHz Vertical Horizontal XY-V/XY-H XZ-V/XZ-H YZ-V/YZ-H 180 o 270 o 0 o 90 o X Z Y XY-cut scanning direction 180 o 270 o 0 o 90 o X Z Y XZ-cut scanning direction 180 o 270 o 0 o 90 o X Y Z YZ-cut scanning direction AT7020-AR90HAAT/LF REV:5 PAGE:5/11 ACX Advanced Ceramic X Test Board-Type B With matching-Type B *Line width should be designed to match 50 characteristic impedance, depending on PCB material and thickness. Antenna No Ground Ground 20mm 19mm 40mm 9.5mm 50Feed Line (Matching circuit and component values will be different, depending on PCB layout) * * * 2.0 5.5 8.0 1.0 6.0 7.5 4.0 0.5 5.6 pF 2.2 nH Matching circuits 1.0 5.5 0.5 Ground Ground AT7020-AR90HAAT/LF REV:5 PAGE:6/11 ACX Advanced Ceramic X 0.60.70.80.91.01.11.20.51.3 -20 -15 -10 -5 -25 0 freq, GHz dB(S(1,1)) m1 m2 m3 m1 freq= dB(S(1,1))=-13.786 902.0MHz m2 freq= dB(S(1,1))=-15.038 928.0MHz m3 freq= dB(S(1,1))=-20.399 915.0MHz Return Loss (with matching)-Type B AT7020-AR90HAAT/LF REV:5 PAGE:7/11 ACX Advanced Ceramic X Radiation Patterns-Type B XY cut @915MHz Vertical Horizontal XZ cut @915MHz Vertical Horizontal XY-V/XY-H XZ-V/XZ-H YZ-V/YZ-H 180 o 270 o 0 o 90 o X Z Y XY-cut scanning direction 180 o 270 o 0 o 90 o X Z Y XZ-cut scanning direction 180 o 270 o 0 o 90 o X Y Z YZ-cut scanning direction XZ cut @915MHz Vertical Horizontal AT7020-AR90HAAT/LF REV:5 PAGE:8/11 ACX Advanced Ceramic X Taping Specifications Tape & Reel Dimensions (Unit: mm) vs. Quantity (pcs) Type A A’ B C D E F T Quantity/per reelTape material AT7020 4.0± 0.1 4.0± 0.1 2.4± 0.1 7.3± 0.1 2.0± 0.05 5.5± 0.1 12.0± 0.1 1.45± 0.1 1,000pcs Plastic (Embossed) Reel Dimensions (Unit: mm) Leader and Trailer Tape Type W2 W3 W4 W5 AT5020 178±1 60±0.5 1.485±0.5 13±0.5 F A’ D E 1.75 ± 0.1 AB EMBOSS TA P E T C ∣ Trailer End Trailer (160 mm min.) Leader End Empty Compartments with Cover Tape (500 mm min.) W2 13.5±0.5 2.5±0.5 Label Label: Customer’s Name, ACX P/N, Q’ty, Date, ACX Corp. W4 W5 W3 AT7020-AR90HAAT/LF REV:5 PAGE:9/11 ACX Advanced Ceramic X Peel-off Force Peel-off force should be in the range of 0.2 – 1.20 N at a peel-off speed of 300±10 mm/min . Storage Conditions (1) Temperature: 5 ~35°C, relative humidity (RH): 45~75%. (2) Non-corrosive environment Notes The contents of this data sheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. Peeling Direction Top Cover Tape Carrier Tape <10 0 AT7020-AR90HAAT/LF REV:5 PAGE:10/11 ACX Advanced Ceramic X Mechanical & Environmental Characteristics Item Requirements Procedure Solderability 1. No apparent damage 2. More than 95% of the terminal electrode shall be covered with new solder 1. Preheat: 120 5 o C 2. Solder: 245 5 o C for 5 1 sec Soldering strength (Termination Adhesion) 1. 1kg minimum 1. Solder specimen onto test jig. 2. Apply push force at 0.5mm/s until electrode pads are peeled off or ceramic are broken. Pushing force is applied to longitude direction Deflection (Substrate Bending) 1. No apparent damage 1. Solder specimen onto test jig (FR4, 0.8mm) using the recommend soldering profile. 2. Apply a bending force of 1mm deflection Heat/Humidity Resistance 1. No apparent damage 2. Fulfill the electrical specification after test 1. Temperature: 85 2 o C 2. Humidity: 90% ~ 95% RH 3. Duration: 1000±48hrs 4. Recovery: 1-2hrs Thermal shock (Temperature Cycle) 1. No apparent damage 2. Fulfill the electrical specification after test 1. One cycle/step 1：125 ± 5C for 30 min step 2：- 40 ± 5C for 30 min 2. No of cycles：100 3. Recovery:1-2 hrs Low Temperature Resistance 1. No apparent damage 2. Fulfill the electrical specification after test 1. Temperature: -40 o  5 o C 2. Duration: 500 ±24hrs 3. Recovery: 1-2hrs 90mm Pressure Rod R230 AT7020-AR90HAAT/LF REV:5 PAGE:11/11 ACX Advanced Ceramic X Soldering Conditions Typical Soldering Profile for Lead-free Process Reflow Soldering : Notes The contents of this data sheet are subject to change without notice. Please con…

Text truncated - open the document above for the full version.

Page 1 of 30 FCC Test Report Report No.: AGC16184240502FR01 FCC ID : 2AJQ6MMF-15088 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : FEED HUB UNIVERSAL BRAND NAME : MOULTRIE MOBILE MODEL NAME : MMF-15088 APPLICANT : EBSCO Industries Inc., DBA PRADCO Outdoor Brands DATE OF ISSUE : Jun. 06, 2024 STANDARD(S) : FCC Part 15 Subpart C §15.249 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC16184240502FR01 Page 2 of 30 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 06, 2024 Valid Initial Release Report No.: AGC16184240502FR01 Page 3 of 30 TABLE OF CONTENTS 1. GENERAL INFORMATION .............................................................................................................................. 5 2. PRODUCT INFORMATION .............................................................................................................................. 6 2.1 PRODUCT TECHNICAL DESCRIPTION ................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ................................................................................................... 6 2.3 RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................. 7 2.4 TEST METHODOLOGY .......................................................................................................................... 7 2.5 SPECIAL ACCESSORIES ....................................................................................................................... 7 2.6 EQUIPMENT MODIFICATIONS .............................................................................................................. 7 2.7 ANTENNA REQUIREMENT .................................................................................................................... 7 3. TEST ENVIRONMENT ..................................................................................................................................... 8 3.1 ADDRESS OF THE TEST LABORATORY .............................................................................................. 8 3.2 TEST FACILITY ....................................................................................................................................... 8 3.3 ENVIRONMENTAL CONDITIONS........................................................................................................... 9 3.4 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 3.5 LIST OF EQUIPMENTS USED ............................................................................................................. 10 4. SYSTEM TEST CONFIGURATION ................................................................................................................ 11 4.1 EUT CONFIGURATION ......................................................................................................................... 11 4.2 EUT EXERCISE ..................................................................................................................................... 11 4.3 CONFIGURATION OF TESTED SYSTEM ............................................................................................ 11 4.4 EQUIPMENT USED IN TESTED SYSTEM........................................................................................... 11 4.5 SUMMARY OF TEST RESULTS ........................................................................................................... 12 5. DESCRIPTION OF TEST MODES ................................................................................................................. 13 6. RADIATED EMISSION ................................................................................................................................... 14 6.1. TEST LIMIT ........................................................................................................................................... 14 6.2. MEASUREMENT PROCEDURE .......................................................................................................... 15 6.3. TEST SETUP ........................................................................................................................................ 17 6.4. TEST RESULT ...................................................................................................................................... 18 7. BAND EDGE EMISSION ................................................................................................................................ 22 7.1. TEST LIMIT ........................................................................................................................................... 22 7.2. MEASUREMENT PROCEDURE .......................................................................................................... 22 7.3 TEST SETUP ......................................................................................................................................... 22 7.4 TEST RESULT ....................................................................................................................................... 23 8. 20DB BANDWIDTH & 99% BANDWIDTH .................................................................................................... 25 8.1. MEASUREMENT PROCEDURE .......................................................................................................... 25 Report No.: AGC16184240502FR01 Page 4 of 30 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 25 8.3. MEASUREMENT RESULTS................................................................................................................. 26 9. LINE CONDUCTED EMISSION TEST ........................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC16184240502AP01 Page 1 of 1 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz ****************************************End of Report*************************************